HC284PUB (HSG1457) LCD Monitor
User’s Manual OSD[V6.1] Before operating the monitor, please read this manual thoroughly. This manual should be retained for future reference. This device complies with requirement of EMC directive 2014/30/EU with regard to Electromagnetic Compatibility, and 2014/35/EU and 93/68/EEC with regard to Low Voltage directive. Socket-outlet shall be near the equipment and shall be accessible. Trademark Notice: HANNspree products incorporate High-Definition Multimedia Interface (HDMI™) technology.
User’s Manual RECYCLING INFORMATION We, at HANNspree care very much about our environment protection strategy and firmly believe that it helps us have healthier earth via appropriate treatment and recycling of industrial technology devices at the end-of-life. These devices contain recyclable materials, which can be re-decomposed and re-integrated into brand-new marvels. On the contrary, other material can be classified to hazardous and poisoned substances.
User’s Manual TABLE OF CONTENTS SAFETY NOTICE .................................................................................................. 5 PRECAUTIONS................................................................................................. 5 SPECIAL NOTES ON LCD MONITORS ...................................................... 6 BEFORE YOU OPERATE THE MONITOR ...................................................... 7 FEATURES......................................................................
User’s Manual SAFETY NOTICE 1. The changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 2. Shielded interface cables and AC power cord, if any, must be used in order to comply with the emission limits. 3. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modification to this equipment. It is the responsibilities of the user to correct such interference. 4.
User’s Manual SPECIAL NOTES ON LCD MONITORS The following symptoms are normal with LCD monitor and do not indicate a problem. Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn off the Power Switch and then turn it on again to make sure the flicker disappears. You may find slightly uneven brightness on the screen depending on the desktop pattern you use. The LCD screen has effective pixels of 99.99% or more. It may include blemishes of 0.
User’s Manual BEFORE YOU OPERATE THE MONITOR FEATURES 71,12cm / 28” Wide Screen TFT Color LCD Monitor Crisp, Clear Display Ergonomic Design Space Saving, Compact Case Design CHECKING THE CONTENTS OF THE PACKAGE The product package should include the following items: LCD Monitor Cables and User manual Adapter Power Cord DP Cable Quick Start Guide Warranty Card Energy Label 7
User’s Manual INSTALLATION INSTRUCTIONS INSTALL REMOVE Figure.1. Installing and Removing the Base POWER POWER SOURCE: 1. Make sure that the power cord is the correct type required in your area. 2. This LCD monitor has an Internal universal power supply that allows operation in either 100/120V AC or 220/240V AC voltage area (No user adjustment is required.) 3.
User’s Manual SETTING THE MONITOR ON THE WALL DISSEMBLING THE STAND BASE: 1. Disconnect all the cables and cords from the Monitor to prevent breakage. 2. Carefully place the Monitor face down on a soft and flat surface (blanket, foam, cloth, etc) to prevent any damage to the Monitor. (For reference only) WALL MOUNTING THE MONITOR: 1. Purchase a VESA compatible wall bracket: VESA 100×100mm, 4 holes, M4, 10mm, 8kg. 2. Locate your ideal Monitor position on the wall. 3.
User’s Manual MAKING CONNECTIONS CONNECTING TO A PC You can setup your monitor with the below suggested connections. Ensure your monitor is off during this process. 1. Connect one end of the DP cable to the back of the monitor and connect the other end to the computer’s DP port. 2. Connect one end of the HDMI cable (optional) to the back of the monitor and connect the other end to the computer’s HDMI port. 3. Connect the audio cable between the monitor's audio input and the PC's audio output (green port).
User’s Manual ADJUSTING THE VIEWING ANGLE For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitor’s angle to your own preference. Hold the stand so you do not topple the monitor when you change the monitor’s angle. You are able to adjust the monitor’s angle from -5 to 15. Figure.3. Monitor Angle NOTES: Do not touch the LCD screen when you change the angle. It may cause damage or break the LCD screen.
User’s Manual OPERATING INSTRUCTIONS GENERAL INSTRUCTIONS Press the power button to turn the monitor on or off. The other control buttons are located on the front panel of the monitor (See Figure 4). By changing these settings, the picture can be adjusted to your personal preferences. The power cord should be connected. Connect your display cable from the monitor to your devices display input port. Press the power button to turn on the monitor. The power indicator will light up.
User’s Manual FRONT PANEL CONTROL Power Button: Press this button to switch ON/OFF of monitor’s power. Power Indicator: Blue Red — Power On mode. — Power Saving mode. MENU / ENTER: Turn the OSD menu on/off or enter to the previous menu. Adjust ▲▼: 1. Adjust Brightness and volume when the OSD is off. 2. Navigate through adjustment icons when OSD is ON or adjust a function when function is activated. 【 E 】Button: 《Digital Input Models》 1. Press【 E 】to enter Source selections.
User’s Manual HOW TO ADJUST A SETTINGS INPUT SOURCE AUTO SOURCE From the Signal Selection menu, select the「Auto Source」option to activate the automatic signal search function. DP Select the「DP」option to change the DP source. HDMI Select the「HDMI」option to change the HDMI source. BRIGHTNESS/ CONTRAST BRIGHTNESS Adjust the brightness value of the display according to your preference. Select「BRIGHTNESS」option to adjust the brightness value.
User’s Manual SUPER RESOLUTION Select the super resolution according to your preference: Off/ High/ Middle/ Low. BLACK LEVEL Select the「BLACK LEVEL」option to adjust the black level of the display. DISPLAY ASPECT RATIO Setup the aspect ratio of screen through the aspect ratio function. Available settings are Wide Screen(16:9)/ 4:3/ 1:1/ Auto. AUDIO MUTE Select the「MUTE」option to switch the function On or Off. [The availability of this function depends upon the selected model.
User’s Manual OSD V-POSITION Select 「OSD V-POSITION」option to adjust the vertical position of the OSD. Enter the option and adjust the level. OSD TRANSPARENCY Select 「OSD TRANSPARENCY」option to adjust the transparency of the OSD. Enter the option and adjust the level. OSD TIME OUT Select 「OSD TIME-OUT」option to set the OSD time out from 5 to 100 seconds. Enter the option and adjust the level. OSD ROTATION Select「OSD Rotation」option to rotate the window of the OSD.
User’s Manual PLUG AND PLAY Plug & Play DDC2B Feature This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional information about its display capabilities. The DDC2B is a bidirectional data channel based on the I²C protocol. The host can request EDID information over the DDC2B channel.
User’s Manual TECHNICAL SUPPORT (FAQ) Q & A FOR GENERAL PROBLEMS PROBLEM & QUESTION POSSIBLE SOLUTION Power LED is not on *Check if the Power Switch is in the ON position. *Power Cord should be connected. No Plug & Play *Check if the PC system is Plug & Play compatible. *Check if the Video Card is Plug & Play compatible. *Check if any plug pins on the DP or HDMI connector are bent. The display is too dark or too bright. *Adjust the Contrast and Brightness Controls.
User’s Manual INPUT as a PC option, and make sure PC audio output cable is connected to monitor’s LINE IN port(or AUDIO IN port). [For HDMI Input only] Addendum related to Windows 7 / Windows 8 / Windows 10 When you encounter display problem under Windows 7/ Windows 8/ Windows 10, you need to do the following: 1. Make sure your PC computer (Hardware requirement) can support Windows 7/ Windows 8/ Windows 10. 2. Make sure your video card can run Windows 7/ Windows 8/ Windows 10. 3.
User’s Manual ERROR MESSAGE & POSSIBLE SOLUTIONS CABLE NOT CONNECTED: 1. Check that the signal-cable is properly connected, if the connector is loose, tighten the connector’s screws. 2. Check the signal-cable’s connection pins for damage. INPUT NOT SUPPORT : Your computer has been set to unsuitable display mode, set the computer to display mode given in the following table.
User’s Manual (Video mode) MODE RESOLUTION 1 640×480p @60Hz 3 720×480p @60Hz 4 720×576i @50Hz 5 720×576p @50Hz 6 1280×720p @50Hz 6 1280×720p @60Hz 8 1920×1080i @60Hz 9 1920×1080p @50Hz 10 1920×1080p @60Hz 11 2560×1080p @50Hz 12 2560×1080p @60Hz 13 3840×2160p @25Hz 14 3840×2160p @50Hz 15 3840×2160p @60Hz ** We ensure that the monitor can be lighted under interlace signal mode, but we can not guarantee the image quality.
User’s Manual APPENDIX SPECIFICATIONS LCD Panel Video Driving system TFT Color LCD Size 71,12cm / 28” Diagonal Pixel pitch 0,16mm(H) × 0,16mm(V) H-Frequency 30KHz – 135KHz V-Frequency 56Hz – 75Hz Display Colors 1.073G Colors Max. Resolution 3840 × 2160 @60Hz Plug & Play VESA DDC2BTM Power consumption ON Mode 27W (Typical) Power Saving Mode ≤ 0.5W OFF Mode ≤ 0.3W Audio output Rated Power 2.
