TILT And please read the instructions carefully before using.
Before nse Safety precautions Overall sketch Function introduction Installation guide Toilet installation... 8 Oration Operation introduction — fn Preparation 1 Product use 12 Troubleshooting... 13 Cleaning and Maintenance. ~~ 14 Pounding Product specification...
Please read the “safety precautions” carefully before use, all the precautions listed here are connected to safety. It's important and must be followed. Represents Improper operations by Ignoring tha Instructions may result In death or Injury Represents Improper operations by Ignoring the Instructions may result In body Injury and property loss The following signs are used for important safety precautions.
Please don't use seawater and other water except tap water or drinkable well water{underground water) «+ Or It may cause skin Inflammation or fault Please do not touch the electrical plug while thunder «+ Or it may cause electric shock Please do not let the water Inlet soft pipe connect to the electrical plug and outlet « Orin may cause fire, electric shock, heat, short circuit because of moisture condensation Please do not destroy power cable or plug Does not strike, yank, twist, excessively bend, damage,
Please confirm if the electrical outlet is connected to the ground + Or It may cause electric shock because of fault or short circuit. The outlet for power wire should obey the following rules. + Grit may cause fire or electric shock. 2.Please use high sensibility and fast respond leakage switch (rated induced currents below 15mA} or Insulating transformer to protect outlet loop. b.Please reserved the installation place for outlet and keep it away form bathtub.
Please do not use the product when it's loose. « Other toilet and seat may separate and fall off to cause body injury Please do not touch broken area. Orin may cause injury, please replace it as soon as possible. Please do not impact forcefully, put heavy subject or stand on the product « Or lt may causal product damage, fall down or body Injury + Orin may cause body injury or indoor water seepage Please do not pull the product by holding the sat or cover.
Please close the angle valve when water leaking When room temp is under 0'C, to avoid piping or soft hose damaging because of frozen, natl freezing measures should be adopted. + It may destroy main body or piping, leading to water leakage If water Inst soft hose Is frozen. + To avoid damage, please pay attention to room temp adjustment. When not use for a long time, please must drain the inlet soft hose, and cut tha power. + When using next ime, please open the angle valve and let water connected first.
EET EE 0 EET The contents described in this manual include but are not limited to product material, process, functional characteristics, etc., which may be different from the actual product dus to process Improvement or product upgrade. Pleads refer to the actual product.
Seat sensor Functions activated by ig on the seat Auto flush Auto bowl ult cleaning after users walk away Ceramic bowl per-wet Water coma out of the nozzle to make the ceramic bowl wet Seat temperate adjustment Adjust the seat temperature
Le Le 1.Turn on the old supply stop and flush for 1 minute, to flush out any sundries that may damage the toilet structure. 2.Tum off the supply stop and removal i 2. Wrap 13-15 turns of sealing tape on the NPT male) thread of the water supply pipe(not provided) to ensure good sealing performance. Screw the adapter onto the ‘water supply pips, ensuring that the direction of the adapter arrow Is as shown In the grue. 4.
For new installations, toilet flanges need 10 be Installed. Install flange bolts. Lift the toilet seat-lid assembly from the toilet.Lift from the interior,back right. Nate: Do not excessively pull the cover when lifting the toilet seat-lid assembly. Sewage Outer Install a sealing ring under the toils. Install the toilet to the flans and ensure that the bolts ars aligned with ths holes In the toilet. (from the top) Plastic Gaskets Use a ranch to lock nuts and other accessories to the fixing bolts.
A 1. Carsfully remove the cover of the battery case. 2.Connect and Install the battery and slide the cover back to the battery box. 3.Press the control dial on the side to confirm that flushing can be normal. Over Baptistery Note: Use alkaline battery. «This battery Is used to maintain the flushing function in the event of power Control Dial allure. Don't throw used batteries into the garbage can, pleads throw them Into your local battery collation center.
~ 1.0pen the angle valve -s Switch to this poi ( 2.Confirm power plug Is wall plugged Into the electric outlet.
Seat Sensor react automatically when sitting on the seat. Water comes out to per-waet the Inner ceramic bowl. In the sh wn z The indicator light of the knob does not light up, the front rotation/back rotation/pressing, ofc. well be turned on, the product automatically enters the standby state. When the pr n r power off : Press the knob to start flushing. When flushing in standby. In the boot stat: Long press the knob for 35 to shut down, the Indicator light goes out .
it on seat condition, all the functions are available. Buzz twice: Off the seat condition, parts of the functions are available. Buzz three times or moral: There are faults of the product. Reminder Buzzer only works when operate on remote controller or side button or initialization. Operating Instruction: When the foot has crossed the sensor switch at the bottom, the flushing function Is activated. Reminder: This function doesn't work when seated.
el TET 4 Please mask sure the electrical plug is taken out 4 Please use wettest soft cloth to wipe the toilet shelf and seat. The dirt should be cleaned as soon as possible, if it's difficult to clean, you can use neutral detergent. Gel LT When the water pressure is too low or insufficient, please clean the filter. expansionist vain sandstone watt sunny Notice: Do not remove the filter without closing the angle valve. -—Otherwise water will spray out.
3 mE Get the filter out and clean It thoroughly. -—Flush off dirt or clean the flier by toothbrush Note: Do not use any cleaning agents. Clean it with water only. Do not crush the filter when cleaning in sacs of distortion. 4 Err Reinstall filter based on the removal sequence. Notice: Open the shutoff valve after installation and confirm there's no water leakage.
1. Pull out power plug. 2. Lit toilet seat Id. 3. Take out battery cover. 4. Put battery in right position. 5. Press flush button, be sure It can flush normally. 6. Put cover back and fix toilet seat lid. ils Spare battery Se 1.The spare battery must use $V alkaline battery, Do not use carbon or other battery. 2.If the battery Is low or not Installed, It will cause the flushing to stop normally, and flushing even If power off function will be abnormal. 3.
Lg UE Dear user Pleas check whatever the products are complete after you open the box of toilet. Product packaging box containing the Items ars: Smollett S 1 Manual ha 1 Spanner 1 Angle valve {15/16” adapter, 1/2" adapter) 1 8V alkaline battery (6LR61) = 1 Waring © 1 Flooring {with 1 bag installation bolt) 1.
