Data Sheet

8 Appendix: Statement
Federal Communications Commission (FCC) Declaration ofConformity
FCC Caution: Any changes or modifications not expresslyapproved by the party
responsible for compliance could void the user'sauthority to operate this equipment.
This device complies with Part 15 of the FCC Rules.Operation is subject to the following
two
conditions: (1) This device may notcause harmful interference, and (2) this device
must accept any interferencereceived, including interference that may cause undesired
operation.
Note:
This equipment has been tested and found to complywith the limits for
digital device, pursuant to part 15 of the FCC Rules.These limits are designed to provide
reasonable protection against harmfulinterference in a residential installation. This
equipment generates, uses andcan radiate radio frequency energy and, i
and used inaccordance with the instructions, may cause harmful interference to
radiocommunications. However, there is no guarantee that interference will notoccur in a
particular installation. If this equipment does cause harmfulinterferenc
television reception, which can be determined byturning the equipment off and on, the
user is encouraged to try to correct theinterference by one or more of the following
measures:
—
Reorient or relocate the receiving antenna.
—Increase the se
paration between the equipment and receiver.
—
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
—
Consult the dealer or an experienced radio/TV technician for help.
Radiation Exposure Statement
This
equipment complies with FCC radiation exposure limits set forth for an
uncontrolledrolled environment. This equipment should be installed and operated with
minimumdistance 20cm between the radiator and your body.
Important Note
This radio module must not i
radios in host system
except in accordance with FCC multi
procedures.A
dditional testing and equipment authorization may berequired to operating
simultaneously with other radio
The availability of some specific channels and/or operational frequency bandsare country
dependent and are firmware programmed at the factory to matchthe intended
destination.The firmware setting is not accessible by the end user.
WBR1
20
Federal Communications Commission (FCC) Declaration ofConformity
FCC Caution: Any changes or modifications not expresslyapproved by the party
responsible for compliance could void the user'sauthority to operate this equipment.
This device complies with Part 15 of the FCC Rules.Operation is subject to the following
conditions: (1) This device may notcause harmful interference, and (2) this device
must accept any interferencereceived, including interference that may cause undesired
This equipment has been tested and found to complywith the limits for
digital device, pursuant to part 15 of the FCC Rules.These limits are designed to provide
reasonable protection against harmfulinterference in a residential installation. This
equipment generates, uses andcan radiate radio frequency energy and, i
and used inaccordance with the instructions, may cause harmful interference to
radiocommunications. However, there is no guarantee that interference will notoccur in a
particular installation. If this equipment does cause harmfulinterferenc
television reception, which can be determined byturning the equipment off and on, the
user is encouraged to try to correct theinterference by one or more of the following
Reorient or relocate the receiving antenna.
paration between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which
Consult the dealer or an experienced radio/TV technician for help.
Radiation Exposure Statement
equipment complies with FCC radiation exposure limits set forth for an
uncontrolledrolled environment. This equipment should be installed and operated with
minimumdistance 20cm between the radiator and your body.
This radio module must not i
nstalled to co-
locate and operating simultaneously withother
except in accordance with FCC multi
-
transmitter product
dditional testing and equipment authorization may berequired to operating
simultaneously with other radio
.
The availability of some specific channels and/or operational frequency bandsare country
dependent and are firmware programmed at the factory to matchthe intended
destination.The firmware setting is not accessible by the end user.
WBR1
-IPEX Datasheet
Federal Communications Commission (FCC) Declaration ofConformity
FCC Caution: Any changes or modifications not expresslyapproved by the party
responsible for compliance could void the user'sauthority to operate this equipment.
This device complies with Part 15 of the FCC Rules.Operation is subject to the following
conditions: (1) This device may notcause harmful interference, and (2) this device
must accept any interferencereceived, including interference that may cause undesired
This equipment has been tested and found to complywith the limits for
a Class B
digital device, pursuant to part 15 of the FCC Rules.These limits are designed to provide
reasonable protection against harmfulinterference in a residential installation. This
equipment generates, uses andcan radiate radio frequency energy and, i
f not installed
and used inaccordance with the instructions, may cause harmful interference to
radiocommunications. However, there is no guarantee that interference will notoccur in a
particular installation. If this equipment does cause harmfulinterferenc
e to radio or
television reception, which can be determined byturning the equipment off and on, the
user is encouraged to try to correct theinterference by one or more of the following
Connect the equipment into an outlet on a circuit different from that to which
equipment complies with FCC radiation exposure limits set forth for an
uncontrolledrolled environment. This equipment should be installed and operated with
locate and operating simultaneously withother
transmitter product
dditional testing and equipment authorization may berequired to operating
The availability of some specific channels and/or operational frequency bandsare country
dependent and are firmware programmed at the factory to matchthe intended