User's Manual

10
20
30
40
50
60
70
80
90
100
DS-PRP100
Security Radar
Diagram References
ENGLISH
Indicator
Installaon
For detailed sengs, scan the QR code to get the User Manual of Security Radar.
1. Download and install the iVMS-4200 client soware.
2. Enter Device Management page, and click Online Device.
Note: You should acvate the device for the first usage. Select the device in the Online Device List, click
Acvate, create a password to acvate the device.
Scan the QR code to get the User Manual of Security Radar.
3. Select the radar in the Online Device List. Click Add
, set the port as 80, and check Import to Group. If the
IP segment of the radar is not the same as the PC’s, click Add in the Device for Management list and enter
the radar IP address in the pop-up window to add the radar. You need to set the port as 80 and check Import
to Group.
4. Upload Map: In iVMS-4200 client soware, enter E-map, select a radar and click Add map to select a map.
5. Click Edit Scale, draw a path on the map and set the plong scale.
6. Expand the device group in the list on the le, and drag the radar onto the map.
7. Move along the edge of the required monitoring filed. Make sure the target sign (red arrow) is moving within
the radar area (gray sector) shown on the added map. If the target sign is not within the sector, you need to
adjust the mounng posion or angle of the radar.
Power on the radar and make sure there is no large object in the monitoring area. Make the detector access
into the Internet. The radar and the PC that runs the soware should be in the same IP segment.
Test the radar aer installaon to make sure it is properly mounted.
1. In iVMS-4200 client soware, select the radar on Device Management page and click to enter the
configuraon page. You can also enter the device IP address in the web browser to enter the configuraon
page.
2. Click Smart Rule Sengs - Camera Linkage Sengs.
3. Click + to add cameras to the radar.
4. Select a camera in the Camera IP Address list, and select the radar zone or the alarm line (or whole field) in
the Zone Linkage list or the Alarm Line list.
5. Add the camera to iVMS-4200 client soware: In the client soware, enter Device Management page, click
Add
in the Device for Management list, and enter the IP address, user name and password of the camera in
the pop-up window.
1. Select a reference object about 50 m away from the speed dome. On the reference object, select a point
whose altude is the same as the speed dome’s.
2. Enter the IP address of the speed dome in the web browser to enter the web client. Adjust the PTZ buons
on the Live View page to make the reference object displayed in the image, and click to zoom in the
reference object.
3. Click , and click the reference point to middle the point in the frame.
4. Enter Configuraon - PTZ - Inial Posion, and click Set to set the inial posion.
Link the camera to the Zone
Before calibraon, set the inial posion of the speed dome to ensure the tracking accuracy.
1. In iVMS-4200 client soware, enter Device Management page, click Group. Click Encoding Channels in the
group of the radar. Click Import and check cameras to link with the radar.
2. In iVMS-4200 client soware, enter E-map page, click Edit - RadarEdit - MasterSlaveEdit.
3. Click the live view window, select the linked camera needs to be calibrated, and double click the live view
window to maximum it.
4. Select Single Calibraon
as the calibraon mode.
5. Ask the calibraon staff to move in the radar detecon field. Click the track of the calibrate staff, and the
color of the selected track will change from red to white.
6. Click Add Cal to add a calibraon point.
7. Ask the calibraon staff to stand at the calibraon point within 20 to 40 m directly in front of the radar.
Note: The track disappears if the calibraon staff is standing in the place for more than 7 s. If the calibraon
staff does not move to the calibraon point when the track disappears, you need to ask the calibraon staff to
move again, and click the track of the calibraon staff to connue the calibraon.
8. Click the added calibraon point in the Info list to update the radar posion of the calibraon staff.
9. Adjust the PTZ buons on the right of the live view window to update the PTZ posion: Click +/- to scale
the calibraon staff to a fit size (The altude of the calibraon staff is about 2/3 of the altude of the window),
and adjust the PTZ to make the object align with the sign + at the center of the frame.
10. Select the live view window of the speed dome, and Check Enable Tracking.
11. Click Sure.
Calibrate the Speed Dome
Calibraon
Inial Posion sengs
Test
1
4
Wiring
3
Formang
2
5
Set Up
6
Specificaon
1. Aach the mounng bracket on the detector with four supplied screws.
2. Loosen the screws on both side of the bracket.
3. Adjust the angle of the detector.
4. Tighten the screws on both sides of the bracket to complete the installaon.
1. Aach the mounng bracket on the detector with four supplied screws.
2. Loosen the screws on both sides of the bracket.
3. Adjust the angle of the detector.
4. Tighten the screws on both sides of the bracket to complete the installaon.
a. Power Supply Indicator
Solid Green: Detector Power on
b. Fault Alarm Indicator
Flashing Red: Fault Alarm Occurred
Solid Green: Alarm Restored
c. Zone Alarm Indicator
Solid Red: Zone Alarm Occurred
Solid Green: Alarm Restored
d. Formang Indicator
Red and Green LED Flashes 3 Times: Formang
Successfully
a. Alarm Output Wiring (4-Ch Weak Current Output)
b. Alarm Input Wiring (Reserved)
c. DC Power Supply Wiring
d. Ethernet (PoE Port) Wiring
e. Grounding
Loosen the screws on the rear cover to remove the
cover. Hold the Reset buon while powering the
radar on unl the red and green LED flashes 3
mes.
Ceiling Mounng
Pole Mounng
Before You Start:
The recommended installaon height is 2.5 m.
Make sure that the mounng surface is strong enough to withstand at least 50 N, as well as four mes the
weight of the device and the bracket.
1. In iVMS-4200 client soware, enter E-map.
2. Click Edit - RadarEdit - AddZone or AddAlarmLine, and click to draw a zone or an alarm line on the radar
detecon area.
3. Right-click to finish drawing.
4. Set the parameters of the zone or alarm line in the pop-up window.
Zone: edit the zone parameters in the pop-up window. Click OK to finish the sengs.
Alarm Line: set the rule of the line (le->right, le<-right, le<->right). Click OK to finish the sengs.
Add Zone or Trigger Line for the Detector
If the speed dome is installed together with the radar, select the calibraon mode as Single Calibraon. Otherwise,
set the calibraon as Mulple Calibraon.
For single calibraon, you can refer to the following steps, and see user manual for mulple calibraon.
Note: The alarm line is not allowed to be crossed.
Before the operaon, you need to click RadarArm - AllRadarDisarm on the E-map
page or click the selected
radar and click disarm to disarm the radar.
1
1
2
2
3
COPYRIGHT ©2019 Hangzhou Hikvision Digital Technology Co., Ltd.
ALL RIGHTS RESERVED.
Any and all informaon, including, among others, wordings, pictures, graphs are the properes of Hangzhou Hikvision Digital Technology Co., Ltd. or its subsidiaries
(hereinaer referred to be “Hikvision”). This user manual (hereinaer referred to be “the Manual”) cannot be reproduced, changed, translated, or distributed, parally
or wholly, by any means, without the prior wrien permission of Hikvision. Unless otherwise spulated, Hikvision does not make any warranes, guarantees or
representaons, express or implied, regarding to the Manual.
About this Manual
This Manual is applicable to the Security Radar.
The Manual includes instrucons for using and managing the product. Pictures, charts, images and all other informaon hereinaer are for descripon and
explanaon only. The informaon contained in the Manual is subject to change, without noce, due to firmware updates or other reasons. Please find the latest
version in the company website (hp://overseas.hikvision.com/en/).
Please use this user manual under the guidance of professionals.
Trademarks Acknowledgement and other Hikvision’s trademarks and logos are the properes of Hikvision in various jurisdicons. Other
trademarks and logos menoned below are the properes of their respecve owners.
Product Informaon
This product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore with the applicable harmonized
European standards listed under the RE Direcve 2014/53/EU, the EMC Direcve 2014/30/EU, the LVD Direcve 2014/35/EU, the RoHS
Direcve 2011/65/EU.
2012/19/EU (WEEE direcve): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For
proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collecon
points. For more informaon see: www.recyclethis.info
2006/66/EC (baery direcve): This product contains a baery that cannot be disposed of as unsorted municipal waste in the European Union.
See the product documentaon for specific baery informaon. The baery is marked with this symbol, which may include leering to
indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the baery to your supplier or to a designated collecon point.
For more informaon see:www.recyclethis.info
This product operates in a European non-harmonised frequency band.
1 3
4
6
206.5 mm
228.5 mm
60.8 mm
2
a
b
c
d
NC
NO
……
……
NO COM NC
NO COM NC
b
c
d
2
4
1 2
50 m
09-29-2018 16:50:20
+
+
3D
3D
09-29-2018 16:51:22
09-29-2018 16:51:22
+
H H=h h
Initial Position
09-29-2018 16:52:07
a
b
e
1 (-24.29,42) (12,25,34)
1 (-19.79,34) (31,43,17)
a
b
Before the operaon, you need to disable the parking funcon, and set the inial posion of the speed
dome. You also need to disarm the radar.
ISED RSS Warning:
This device complies with Innovation, Science and Economic Development Canada licence-exempt RSS standard(s). Operation is subject to the following two
conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'ISED applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
ISED RF exposure statement:
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator& your body.This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
Le rayonnement de la classe b repecte ISED fixaient un environnement non contrôlés.Installation et mise en œuvre de ce matériel devrait avec échangeur
distance minimale entre 20 cm ton corps.Lanceurs ou ne peuvent pas coexister cette antenne ou capteurs avec d’autres.
NO4
NC4
COM4
NO3
NC3
COM3
NO2
NC2
COM2
NO1
NC1
COM1
a
10
20
30
40
50
60
70
80
90
100
Radar
Radar
Edit Map Edit Scale RadarEdit
Edit Map Edit Scale RadarEdit
MasterSlaveEdit
Excepon detecon
Tampering alarm
Moving alarm
Power DC 12 V
Operaon temperature
–40 °C to 65 °C
Operaon humidity 10% to 90%
Dimension (W × H × D) DC 12 V
IP level
IP67
Weight 1.73 kg
Installaon
Bracket installaon
Installaon height: 1.2m to
4m
Recommended height: 2.5m
UD16651B
Model DS-PRP100
D
etecon range 100 m
H
orizontal angle 10°
Distance
m
easurement
accuracy
1.2 m
M
ax. target number 5
V
elocity range 9 to -9 m/s
A
larm line 4
Z
one 8
R
elay output
4-ch weak current output:
DC 5 VC, 0.5 A/125 AVC, 300 mW
N
etwork interface
1 RJ45 10 M/100 M
self-adapve, supports POE
C
ommunicaon prot
ocol
Standard ISAPI protocol, NAL2300
protocol, HTTP, DNS, NTP, TCP, UDP,
DHCP, ARP and SSH