User's Manual
Table Of Contents
- Legal Information
- Regulatory Information
- Safety Instruction
- Available Models
- Chapter 1 Overview
- Chapter 2 Installation
- Chapter 3 Wiring
- Chapter 4 Device Settings
- Chapter 5 Activation
- Chapter 6 Client Software Configuration
- 6.1 Configuration Flow of Client Software
- 6.2 Device Management
- 6.3 Group Management
- 6.4 Person Management
- 6.4.1 Add Organization
- 6.4.2 Configure Basic Information
- 6.4.3 Issue a Card by Local Mode
- 6.4.4 Upload a Face Photo from Local PC
- 6.4.5 Take a Photo via Client
- 6.4.6 Collect Face via Access Control Device
- 6.4.7 Collect Fingerprint via Client
- 6.4.8 Configure Access Control Information
- 6.4.9 Customize Person Information
- 6.4.10 Configure Resident Information
- 6.4.11 Configure Additional Information
- 6.4.12 Import and Export Person Identify Information
- 6.4.13 Import Person Information
- 6.4.14 Import Person Pictures
- 6.4.15 Export Person Information
- 6.4.16 Export Person Pictures
- 6.4.17 Get Person Information from Access Control Device
- 6.4.18 Move Persons to Another Organization
- 6.4.19 Issue Cards to Persons in Batch
- 6.4.20 Report Card Loss
- 6.4.21 Set Card Issuing Parameters
- 6.5 Configure Schedule and Template
- 6.6 Set Access Group to Assign Access Authorization to Persons
- 6.7 Configure Advanced Functions
- 6.7.1 Configure Device Parameters
- 6.7.2 Configure Remaining Open/Closed
- 6.7.3 Configure Multi-Factor Authentication
- 6.7.4 Configure Custom Wiegand Rule
- 6.7.5 Configure Card Reader Authentication Mode and Schedule
- 6.7.6 Configure First Person In
- 6.7.7 Configure Anti-Passback
- 6.7.8 Configure Device Parameters
- 6.8 Configure Linkage Actions for Access Control
- 6.9 Door Control
- 6.10 Event Center
- 6.11 Time and Attendance
- 6.12 Remote Configuration via Client Software
- 6.12.1 Check Device Information
- 6.12.2 Edit Device Name
- 6.12.3 Edit Time
- 6.12.4 Set System Maintenance
- 6.12.5 Manage Network User
- 6.12.6 Manage Keyfob User
- 6.12.7 Set Security
- 6.12.8 Configure Screen Parameters
- 6.12.9 Configure Screen Parameters
- 6.12.10 Configure Advanced Network
- 6.12.11 Configure Audio File
- 6.12.12 View Relay Status
- Appendix A. Tips for Scanning Fingerprint
- Appendix B. DIP Switch
- Appendix C. Event and Alarm Type
- Appendix D. Table of Audio Index Related Content
- Appendix E. Communication Matrix and Device Command
6.8.3 Congure Device Acons for Card Swiping
You enable access control device's linkage acons (such as disarming a zone and triggering audio
prompt) for the swiping of a specic card, In this way, you can monitor the card holder's behaviors
and wher
eabouts.
Steps
Note
It should be supported by the device.
1. Click Access Con
trol → Linkage Conguraon .
2. Select the access control device from the list on the le.
3. Click Add to add a new linkage.
4. Select Card Linkage as the event source.
5. Enter the card number or select the card from the drop-down list.
6. Select the card reader where the card swipes.
7. In the Linkage Target area, set the property target to enable this acon.
Buzzer on Controller
The audible warning of access control device will be triggered.
Buzzer on Reader
The audible warning of card reader will be triggered.
Capture
An event-related picture will be captured when the selected event happens.
Recording
An event-related picture will be captured when the selected event happens.
Note
The device should support recording.
Alarm Output
The alarm output will be trig
gered for nocaon.
Alarm Input
Arm or disarm the alarm input.
Note
The device should support alarm input funcon.
Access Point
The door s
tatus of open, close, remain open, or remain closed will be triggered.
Audio Play
DS-K3G501 Series Tripod Turnsle User Manual
72