User's Manual
Table Of Contents
- Legal Information
- Regulatory Information
- Safety Instruction
- Available Models
- Chapter 1 Overview
- Chapter 2 Installation
- Chapter 3 Wiring
- Chapter 4 Device Settings
- Chapter 5 Activation
- Chapter 6 Client Software Configuration
- 6.1 Configuration Flow of Client Software
- 6.2 Device Management
- 6.3 Group Management
- 6.4 Person Management
- 6.4.1 Add Organization
- 6.4.2 Configure Basic Information
- 6.4.3 Issue a Card by Local Mode
- 6.4.4 Upload a Face Photo from Local PC
- 6.4.5 Take a Photo via Client
- 6.4.6 Collect Face via Access Control Device
- 6.4.7 Collect Fingerprint via Client
- 6.4.8 Configure Access Control Information
- 6.4.9 Customize Person Information
- 6.4.10 Configure Resident Information
- 6.4.11 Configure Additional Information
- 6.4.12 Import and Export Person Identify Information
- 6.4.13 Import Person Information
- 6.4.14 Import Person Pictures
- 6.4.15 Export Person Information
- 6.4.16 Export Person Pictures
- 6.4.17 Get Person Information from Access Control Device
- 6.4.18 Move Persons to Another Organization
- 6.4.19 Issue Cards to Persons in Batch
- 6.4.20 Report Card Loss
- 6.4.21 Set Card Issuing Parameters
- 6.5 Configure Schedule and Template
- 6.6 Set Access Group to Assign Access Authorization to Persons
- 6.7 Configure Advanced Functions
- 6.7.1 Configure Device Parameters
- 6.7.2 Configure Remaining Open/Closed
- 6.7.3 Configure Multi-Factor Authentication
- 6.7.4 Configure Custom Wiegand Rule
- 6.7.5 Configure Card Reader Authentication Mode and Schedule
- 6.7.6 Configure First Person In
- 6.7.7 Configure Anti-Passback
- 6.7.8 Configure Device Parameters
- 6.8 Configure Linkage Actions for Access Control
- 6.9 Door Control
- 6.10 Event Center
- 6.11 Time and Attendance
- 6.12 Remote Configuration via Client Software
- 6.12.1 Check Device Information
- 6.12.2 Edit Device Name
- 6.12.3 Edit Time
- 6.12.4 Set System Maintenance
- 6.12.5 Manage Network User
- 6.12.6 Manage Keyfob User
- 6.12.7 Set Security
- 6.12.8 Configure Screen Parameters
- 6.12.9 Configure Screen Parameters
- 6.12.10 Configure Advanced Network
- 6.12.11 Configure Audio File
- 6.12.12 View Relay Status
- Appendix A. Tips for Scanning Fingerprint
- Appendix B. DIP Switch
- Appendix C. Event and Alarm Type
- Appendix D. Table of Audio Index Related Content
- Appendix E. Communication Matrix and Device Command
Figure 3-4 Main Control Board
Acc
ording to the picture above, the serial port 1 to 6 refers to the RS-485/RS-232 interface. You can
use the jumper cap to change the communicaon type.
The main c
ontrol board descripons are as follows:
Serial Port 1
RS-485 communicaon interface. You can connect RS-485 card reader and so on.
Serial Port 5 Jumper Cap
Use the jumper cap to switch the serial port communicaon mode. You can switch between the
R
S-485 communicaon mode and the RS-232 communicaon mode. By default, it is in RS-485
communicaon mode.
Serial Port 2
RS-232 communicaon interface. You can connect the ngerprint and so on.
Serial P
ort 3 Jumper Cap
Use the jumper cap to switch the serial port communicaon mode. You can switch between the
R
S-232 communicaon mode and the RS-485 communicaon mode. By default, it is in RS-232
communicaon mode. Use the serial port to connect with ngerprint module.
Serial Port 4/Serial Port 6 Jumper Cap
Use the jumper cap to switch the serial port communicaon mode. You can switch between the
RS-484 communicaon mode and the RS-232 communicaon mode. By default, it is in RS-485
communicaon mode. Use the serial port to connect with face recognion module.
Serial P
ort 7/Serial Port 8
DS-K3G501 Series Tripod Turnsle User Manual
13