User's Manual

B Parts Introducon C Installaon D Mobile Phone Connecon E Funcon Descripon
7
F Cauons
8
G Troublshoong
9
G Troubleshoong
10
11
12
Model
Aperture
Pixel
Resoluon
Angle
Screen
Storage
G-Sensor
Wi-Fi
Sound Recording
Power Supply
Power Consumpon
Operang Temperature and Humidity
Installaon Type
Dimensions (L × W × H)
Weight
AE-DC5313-C6
F1.6
320 × 640
1600p @ 30fps
130°
3”
TF card, 16 GB to 128 GB
Built-in, collision triggered recording and recording lock
Yes
Yes
5 VDC, 2 A
Approx. 3.5 W
-20 °C to 70 °C
(-4 F to 158 F). Humidity 95% or less.
General
90 × 88 × 70 mm (3.6ʺ × 3.5ʺ × 2.8ʺ)
Approx. 125 g (0.3 lb.)
Scan QR Code
<
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
Specificaons
1
3
Clean the windshield and
paste the electrostac film
onto it.
Avoid introducing air bubble.
DO NOT paste the film
repeatedly.
Peel off the release paper of
3M tape and install the
dashcam onto the center of
the electrostac film. Connect
the dashcam with one end of
the power cord along the red
line shown in figure.
Connect the other end of
power cord to the car
charger and connect car
charger to cigaree lighter.
Adjust the surveillance angle
and the installaon is
completed. The lt adjusng
angle is from -10° to 10°.
Scan the QR code to download and
install HikDashcam app.
Add the dashcam to the app.
a. Run the HikDashcam app.
b. Tap Wi-Fi Connecon.
c. In Wi-Fi list, select the Wi-Fi SSID
of the target dashcam and enter
Wi-Fi password to build
connecon.
• You can set the parameters of the
dashcam.
• For iOS, you need to go to Wi-Fi
sengs of your phone to connect
to the Wi-Fi of dashcam.
Edit the dashcam password to
acvate it to avoid abnormal
recording aer connecng to Wi-Fi.
1
Dashcam Wi-Fi default parameters:
• Wi-Fi SSID: HIKVISION-C6-XXXX
(XXXX refers to the last four
characters of verificaon code.)
• Wi-Fi password: 1234567890
(please edit password aer logging in
for the first me.)
Power On and Power Off
Power On: When you start up the engine, the dashcam powers on.
Power Off: When you turn off the engine, the dashcam powers off.
Recording
Two recording types are provided: Normal Reording and Emergency
Recording. Sound and mute recordings are selectable. Sound recording is set
as default. You can set audio sengs on the device or turn off sound
recoding in app.
Safety Instrucon
These instrucons are intended to ensure that users can use the product
correctly to avoid danger or property loss.
Cauons: Injury or equipment damage may occur if any of the cauons are
neglected.
• In the use of the dashcam, you must be in strict compliance with the local
laws and regulaons.
• You are recommended to install the dashcam on the locaon of rear
mirror to ensure the dashcam can record with the best surveillance view.
DO NOT install the dashcam on the locaon that will block the driver’s sight.
• Keep the user manual properly for future reference. See inial
connecon of dashcam in user manual.
• Purchase the TF card from legal channel. To ensure safe and
stable data transmission, it is recommended to use TF card of
Class 10 or above.
• Format the new TF card first before using the card.
• To protect TF card from damage, shut down the dashcam before
installing and uninstalling TF card.
• If the dashcam is directly connected with the vehicle power
system, you are recommended to power off the dashcam when
the engine is off. Disconnect cigaree lighter to avoid insufficient
voltage and abnormal startup. Reconnect cigaree lighter to
ensure dashcam work normally when you start the car again.
• Operang temperature is from -20 C to 70 C (-4 F to 158 F). To
protect the dashcam, DO NOT use it in high temperature, low
temperature, or high-humidity environment. Keep the dashcam
from rain and dust.
• The manual is subject to update. The funcons of dashcam may
vary according to different models.
*The driving assistance funcon of the device only sends alarm or warning to
the driver and cannot replace the driver’s judgement and operaon. With the
device, you also should drive carefully to avoid traffic accident or violaon.
Pedestrian or object recognion failure or recognion error may occur due to
external factors. DO NOT overly rely on the driving assistance funcon.
Trouble Soluon SoluonTrouble
The dashcam drops
easily.
Starng the dashcam
failed.
The dashcam powers
off easily.
Recording is
abnormal and
indicator is unlit.
Recording is blurred.
Recording is mute.
Dashcam reboots
itself.
Clean the windshield before installaon.
Check whether the vehicle is started and power
supply is normal.
Check whether the car charger is ghtly connected.
Restore to defaults: hold the RESET buon unl the
startup music is heard.
Make sure the power cord is in good condion.
Make sure the power cord is ghtly connected to the
according interfaces.
Make sure that the dashcam started up successfully.
Check whether the TF card is inserted.
Check the status of TF card, e.g. its format, its lifespan.
Change TF card if it is not well.
Make sure the protecve film is peeled off.
Check whether the windshield or the lens of dashcam
is blurred.
Set audio sengs on the device or turn on sound
recording in HikDashcam app.
Check whether the car charger is equipped with power
supply interface of 5 VDC, ≥ 2 A.
Mobile phone cannot
connect to dashcam.
Make sure HikDashcam app is installed.
Please restart the dashcam to the app.
The mobile phone
cannot display
recordings.
It may be relevant with the player or system of the
phone. Please connect TF card to your computer and
display the recordings.
TF card is not
detected when you
connect dashcam to
computer with the
supplied power cord.
Dashcam does not support data transmission and the
supplied power cord is only for charging.
If you need to transfer data, please connect TF card
to your computer.
Wi-Fi connecon
takes a long me.
It may be caused by the interferrence of the
surrounding Wi-Fi signals. Please use the dashcam in
an environment of less interferrence.
Shut down unnecessary programs in your phone to
release some resources for HikDashcam app and
reconnect Wi-Fi.
Dashcam Wi-Fi
password is forgoen.
The default password is 1234567890. If you have
revisied the password, regain the password by the
following steps.
1. Hold the RESET buon on dashcam unl the startup
music is heard and the dashcam is restored to
defaults.
2. Go to Wi-Fi Connecon interface in HikDashcam
app.
3. Select Wi-Fi SSID and log in with default password
1234567890.
1
2
3
Power Cord
Car Charger
Cigaree
Lighter
• The power mode of cigaree lighter may vary by different vehicle
types. Some may be powered constantly. In this case, please
make sure that the dashcam stops aer you turn off the vehicle
engine. Otherwise, insufficient voltage may occur to vehicle baery.
• Make sure you have connected the dashcam to power according to
Step 2 and Step 3 in Installaon secon.
·
Check whether the car charger is ghtly connected.
13
4
8
9
7
1
2
3
5
2
5
6
0
X
1
6
0
0
P
F
1
.
6
L
E
N
S
1. Reset Buon
(Restore the device to defaults.)
2. TF Card Slot
3. Lens
4. Microphone
5. Speaker
7. Power Interface
8. MicroUSB Interface
(It can be extended as GPS
or 4G interface.)
9. Screen
10. Buons
4
0°
10°
-10°
·
Check whether the 3M tape is ghtly scked to the
electrostac film before the installaon.
·
Turn on sound through the the audio control funcon
of the dashcam.
2
6
10
6. 3M Tape