Speed Dome Quick Start Guide
Radar PTZ Camera·Quick Start Guide Quick Start Guide © 2020 Hangzhou Hikvision Digital Technology Co., Ltd. All rights reserved. This Manual is the property of Hangzhou Hikvision Digital Technology Co., Ltd. or its affiliates (hereinafter referred to as “Hikvision”), and it cannot be reproduced, changed, translated, or distributed, partially or wholly, by any means, without the prior written permission of Hikvision.
Radar PTZ Camera·Quick Start Guide THE PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR LOSS. YOU ACKNOWLEDGE THAT THE NATURE OF INTERNET PROVIDES FOR INHERENT SECURITY RISKS, AND HIKVISION SHALL NOT TAKE ANY RESPONSIBILITIES FOR ABNORMAL OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER-ATTACK, HACKER ATTACK, VIRUS INSPECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER, HIKVISION WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED.
Radar PTZ Camera·Quick Start Guide Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC Conditions This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2.
Radar PTZ Camera·Quick Start Guide Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into Warnings and Cautions: Warnings: Neglecting any of the warnings may cause serious injury or death. Cautions: Neglecting any of the cautions may cause injury or equipment damage. Warnings Follow these safeguards to prevent serious injury or death.
Radar PTZ Camera·Quick Start Guide device is intended for installation in a restricted access location, access can only be gained by service persons or by users who have been instructed about the reasons for the restrictions applied to the location and about any precautions that shall be taken. The high beam of IR supplement light at the distance of 200 mm is classified as Risk Group 1 (RG1). The white alarm light in solid mode is classified as Risk Group 2 (RG2).
Radar PTZ Camera·Quick Start Guide Do not leave the battery in an extremely high temperature surrounding environment, which may result in an explosion or the leakage of flammable liquid or gas. Do not subject the battery to extremely low air pressure, which may result in an explosion or the leakage of flammable liquid or gas. Improper use or replacement of the battery may result in hazard of explosion. Replace with the same or equivalent type only.
Radar PTZ Camera·Quick Start Guide Table of Contents 1 Overview ...................................................................................................... 1 1.1 Radar PTZ Camera Overview ................................................................................ 1 1.2 Cable Interfaces ................................................................................................... 1 1.3 Alarm Output .........................................................................................
Radar PTZ Camera·Quick Start Guide 1 Overview Refer to the figure below for the cable interfaces of the device and the location of memory card slot. 1.1 Radar PTZ Camera Overview The figures below are for reference only, refer to the actual product as the standard. Radar Module Memory Card Figure 1-1 Overview of Radar PTZ Camera 1.2 Cable Interfaces The cable interfaces of the device are shown below. The cables are distinguished by different colors.
Radar PTZ Camera·Quick Start Guide Power Cord RS-485 Audio & Alarm Network Cable Figure 1-2 Cable Interfaces 1.3 Alarm Output Alarm output is shown below.
Radar PTZ Camera·Quick Start Guide 2 Installation Before you start: Check the package contents and make sure that the device in the package is in good condition and all the assembly parts are included. Notes: For better detection effect, it is recommended to install the device in spacious area without blocking. The tilt angle of the device should be less than 5°. The recommended mounting height is 4 to 5 m. The radar module should directly face to the target.
Radar PTZ Camera·Quick Start Guide For cement wall, you need to use the expansion screw to fix the bracket. The mounting hole of the expansion pipe on the wall should align with the mounting hole on the bracket. For wooden wall, you can just use the self-tapping screw to fix the bracket. Make sure that the wall is strong enough to withstand more than eight times the weight of the speed dome and the accessories. Water-proof treatment is required for cable connectors. Refer to Section 2.3 and 2.
Radar PTZ Camera·Quick Start Guide Radar Detection Range Figure 2-3 Install Head Cover 3. Hook the speed dome to the bracket with supplied safety rope.
Radar PTZ Camera·Quick Start Guide 4. Route and connect the cables through the head cover and bracket. Note: Water-proof treatment is required for cable connectors. Refer to Section 2.3 and 2.4 for details. Figure 2-5 Connect the Cables 5. Align the speed dome with the head cover. Use the wrench to tighten the lock screws.
Radar PTZ Camera·Quick Start Guide 2.2 Pendant Mounting Steps: 1. Drill four holes on the ceiling to match those on the pendant mount bracket. Figure 2-7 Pendant Mount 2. Route the cables through the bracket, then align the base plate to the holes and fix it to the ceiling with four screws. Figure 2-8 Route the Cables and Fix the Bracket on the Ceiling 3. Use the wrench to fix the head cover on the bracket. Note: Make sure the radar module can directly face to the moving target.
Radar PTZ Camera·Quick Start Guide Radar Detection Range Figure 2-9 Fix the Head Cover 4. Hook the speed dome to the bracket with supplied safety rope. Figure 2-10 Use Safety Rope to Hook the Camera with Bracket 5. Connect the cables, and align the speed dome with the head cover, using wrench to tighten the screws on the head cover.
Radar PTZ Camera·Quick Start Guide Note: Water-proof treatment is required for cable connectors. Refer to Section 2.3 and 2.4 for details. Lock Screws Figure 2-11 Finish the Installation 2.3 Installation of Network Cable Waterproof Jacket Purpose: If the camera is installed outdoor, you should use the waterproof accessory or tapes to waterproof the cables. Otherwise the cables might get wet or a short circuit occurs. ② ① ③ ④ ⑤ Align ③ ④ ⑥ ① Figure 2-12 Install Waterproof Jacket Steps: 1.
Radar PTZ Camera·Quick Start Guide 3. Place ⑤ onto the end of ⑥, and plug the RJ45 male connector into RJ45 female connector. 4. Screw ③ to ⑥ clockwise. 5. Push ② into ③. 6. Secure ① with the ③ in clockwise direction. 2.4 Installation of Water-proof Tape Purpose: If the camera is installed outdoor, you can use supplied water-proof tape to protect cable connectors and unused cables after the camera is secured on the installation surface. Steps: 1.
Radar PTZ Camera·Quick Start Guide Note: Make sure that all naked wires are all firmly wrapped in the water-proof tape. 4. Press the tape on both ends of the connector to make sure no water can get in as the figure below. Press e Pr ss ss Pre Press Figure 2-15 Press the Water-proof Tape 5. Wrap the water-proof tape around the remaining unused cables tightly as the figure below. Figure 2-16 Wrap the Unused Cables Note: Make sure that all naked wires are all firmly wrapped in the water-proof tape. 6.
Radar PTZ Camera·Quick Start Guide 2.5 Protective Measures for Outdoor Installation If the device is installed outdoors, necessary protective measures should be taken to ensure safety. Scan the following QR code to get protective measures for outdoor installation. 3 Activate and Access Network Camera Scan the QR code to get Activate and Visit Network Camera. Note that mobile data charges may apply if Wi-Fi is unavailable.
Radar PTZ Camera·Quick Start Guide 13 UD16629B-A
