ALGIZ 7 Vehicle Docking Quick Guide
ALGIZ 7 Vehicle Docking Quick Guide Copyright Notice Copyright © 2010 Handheld Group AB, ALL RIGHTS RESERVED. No part of this document may be reproduced, copied, translated, or transmitted in any form or by any means, electronic or mechanical, for any purpose, without the prior written permission of the original manufacturer. Trademark Acknowledgement Brand and product names are trademarks or registered trademarks of their respective owners.
ALGIZ 7 Vehicle Docking Quick Guide Customer Service We provide a service guide for any problems; see the following steps：First visit the website at http://www.handheldgroup.com to find the updated information about the product. Secondly, contact your distributor, sales representative, or our customer service center for technical support if you need additional assistance.
ALGIZ 7 Vehicle Docking Quick Guide Safety Precautions Safety Precautions Always completely disconnect the power cord from your chassis whenever you work with the hardware. Do not connect the electronic device with power socket while the device’s power is on. Sensitive electronic components can be damaged by sudden power surges. Only experienced electronics personnel should open the PC’s chassis mechanical housing. Caution! Always ground yourself to remove any static charge before touch the CPU card.
ALGIZ 7 Vehicle Docking Quick Guide (1) Please be aware that the power code of the adapter needs to be grounded. (2) Please notice the Power button needs to be pressed down for at least 4 seconds to go to power off or on. Battery Notice! WARNING Do not fix or replace the battery, this may cause explosion! Use only with the battery specified by the manufacturer and follow the instructions in the user’s guide.
ALGIZ 7 Vehicle Docking Quick Guide Content CHAPTER 1 INSTALLATION........................................................................................................................... 7 1.1 INTRODUCTION..................................................................................................................... 8 1.2 INSTALLATION.................................................................................................................9-10 CHAPTER 2 POWER AND I/O CONNECTOR SPECIFICATION..
ALGIZ 7 Vehicle Docking Quick Guide Chapter 1 Installation This Chapter introduces how to install the 7” Handheld Algiz 7 to the vehicle mount docking kit.
ALGIZ 7 Vehicle Docking Quick Guide 1.1 Introduction The Algiz 7 must be properly installed, according to the following instructions. You will need the appropriate fasteners, tools, and mounting kits listed in each section. When screwing, always check what is on the opposite side of the surface.
ALGIZ 7 Vehicle Docking Quick Guide 1.2 Installation Install the Algiz 7 handheld tablet pc to the vehicle mount docking station： 1 Put the female docking connector with the male docking pins on the vehicle mount docking station. 2 Connect them and push the top of the tablet pc into the vehicle mount docking station.
ALGIZ 7 Vehicle Docking Quick Guide 1.2 Installation To remove the Algiz 7 handheld tablet pc from the vehicle mount docking station: 1 Press the unlock handle. 2 Then push the top part of the tablet PC out from the vehicle mount docking station. 3 Remove it.
ALGIZ 7 Vehicle Docking Quick Guide Chapter 2 Power and I/O Connector Specification This Chapter describes the vehicle mount docking station connector types.
ALGIZ 7 Vehicle Docking Quick Guide 2.1 I/O Specification 2.1.1 Power Input There are two approaches to connecting to the power source, as described below. Using both of these in wide voltage range between 9~36V is acceptable. 1. 1 x DC 3 pins terminal block. Pin 1 Vin + Pin 2 Vin - Pin 3 N.C. 2. 1 x DC Input Jack (Optional) The vehicle mount docking station can be plugged into a cigarette power plug or the original AC/DC adapter.
ALGIZ 7 Vehicle Docking Quick Guide 2.1.2 Serial COM ports Two RS-232 connectors that can be connected to other RS-232 devices. 2.1.3 Ethernet interface The Ethernet port provides one standard RJ-45 port. Two LEDs are built into the RJ-45 LAN connector showing the LAN connection status. 2.1.4 USB ports The vehicle mount docking station supports two USB 2.0 ports. USB 2.0 support requires both an operating system and drivers that fully support USB 2.0 transfer rates. 2.1.
ALGIZ 7 Vehicle Docking Quick Guide 2.2 Power Specification The vehicle dock is equipped with two kinds of DC input choices. One is for a DC 9~36V input terminal block connector and another is for an AC/DC adaptor. Users can choose the appropriate connector to use, but do not connect the power source to both of these at the same time.
ALGIZ 7 Vehicle Docking Quick Guide Appendix – Docking System Diagram Appendix A: Function Block Diagram 15
ALGIZ 7 Vehicle Docking Quick Guide Appendix B: Exploded Diagram The exploded diagram is shown as below. There are front and rear covers, PCB, docking connector, fan, etc. 16 www.handheldgroup.
