UTS-1 Invisible Fast Wireless Charger User Instructions and Installation Guide
In the box 1. UTS - 1 charger 2. Apple & Samsung phone calibration template 3. 9cm + 8cm stickers 4. Screws 5. Cable management clips 6. Power adaptor 7. Country plug adaptor 8.
Check before installation ■ If you have a phone case please ensure it is flat and does not contain any metal, center magnets, card holders, pop sockets or kickstands. ■ Ensure the surface under your table is flat ■ Prepare a pencil and screwdriver if needed ■ Check installation area is within 1.5m(4’ 11’’) of your power point Installation Video Guide To watch the installation guide, please scan the QR code below or visit www.kewlabstech.
Stage 1 1. Use the desk sizing tool to measure your table’s compatibility. If you are not within the coloured area, you should not install the charger. please note the H(high) and L(low) setting indicator for later. 2. Place your mobile phone where you want to charge it. 3.
4. Choose between screw or tape installation. Tape or screw the charger into position making sure the charger still reaches the power point . (screws may be easier to remove) OR 5. Use the cable clips to attach the power cable to your table. Plug the power cable into either port Use only one of the two ports.
Stage 2 Phone calibration - how to make sure your phone is positioned correctly and charging. 1. Swich the toggle to “C” position 2. Select a sticker template guide according to your phone size or personal preference. See suggested sizing below Small phone 8cm template Apple/Samsung users Align your phone to fit your phone model 3.
4. Use the phone template handle to slowly move your device closer to the charging area and listen for the increasing speed of the audio beeps. - Please allow up to 1 second before Lorem ipsum moving your device to re-position. - As the audio beeps get faster, you are getting closer to the centred charging position. - When the sound changes to a solid signal you have reached your perfect charging area. 5.
6. Switch the toggle position of the charger to the correct thickness setting for your surface (either 20mm or 25mm) *Use setting tool on packaging as a reference. 7. Audio Confirmation Beep Configuration. Change your height toggle switch to calibration (C) mode and switch back to your original height (H/L) position and listen for the number of audio beeps. 1 beep = disabled audio confirmation buzzer 2 beeps = enabled audio confirmation buzzer Repeat again to disable or enable depending on preference.
User instructions 1. Place your phone face up aligning the center of your phone to the center of the sticker. 2. The UTS-1 will make an audio confirmation beep confirming that charging has started. If you do not hear this beep, please realign your phone more centrally or lift it off and reattempt.
Trouble Shooting and FAQs For all other queries and questions please email support@kewlabstech.com or find us on our Facebook messaging page.
● Can I switch the audio confirmation off? ○ Yes – if you would prefer or need to use the charger without the audio confirmation buzzer system, you are able to turn it off. However, without the audio confirmation, your phone is not necessarily charging just through the charging indication on your screen which is why the audio buzzer system was initially created. If you choose to use the device without the buzzer, please ensure your alignment and setup is correct and accurate. ■ ● To disable the buzzer.
■ SPECIFICATIONS • Fast Charging Speeds - Qi enabld 9W Fast Charge • Charging Distance - 18mm ~ 25mm (0.7’ ~ 1.0’) • Normal Charging Speed - Qi enabled Google , Huawei , Sony , Nokia , LG , Xiaomi - 5W Charge • Charges Through - All non-metalic surfaces wood , plastic , granite , quartz , marble glass • Product Dimensions - 182mm x 112mm x 20mm (7.17’ x 4.41’ x 0.79’) • Power cable length - 1.
• LED Indication Status LED Power Off Off Power On On System Fault (OTP,OCP,UVP,OVP, Phone Protect Mode) Blink • System Fault - Under Voltage Protect (UVP) - Over Voltage Protect (OVP) - Over Current Protect (OCP) - Over Temp Protect (OTP) - Phone Protect Mode : Action when the phone is positioned closer than the Charging distance (under 18mm) ※ System Fault can be used again after removing cause of occurrence, turning power off and on.
Warranty KEW LABS warrants to the purchaser that your product shall be free from defects in material and workmanship for the length of time, identified on your product package and/or at www.kewlabstech.com under the warranty specification for your product, from the date of purchase. This warranty is non transferable and is limited to original purchaser and the country it was purchased in.
Safety instruction • Avoid contact with water and do not submerge • Avoid extreme temperatures • Avoid dropping. • Use original or certified cables. • Do not clean with corrosive substances or oils. • Do not disassemble. • This product is in compliance with the radio interference requirements of the European Community. • Electronic adapters are recyclable waste and must not be disposed of in the house- hold waste.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
