Item #1000 000 000 Model #GFHD48 USE AND CARE GUIDE THD PRODUCT NAME: 48in Rectangular Gas Fire Pit Concrete Finish Questions, problems, missing parts? Before returning to the store, call Hampton Bay Customer Service 8 a.m. - 7 p.m., EST, Monday – Friday, 9 a.m. – 6 p.m., EST, Saturday 1-855-HD-HAMPTON HAMPTONBAY.
SAFETY INFORMATION Before you assemble or operate this unit, please ca refully read this entire manual. Failure to do so may r WARNING • The installation of this unit must adhe re to local codes or either the National Fuel Gas Code, ANSI Z223. 1/NFPA54, OR CAN/CGA-B149.1, National Gas and Propane Installation Code. • THIS UNIT IS INTENDED FOR OUTDOOR USE ON LY! This product shall be used outdoors, in a ventilated space and shall not be used in any enclosed a rea.
• Combustible material should not be within 72 inches of the top of the unit, or within 48 inches around the entire unit. • Keep the appliance area clear and free fr vapors and liquids. • ning, turn the gas valve off. Wait 5 minutes before repeating the initial • Do not add water into the unit. • Do not operate unit if any part has been under water.
SAFETY INFORMATION Only use the regulator and hose assembly provided with this unit. Inspect the bur ner before use of this unit. If the bur ner shows any kind of damage, do not operate the appliance. NOTE: You must follow all steps to properly assemble this heating item. Make sure the gas valve is turned “OFF” before assembling. Do NOT attempt to assemble without proper tools. Min. Clearance 48 in (121.9 cm) Min. Clearance 48 in (121.9 cm) Min. Clearance 48 in (121.
CONTENTS I E D A B C F G H Item Description Qty A Lid B Lava Rocks 1 1 box C Body 1 D Tank Holder 1 E Battery 1 F Control Knob (preassembled) 1 G H I Electronic Igniter (preassembled) Adjust Foot Protective Cover for Gas Cylinder 1 4 1 5 HAMPTONBAY.COM Please contact 1-855-HD-HAMPTON for further assistance.
ASSEMBLY INSTRUCTIONS 1.Turn over the body(C) and assemble 4pcs adjust feet(H) into bottom. H C 2. Check that the cont rol knob (F) for the gas supply system is tu rned to the “OFF” position before starting any assembly. F OF HI F 3. Put the 20 lb. p ropane gas tank (not included) into the tank holder (D). Turn the wing sc rew on the outside of the tank holder (D) clockwise to tighten the tank into the tank holde r. D DANGER Propane tank must be a minimum of 60 inches away at all times.
4. Turn the cylinder valve on the tank clockwise to close the p ropane tank. Attach the p reassembled regulator from the body (C) to the cylinder valve by turning the regulator coupling nut clockwise. Make su re it is fastened securely and tighten connections by hand only. PRESSURE RELIEF VALVE CYLINDER VALVE BLACK COUPLING NUT turn clockwise to connect BLEED-OFF VALVE turn clockwise to reseal REGULATOR 5.
OPERATION Before performing a leak test, be su re that no sparks can occur and you a re in a spacious outdoor area. Connect the propane gas tank to the regulator and turn the valve on the unit to the “o ff” position. Brush a soap and water mixtur e on all connections. Turn the gas supply on; if bubbles occur on any connection the re may be a leak. If you smell gas or a leak is discove red tu rn the gas valve o ff, disconnect p ropane gas tank and do not use the appliance until the leak is repai red.
MAINTENANCE • Before performing any maintenance always disconnect propane gas tank. • Keep the heating item free and clear from combustible materials. • Visually inspect burner for obstructions and keep tank enclosure free and clear from debris. • Use a soft brush to get rid of the mild stains, loose dirt and soil after the burner and pumice stones/ lava rocks/LavaGlass™ are completely cooled down. Wipe down with a soft cloth.
TROUBLESHOOTING Problem Heating unit won’t light Burner won’t light while using a match Cause Solution Igniter pin and burner are wet Dry off with a soft cloth Igniter battery is incorrectly inserted Check which direction the battery is inserted Igniter pin is broken Contact Bond Manufacturing for a replacement part Electrode wire is loose or disconnected Reconnect wire to the igniter box located inside the fire table behind the igniter box Electrode wire is shorting between valve and igniter p
CARE AND MAINTAINCE Service: Repair gas passages and associated components should be done only by a qualified service person. Caution: Always allow heater to cool before attempting service. 11 HAMPTONBAY.COM Please contact 1-855-HD-HAMPTON for further assistance.
Questions, problems, missing parts? Before returning to the store, call Hampton Bay Customer Service 8 a.m. – 7 p.m., EST, Monday – Friday, 9 a.m. – 6 p.m., EST, Saturday 1-855-HD-HAMPTON HAMPTONBAY.COM Retain this manual for future use.
