Installation Guide
Installation
INSTALLATION AND OPERATION
SMART WI-FI REMOTE CONTROL
Safety Information
Warranty
CAUTION: Incorrect wire
connections will damage
this receiver.
The supplier warrants the remote control and receiver to be free from defects in
workmanship and material present at time of shipment from the factory for a period
of one year after the date of purchase by the original purchaser. We agree to correct
such defects without charge or at our option replace with a comparable or superior
model if the product is returned. To obtain warranty service, you must present a
copy of the receipt as proof of purchase. All costs of removing and reinstalling the
product are your responsibility. Damage to any part such as by accident or misuse or
improper installation or by afxing any accessories, is not covered by this warranty.
Servicing performed by unauthorized persons shall render the warranty invalid. There
is no other express warranty. Home Depot hereby disclaims any and all warranties,
including but not limited to those of merchantability and tness for a particular
purpose to the extent permitted by law. The duration of any implied warranty which
cannot be disclaimed is limited to the time period as specied in the express warranty.
Some states do not allow a limitation on how long an implied warranty lasts, so the
above limitation may not apply to you. The retailer shall not be liable for incidental,
consequential, or special damages arising out of or in connection with product use
or performance except as may otherwise be accorded by law. Some states do not
allow the exclusion of incidental or consequential damages, so the above exclusion
or limitation may not apply to you. This warranty gives specic legal rights, and you
may also have other rights which vary from state to state. This warranty supersedes
all prior warranties. Shipping costs for any return of product as part of a claim on the
warranty must be paid by the customer.
Contact the Customer Service Team at 1-877-592-5233 or visit
www.HomeDepot.com/hubspace.
Pre-Installation
TOOLS REQUIRED
Step
ladder
Part Description Quantity
A Receiver 1
B Remote control 1
C Plastic wire connector 6
D AAA battery (1.5V) 2
E Silicone rubber plug 1
F Wall cradle 1
G Wall cradle screw 2
H Plastic anchor 2
PACKAGE CONTENTS
IMPORTANT: This product
and/or components
are governed by one or
more of the following
U.S. Patents: 5,947,436;
5,988,580; 6,010,110;
6,046,416, 6,210,117 and
other patents pending.
1
NOTE: The frequencies on your receiver and hand unit have
been preset at the factory. Before installing the receiver, make
sure the dip switches on the receiver and hand unit are set
to the same frequency. The dip switches on the hand unit are
located inside the battery compartment.
Setting the code on the remote control
Application Set-Up
• Remove the remote control
(B) battery cover by pressing
firmly on the arrow and sliding
the cover off.
• Slide the dip switches (ZZ)
to your choice of either up
or down. The factory setting
is up.
• Slide the dip switches (ZZ) on
the receiver (H) to the same
position as set on the remote
control (B).
• Install two 1.5V batteries
(included).
• Replace the battery cover on
the remote control (B).
• Insert the silicone rubber
stopper (OO) into the hole on
the receiver (A) to cover the
dip switches.
1
Operating the remote control
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
--Consult the dealer or an experienced radio/TV technician for help.
CAUTION:
Any changes or modications not expressly approved by the grantee of this device could void the
user’s authority to operate the equipment.
FCC ID: 2AQZU-18016
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Item #xxxx xxx xxx
Model #76278
CAUTION: To reduce the risk
of re or injury, do not use this
product in conjunction with any
variable (rheostat) wall control.
NOTE: The battery will weaken
with age and should be
replaced before leaking takes
place as this will damage
the hand unit. Dispose of the
used battery properly, keep
the battery out of the reach of
children.
WARNING: To avoid possible
electrical shock, turn the
electricity off at the main
fuse box before wiring. If you
feel you do not have enough
electrical wiring experience,
contact a licensed electrician.
2
Installing the receiver
WARNING: To reduce the risk of re or electric shock, remember
to disconnect power. The electrical wiring must meet all local and
national electrical code requirements. The electrical source and fan
must be 110/120 volt, 60Hz. Do not use this product in conjunction
with any variable wall control. Incorrect wire connection can damage
this receiver.
CAUTION: If fan or house wires are a different color, have this unit
installed by a licensed electrician.
CAUTION: Do not install in a damp location or immerse in water (for
indoor use only). Do not pull on or cut leads shorter. Do not drop or
bump the unit.
Installation (continued)
NOTE: You must set ceiling fan to high speed and light kit (if any) to
the on position using the pull chains (if applicable) before operating
remote control.
NOTE: For better performance with the WIFI system, the WIFI antenna
must be mounted to the ceiling outside of the fan’s ceiling canopy.
• Position the house supply wires (AAA) to one side of the slide-on
mounting bracket; position the fan wires (BBB) to the opposite side.
• Insert the narrow end of the receiver (as shown, flat side towards the
ceiling) into the slide-on mounting bracket until it rests on top of the
ball/downrod assembly.
Installation (continued)
3
Wiring the receiver to the household wiring
IMPORTANT: Use the wire connecting nuts (C) supplied with your fan.
Secure the connectors with electrical tape and ensure there are no
loose strands or connections.
WARNING: Each wire nut supplied with this fan is designed to
accept up to one 12-gauge house wire and two wires from the fan.
If you have larger than 12-gauge house wiring or more than one
house wire to connect to the fan wiring, consult an electrician for
the proper size wire nuts to use.
• Spread the wires apart so that the green and white wires are on one side
of the outlet box and the black wire is on the other side.
• Connect the green fan wires to the household ground wire (this may be a
green or bare wire) using a wire connecting nut (C).
• Connect the receiver black (or red) wire to the household black (hot) wire
using a wire connecting nut (C).
• Connect the receiver white wire to the household white wire (neutral)
wire using a wire connecting nut (C).
• Secure each wire connecting nut using electrical tape.
WARNING: To avoid possible electrical shock, turn the electricity
off at the main fuse box before wiring. If you feel you do not have
enough electrical wiring knowledge or experience, contact a
licensed electrician.
Wiring the fan to the receiver
• Connect the fan motor white wire
to the receiver white wire using a
wire connecting nut (C).
• Connect the fan motor black wire
to the receiver black wire using a
wire connecting nut (C).
• Connect the fan motor blue wire
to the receiver blue wire using a
wire connecting nut (C).
• Secure each wire connecting nut
using electrical tape.
• Turn the wire connecting nut (C)
upward and push the wiring into
the outlet box (MM).
4
IMPORTANT: Use the wire connecting nuts (C) supplied with your
fan. Secure the connectors with electrical tape and ensure there are
no loose strands or connections.
Operating Your Remote Control
Mounting the transmitter to the wall
1
• Slide the screw cover plate up to remove it from the wall cradle (F).
• Position the wall cradle (F) in the desired position and attach it to the wall
using the included wall cradle screws (G).
• Slide the screw cover plate back onto the wall cradle to conceal the screws.
Wire
cutter
Electrical tape
Phillips
screwdriver
D
C
F
E
A
B
G
H
Installation (continued)
Read and save these instructions
1. The power supply to the remote
control receiver should be connected
through a mains switch, i.e. existing
wall switch.
2. Disconnect from power supply at
breaker box or wall switch before
working on remote control receiver or
ceiling fan.
3. Install receiver into the mounting
bracket/ canopy of the fan to ensure
proper protection.
4. This unit is to be used for the control of
ceiling fan and in a AC110/120V 60Hz
power supply only.
5. Do not install in damp locations or
immerse in water. (For indoor use only.)
6. Do not pull on or cut leads shorter.
7. Do not drop or bump the unit.
8. Do not mix old and new batteries.
9. Do not mix alkaline, standard (carbon-
zinc), or rechargeable (ni-cad, ni-mh,
etc.) batteries.
Controller model: TR240B
WIFI antenna mount
outside of the canopy
A
BBB
AAA
A
Black
Black
Green (or Bare)
Green
Outlet Box
Receiver
Antenna
White
Receiver (B)
C (x3)
DIP
Antenna
WIFI
Screw cover plate
G
F
Power ON/OFF: Press and release the power
button to turn the fan and light on or off.
Fan speed: LEDs on the fan speed button will
illuminate to the corresponding speed.
Press and release 1 time: turns the fan speed
to 4.
Press and release 2 times: turns the fan
speed to 3.
Press and release 3 times: turns the fan
speed to 2.
Press and release 4 times: turns the fan
speed to 1.
Press and release 5 times: turns the fan off.
Light ON/OFF:
Press and release the button to turn the light
on or off.
Press and hold the button to activate the
dimmer function.
Comfort Breeze: Press the button to enable
Comfort Breeze; this will change your fan
randomly, simulating a relaxing breeze. To
cancel this features press fan speed button or
power button.
Timer:
While the fan is on press 1 time-turns on a 2 hour run timer.
While the fan is on press 2 times-turns on a 4 hour run timer.
While the fan is on press 3 times-turns on a 8 hour run timer.
□ Download the Hubspace™ app from the App
Store or the Google Play Store to your mobile
device.
□ Launch the app.
□ To register, enter your email address and a
password. Or, login if you already have an
account.
□ Bluetooth access is required for device setup.
Getting started
1
□ This Hubspace device requires a 2.4GHz Wi-Fi channel.
□ Most routers provide a 2.4 GHz WiFi channel.
□ Hubspace only shows WiFi networks that your device can use.
□ If you do not see your Wi-Fi network name when you attempt to connect your
device, please check your router settings.
Verify your network
2
□ In the Hubspace app, tap the plus sign in the upper right corner.
□ Scan your product’s QR code. You can nd a copy of the QR code on the device
itself and in the Quick Start Guide.
Scan problem?
If the QR code cannot be scanned for some reason, you can enter the code
manually. Tap Enter Code and follow the instructions.
□ Connect your device to power and follow the instructions on screen.
(For lighting and fan products only)
Add a device
3
If you are unable to access the QR code for your light, you can put it into
discovery mode with the following sequence:
□ Switch the device off and on 5 times. The light will pulse to show that it can
now be discovered.
□ In the Hubspace app, tap the plus sign in the upper right corner and follow
the instructions to discover devices. More than one device can be added at
a time using this method.
Set up your voice assistant
4
□ In the Hubspace app, tap the Hubspace button.
□ Select the Integrations tab, choose your voice assistant and follow the
instructions.
NOTE: For more information on smart remote set up, please refer to the
quick start guide located in the remote pack.
Questions, problems, missing parts? Before returning to the store,
call Hubspace Customer Service
8 a.m. - 7 p.m., EST, Monday - Friday, 9 a.m. - 6 p.m., EST, Saturday
1-877-592-5233
HOMEDEPOT.COM/HUBSPACE
We appreciate the trust and condence you have placed in Hampton Bay through
the purchase of this remote control. We strive to continually create quality
products designed to enhance your home. Visit us online to see our full line of
products available for your home improvement needs.
Thank you for choosing Hampton Bay!
B
A
ZZ
1 2 3 4
ON
D O
1
2 3 4
ON
D O
1 2 3 4
ON
OO
1 2 3 4
ON
DIP
NOTE: The switch marked “O/D” controls the dimming function
of the lights. If you are using non-dimmable bulbs, use a
ballpoint pen or small screwdriver to set the switch to “O” to
disable the dimming function. If you are using dimmable bulbs,
set the switch to “D” to enable the dimming function.
NOTE: The battery will weaken with age and should be replaced
before leaking takes place, as battery leakage damages the
hand unit. Dispose of the used battery properly and keep the
battery out of the reach of children.
Outlet box
in the ceiling
(MM)
Green
1 2 3 4
ON
DIP
Blue
Black
White
C (x3)
Problem Solution
My hubspace device is not
connecting to Wi-Fi.
Make sure your device is connected to a power source.
Your Internet connection or Wi-Fi network may be down.
My device cannot nd any
Wi-Fi networks.
Make sure you have a 2.4GHz capable Wi-Fi network within
range of the device you are trying to add.
My device is in a location that
does not have Wi-Fi. Can I still
use it with the Hubspace app?
Yes:
Use the app on a phone with an Internet connection like LTE.
The phone must be within Bluetooth range of your
Hubspace device.
I cannot nd the QR code. Look for it where other stickers are on the product. A
copy of the QR code is also included in your device’s
documentation.
The QR code has become
damaged. How do I add the
device?
Under the QR code are numbers. You can enter those in
manually instead of scanning the code.
How do I reset the device? Remove the device from your account, then add it back.
Devices also reset when they transfer to a new account.
A device is on another
account. How do I transfer it?
Scan the QR code and it will transfer to your account.
My device is ofine for long
periods of time.
Make sure your Wi-Fi signal strength is sufcient. You
may need to move your router, use mesh Wi-Fi, or Wi-Fi
extenders.
The device is on and I scanned
the QR code, but the app
cannot connect to it.
Turn off Bluetooth on your phone and turn it back on. Then,
scan the QR code.
Can I scan the same QR code
to add multiple products?
No. Each product has a unique QR code.
Troubleshooting
NOTE: Plastic anchors (H) are included for extra support. The included
screws (G) are designed to screw easily into the wall. If you would like
a more permanent or secure hold, install the wall anchors (H) prior to
attaching the wall cradle to the wall.