Palisades 52 in Ceiling Fan Owner’s Manual Palisades Ventilador de Techo de 1,32 m Manual del Propietario
52” Palisades Ceiling Fan by Hampton Bay Accu-arm™ for Accurate and Easy Installation Thank you for purchasing this Hampton Bay ceiling fan. This product has been manufactured with the highest standards of safety and quality. The finish of this fan is weather resistant, but over time will naturally weather and fade. Table of Contents Safety Rules................................... 1 Steeper Blade Pitch for Greater Air Movement Unpacking Your Fan.....................
READ AND SAVE THESE INSTRUCTIONS 1. To reduce the risk of electric shock, insure electricity has been turned off at the circuit breaker or fuse box before beginning. 2. All wiring must be in accordance with the National Electrical Code ANSI/NFPA 70-1999 and local electrical codes. Electrical installation should be performed by a qualified licensed electrician. 3. WARNING: To reduce the risk of electrical shock or fire, do not use this fan with any solid-state speed control device.
1 4 7 8 a 2 9 3 5 6 10 Unpack your fan and check the contents. You should have the following items: 1. 2. 3. 4. 5. 6. Mounting Plate (inside canopy) Canopy Ball/Downrod Assembly Fan Motor Assembly Light Kit Decorative Motor Collar Cover b 7. Blades (5) 8. Blade Bracket 9. Glass Bowl 10. Bulbs (3) IMPORTANT: THIS PRODUCT AND/OR COMPONENTS ARE COVERED BY ONE OR MORE OF THE FOLLOWING U.S. PATENTS: 5,947,436; 5,988,580; 5,971,573; 6,010,306; 6,039,541; 6,046,416 AND OTHER PATENTS PENDING. 2.
Tools Required Phillips screw driver, straight slot screw driver, adjustable wrench, step ladder, and wire cutters. Figures 1, 2, and 3 are examples of different ways to mount the outlet box. Mounting Options Figure 3 If there isn’t an existing outlet box, then read the following instructions. Disconnect the power by removing fuses or turning off circuit breakers. Secure the outlet box directly to the building structure. Use appropriate fasteners and building materials.
Hanging the Fan REMEMBER to turn off the pow- er. Follow the steps below to hang your fan properly. NOTE: This ceiling fan is supplied with two types of hanging assemblies; the standard ceiling installation using the downrod with ball and socket mounting, and the “close-toceiling” mounting. The “close-to-ceiling” mounting is recommended in rooms with less than 8-foot ceilings or in areas where additional space is desired from the floor to the fan blades.
Mounting Screws (Supplied With Outlet Box) UL Listed Outlet Box Hook Slide Mounting Plate Over Screw Heads Ceiling Mounting Plate 120V Wires Motor Wires Ball/Downrod Canopy Assembly Canopy Ring Locking Pin Motor Collar Cover Pin in Locked Position Hanger Pin Motor Collar Tighten Screws Figure 7 “Close-to-Ceiling” Mounting 1. Remove the canopy ring from the canopy by turning the ring to the right until it unlocks (Figure 5). 2.
Installing Fan to the Outlet Box WHEN MOUNTING ON A SLOPED CEILING, MAKE SURE THE MOUNTING PLATE SLOTS ARE ON THE LOWER SIDE BY SLIDING THE MOUNTING PLATE FROM THE TOP DOWN. 1. Pass the 120-volt supply wires through the center hole in the ceiling mounting plate as shown in Figure 7. 2. Attach the ceiling mounting plate on the outlet box by sliding the mounting plate over the two screws provided with the outlet box. When using close-to-ceiling mounting, it is important that the mounting plate be level.
BLACK WHITE SUPPLY CIRCUIT BLUE BLACK WHITE GREEN Outlet Box Green Grounding Lead Ground to Downrod ELECTRICAL DIAGRAMS ARE FOR REFERENCE ONLY. OPTIONAL USE OF ANY LIGHT KIT SHALL BE UL LISTED AND MARKED SUITABLE FOR USE WITH THIS FAN. Finishing the Fan Installation STANDARD CEILING MOUNTING WHEN USING THE STANDARD BALL/DOWNROD MOUNTING, THE TAB IN THE RING AT THE BOTTOM OF THE MOUNTING PLATE MUST REST IN THE GROOVE OF THE HANGER BALL.
CLOSE-TO-CEILING MOUNTING 1. Carefully unhook the fan from the mounting plate and align the locking slots of the ceiling canopy with the two screws in the mounting plate. Push up to engage the slots and turn clockwise to lock in place. Immediately tighten the two mounting screws firmly. LOCKING SLOTS OF CEILING CANOPY ARE PROVIDED ONLY AS AN AID TO MOUNTING. DO NOT LEAVE FAN ASSEMBLY UNATTENDED UNTIL ALL FOUR CANOPY SCREWS ARE ENGAGED AND FIRMLY TIGHTENED. 2.
Blade Balancing All blades are grouped by weight. Because natural woods vary in density, the fan may wobble even though the blades are weight matched. The following procedure should correct most fan wobble. Check after each step. 1. Check that all blades are securely mounted to the blade brackets. 2. Make sure the blade brackets are not bent or out of position and ensure the blade tips are even. Run the fan for ten minutes.
Fan Without Light Kit 1. In order to use the fan without the light kit, remove the switch cup cover from the top of the light kit by removing the center hex nut inside the switch cup cover, and then thread the switch cup cover off of the threaded nipple on the top of the light kit. 2. Press the plastic plug (provided) into the center hole of the switch cup cover. 3. Loosen the three serrated head screws on the switch cup cover.
Turn on the power and check the operation of the fan. The pull chain controls the fan speeds as follows: 1 pull - High, 2 pulls - Medium, 3 pulls - Low and 4 pulls - Off Speed settings for warm or cool weather depend on factors such as room size, ceiling height, number of fans, and so on. The reverse switch controls the direction: forward (switch down) or reverse (switch up). WAIT FOR FAN TO STOP COMPLETELY BEFORE SETTING THE REVERSE SWITCH TO REVERSE THE DIRECTION OF BLADE ROTATION.
Care of Your Fan Troubleshooting 1. Because of the fan’s natural movement, some connections may become loose. Check the support connections, brackets, and blade attachments twice a year. Make sure they are secure. (It is not necessary to remove fan from ceiling.) Fan will not start 1. 2. Check main and branch circuit fuses or breakers Check line wire connections to the fan and switch wire connections in the switch housing. CAUTION: Make sure main power is off. Fan sounds noisy 1. 2.
FAN SIZE SPEED 52” VOLTS AMPS WATTS RPM CFM Low 120 0.25 14.7 70 2160 Med 120 0.37 31.0 110 3498 High 120 0.52 62.1 165 5415 NET WEIGHT GROSS WEIGHT CUBE FEET 24.4 Lbs (11.1 kg) 27.9 Lbs (12.7 kg) 2.3’ These are approximate measures. They do not include Amps and Wattage used by the light kit. Distributed by Your Other Warehouse LLC 12100 Little Cayman Dr. Baton Rouge, LA 70809 Vendor number: 219030 Specifications 13.
Hampton Bay Lifetime Limited Warranty Lifetime Warranty on Motor Hampton Bay warrants the fan motor to be free from defects in workmanship and material present at time of shipment from the factory for a lifetime after the date of purchase by the original purchaser.
