Installation Guide

ManualsBrandsHampton Bay ManualsKitchenChateau Deville 2-Light Walnut Semi-Flush Mount Ceiling Fixture

INSTALLATION INSTRUCTIONS

NEW 07/02/2004

WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.

Fig. 1

Fig. 2

HANGING THE FIXTURE (Fig. 1)

1. Carefully remove the fixture from the carton and check

that all parts are included as shown in the illustration.

2. Shut off power at the circuit breaker and remove old

fixture including the crossbar.

3. Attach the Circular Strap (B) to the Outlet Box (A) using

the two screws (C). The side of the Circular strap

marked “GND” must face out.

4. Thread the two Threading Studs (D) into the predrilled

holes in the Circular Strap(B) spaced the same

distance apart as the hole in the Canopy (E) on Fixture

Body (G)

CONNECTING THE WIRES (Fig. 2)

5. At this point, connect the electrical wire as shown in

figure 2, making sure that all wire connectors are

secured. If your outlet has a ground wire (green or bare

copper), connect the fixtures Ground Wire to it.

Otherwise, connect the fixture Ground Wire directly to

the crossbar using the Green Screw provided.

FINISHING THE INTALLATION (Fig. 1)

6. Secure the Canopy (E) by placing it over Threading

Studs (D) and secure against ceiling with Knurled

Knobs (F).

7. Thread Nipple (H) to the bottom of Fixtures Body (G).

8. Install the light bulb in accordance with the fixture’s

specifications. (DO NOT EXCEED THE MAXIMUM

WATTAGE RATING!)

9. Slide Glass Shade (I) upwards over Nipple (H) and

secure with Finial (J) as shown in Fig.1.

Your installation is now complete. Return power to the

junction box and test the fixture.

FIXTURE

WIRES

Black or

Smooth

USE

WIRES

Black

(Hot)

FIXTURE

WIRES

White or

Ribbed

USE

WIRES

White

(Neutral)

FIXTURE

WIRES

Bare

Copper

(Ground)

USE

WIRES

Green

(Ground)

LA-835E/S

Note: Illustration (Fig. 1) on this manual is for

installation purposes only. It may or may not be

identical to the fixture purchased.

In the event that you should have any installation

question or are missing parts, please contact

Customer Service. Customer service may be reached

weekdays a 1-800-527-0998 between the hours o

8:00am and 5:00pm PST (Pacific Standard Time).

Summary of content (2 pages)

PAGE 1
INSTALLATION INSTRUCTIONS NEW 07/02/2004 WARNING! S H U T P O W E R O F F AT F U S E O R C I R C U I T B R E A K E R . HANGING THE FIXTURE (Fig. 1) 1. Carefully remove the fixture from the carton and check that all parts are included as shown in the illustration. Fig. 1 A 2. Shut off power at the circuit breaker and remove old fixture including the crossbar. B C D 3. Attach the Circular Strap (B) to the Outlet Box (A) using the two screws (C).
PAGE 2
INSTRUCCIONES PARA LA INSTALACION Nueva 07/02/2004 ADVERTENCIA! CORTE LA CORRIENTE DESDE EL FUSIBLE O EL INTERRUPTOR ENSAMBLAJE DE LA LAMPARA (Fig. 1) 1. Desempaque cuidadosamente su nueva lampara y coloque todas las partes en una superfice despejada.Tenga cuidado de no perder las partes pequeñas que son necesarias para la instalacion. 2. Corte la corriente en el circuito principal y quite la lampara vieja incluyendo la barra transversal. 3.