77 643 Everbilt 54 Everbilt 1,37
Everbilt by Hampton Bay ®
54 Everbilt Thank you for purchasing our ceiling fan. This product has been manufactured with the highest standards of safety and quality. Ceiling Fan by Hampton Bay Date Purchased Store Purchased Table of Contents Safety Rules . . . . . . . . . . . . . . . . . . . . 1 ETL Model No. 177 643 Unpacking Your Fan . . . . . . . . . . . . . . 2 Installing Your Fan . . . . . . . . . . . . . . . 3 Installing the Light Kit. . . . . . . . . . . . . 8 Serial No. Operating Your Fan . . . . . . . . . . . . . .
Safety Rules - Read and Save These Instructions 1. To reduce the risk of electric shock, insure electricity has been turned off at the circuit breaker or fuse box before beginning. 2. All wiring must be in accordance with the National Electrical Code “ANSI/NFPA 70-1999” and local electrical codes. Electrical installation should be performed by a qualified licensed electrician. 3. WARNING: To reduce the risk of electrical shock or fire, do not use this fan with any solid-state fan speed control device.
Unpacking Your Fan Unpack your fan and check the contents. You should have the following items: 3 4 1 10 5 6 7 11 8 12 B C D E F 13 9 2 Unpack your fan and check the contents. You should have the following items: 1. 2. 3. 4. 5. 6. 7. 8. 9. A Blades (5) Hanger bracket (1) Canopy (1) Canopy cover (1) Ball/downrod assembly (1) Scroll (3) Scroll bracket (1) Coupling cover (1) Fan motor assembly (1) WARNING DO NOT INSTALL OR USE FAN IF ANY PART IS DAMAGED OR MISSING.
Installing Your Fan Tools Required Provide Strong Support Figures 1~3 are examples of different ways to mount the outlet box. Phillips screwdriver, straight slot screwdriver, step ladder and wire cutters. Recessed Outlet Box Mounting Options Outlet Box If there isn't an existing UL listed mounting box, then read the following instructions. Disconnect the power by removing fuses or turning off circuit breakers. Secure the outlet box directly to the building structure.
Hanging the Fan 7. Slip canopy cover and canopy onto reinstall REMEMBER to turn off the power. Follow the downrod. (Figure 11) Carefully hanger ball onto downrod. Make sure that steps below to hang your fan properly: cross pin is in correct position, set screws are tighten and wires are not twisted. 1. Secure the hanger bracket to the ceiling outlet box with the screws and washers provided with your outlet box. (Figure 5) 2.
Making the Electrical Connections Remember to shut off the power. Follow the steps below to connect the fan to your household wiring. Use the wire connecting nuts supplied with your fan. Secure the connectors with electrical tape. Ground Conductor BLUE BLACK LIGHT KITS ARE AVAILABLE AT YOU HAMPTON BAY RETAILER. THE FAN IS ALREADY WIRED TO SUPPORT THE LIGHT KIT OPTION. GREEN Outlet Box NOTE Figure 12 WHITE BLACK SUPPLY CIRCUIT WHITE Registration slot 5.
Light WHITE Ground Conductor SUPPLY CIRCUIT BLACK WHITE BLACK SUPPLY CIRCUIT Ground Conductor Outlet Box Ground to Downrod GREEN Green Ground Lead BLUE GREEN WHITE BLUE BLACK Light Switch BLACK WHITE Outlet Box Fan Green Ground Lead Ground to Downrod Finishing the Installation 1. Tuck connections neatly into ceiling outlet box. 2. Remove one screw from the hanger bracket and loosen the other screw around 1/4″. 3. Align the canopy up to ceiling and over the loose screw.
Attaching the Fan Blades 1. Attach the fan blades to the motor assembly using the screws and fiber washer provided, tighten screws securely.(Figure 17) Blade balancing The following procedure should correct most fan wobble. Check after each step. 2. Align motor holes to blade and secure with screws provided, tighten screws securely. Repeat procedure with remaining blades. (Figure 17) Touching ceiling Blade Figure 18 Figure 17 7 Fiber Washers Screws 2.
Installing the light kit REMEMBER to disconnect the power. The fan blades must already be attached to the fan. Your fan and light kit though pre-wired have been disassembled at the factory to ease in shipping. Please follow these steps to complete the installation of your fan and light. TO REDUCE THE RISK OF FIRE DO NOT EXCEED MAXIMUM WATTAGE RATING. ATTENTION: The Energy Policy Act of 2005 requires this fan to be equipped with a 190 watt limiting device.
Operating your fan NOTE WAIT FOR FAN TO STOP BEFORE CHANGING THE SETTING OF THE SLIDE SWITCH. Turn on the power and check the operation of your fan. There are three pull chains available in your fan: Cool weather - (Clockwise direction) An upward airflow moves warm air off the ceiling area. (Fig. 22) This allows you to set your heating unit on a lower setting without affecting your comfort. 1.
Care of Your Fan Troubleshooting Here are some suggestions to help you maintain your fan. 1. Because of the fan's natural movement, some connections may become loose. Check the support connections, brackets, and blade attachments twice a year. Make sure they are secure. (It is not necessary to remove fan from ceiling.) 2. Clean your fan periodically to help maintain its new appearance over the years. Do not use water when cleaning. Use only a soft brush or lint-free cloth to avoid scratching the finish.
Specifications FAN SIZE SPEED VOLT S AMPS LOW 54’’ (1,37 m) MED 120 HIGH WATT S RPM 0.22 10.2 60 1705 0.392 32.2 112 3570 0.535 63.8 160 5172 These are approximate measures. They do not include Amps and Wattage used by the light kit. Distributed by Your Other Warehouse, LLC 12100 Little Cayman Dr. Baton Rouge, LA 70809 11 CFM N.W. G.W. 9.4kgs 20.68lbs 11kgs 24.2lbs C.F. 1.
Lifetime Limited Warranty (lifetime warranty on motor) The Hampton Bay warrants the fan motor to be free from defects in workmanship and material present at time of shipment from the factory for a period of lifetime after the date of purchase by the original purchaser.
