INSTRUCTIONS MANUAL 2-LIGHT SEMI-FLUSH LIGHT FIXTURE GRACE COLLECTION HOME DEPOT SKU# 515-193 (UPC# 802513146929) ANTIQUE BRASS FINISH 1
Thank you for purchasing this Hampton Bay interior Semi-Flush light fixture. This product has been manufactured with the highest standards of safety and quality. FEATURES: 1. Easy to install. 2. Two light Semi-Flush light fixture with Antique Brass Finish and Seeded with waves Glass Shade. 3. For energy savings this fixture has been engineered to safely use a Self Ballasted Compact Fluorescent Bulb in place of an incandescent bulb.
CAUTION: 1. Before starting installation of this fixture or removal of a previous fixture, disconnect the power by turning off the circuit breaker or by removing the fuse at the fuse box. 2. CONSULT A QUALIFIED ELECTRICIAN IF YOU HAVE ANY ELECTRICAL QUESTIONS. If you have any non-electrical questions about this fixture, please call our Customer Service Team at 1-877-527-0313 or visit www.homedepot.com. Please reference your SKU (515-193) or UPC (802513146929). 3.
PARTS INCLUDED FOR ASSEMBLY AND INSTALLATION (parts are not to scale): Parts Plastic Washer 2 Metal washer 2 G5/32 inch Hex 2 Wire Connector 3 G3/8 inch Hex Nut 1 Outlet Box Screw 2 Green Ground Screw 1 Threaded Pipe 1 Support Screw 2 Cap Nut 2 Mount Strip 1 Glass Shade 4 Qty 1 Finial 1 Cap 1 Fixture Body 1
ASSEMBLY AND INSTALLATION: WHITE SUPPLY WIRE GROUND SUPPLY WIRE WHITE WIRE SUPPORT SCREW MOUNTING STRIP OUTLET BOX SCREW OUTLET BOX BLACK SUPPLY WIRE WIRE CONNECTOR BLACK WIRE GREEN GROUND SCREW G5/32 INCH HEX NUT BARE COPPER GROUNDING WIRE CANOPY CAP NUT ARM SOCKET ASSEMBLY BUSHING THREADED PIPE METAL WASHER PLASTIC WASHER GLASS SHADE PLASTIC WASHER METAL WASHER G3/8 INCH HEX NUT CAP FINIAL 5
ASSEMBLY AND INSTALLATION INSTRUCTIONS: 1. Shut down the main electrical supply from the fuse box or circuit breaker in your house or building. 2. Tighten support screws (long) full turns into the inside mounting hole of mounting strip (to be fully tightened later) secure by G5/32 inch hex nut. This support screws (long) should extend long enough to protrude through the canopy when it is mounted.(Adjust as needed) 3. Fasten the mounting strip onto outlet box using two outlet box screws (short). 4.
TROUBLESHOOTING: Lights will not turn on. Fuse blows or circuit breaker trips when light is turned on. Possible Cause Corrective Action 1. P ow er is off. 1. Make s ure pow er s up ply is on. 2. F ault y s w it ch. 2. T es t or rep lace s w it ch. 3. Faulty wire connection. 3. Check wiring. 1. Crossed wires or power wire is grounding 1. Check wire connections. out. PRODUCT MAINTENANCE: 1.
MANUAL DE INSTRUCCIONES LÁMPARA DE 2-LUCES SEMI-INCRUSTADA AL TECHO COLECCIÓN GRACE HOME DEPOT SKU# 515-193 (UPC# 802513146929) ACABADO METAL ENVEJECIDO 8
Gracias por comprar esta Lámpara Semi-embutida al Techo para interiores de Hampton Bay. Este producto ha sido manufacturado teniendo en cuenta los estándares más altos de calidad y seguridad. CARACTERÍSTICAS: 1. Fácil de instalar. 2. Lámpara de Dos luces Semi-embutida al techo con acabado en Bronce Antiguo y Pantalla de Cristal Facetado en Olas. 3. Para ahorrar energía este artefacto ha sido diseñado para usar una bombilla compacta fluorescente con su propio balastro en lugar de una bombilla incandescente.
PRECAUCIÓN: 1. Antes de comenzar la instalación de este artefacto o de desmontar un artefacto, desconecte la fuente de electricidad apagando el interruptor de electricidad o sacando el fusible de la caja de fusibles. 2. CONSULTE A UN ELECTRICISTA CALIFICADO SI USTED TIENE CUALQUIER PREGUNTA RELACIONADA CON LA ELECTRICIDAD.
PIEZAS INCLUIDAS PARA EL ENSAMBLAJE Y LA INSTALACIÓN (dibujos de piezas no en escala): Piezas Cantidad Arandela de Plástico 2 Arandela de Metal 2 Tuerca exagonal G5/32” 2 Conector de alambre 3 Tuerca exagonal G3/8” 1 Outlet Box Screw 2 Tornillo Verde a Tierra 1 Niple de Montaje 1 Tornillo de Soporte 2 Tuerca de Tapa 2 Barra de Montaje 1 Pantalla de Cristal 1 Florón 1 Tapa 1 Cuerpo del Artefacto 1 11
ENSAMBLAJE E INSTALACIÓN: ALAMBRE BLANCO DE FUENTE DE ELECTRICIDAD ALAMBRE A TIERRA DE LA FUENTE DE ELECTRICIDAD ALAMBRE BLANCO TORNILLO DE SOPORTE BARRA DE MONTAJE TORNILLO CAJA DE EMBUTIR CAJA DE EMBUTIR ALAMBRE NEGRO DE FUENTE DE ELECTRICIDAD CONECTOR DE ALAMBRE ALAMBRE NEGRO TORNILLO VERDE A TIERRA G5/32” TUERCA EXAGONAL ALAMBRE DE COBRE DESNUDO A TIERRA DOSEL TUERCA DE TAPA BRAZO ENSAMBLAJE DE PORTALAMPARAS CASQUILLO NIPLE DE MONTAJE ARANDELA DE METAL ARANDELA DE PLASTICO PANTALLA DE CRISTAL ARANDELA
INSTRUCCIONES DE ENSAMBLAJE E INSTALACIÓN: 1. Desconecte el suministro eléctrico principal de su casa o edificio desde la caja de fusibles o disyuntor de circuito. 2. Apriete los tornillos de soporte (largos) dándole vueltas completas en el interior del orificio de montaje de la barra de montaje (el ajuste total se hará más tarde) y asegure con la tuerca exagonal de G5/32 pulgadas.
LOCALIZACIÓN Y CORRECCIÓN DE FALLOS: Causa Posible del Problema Luces no prenden. Acción para Corregir el Problema 1. La fuente de electricidad está apagada. 1. Asegúrese de prender la fuente de electricidad. 2. El “switch” o enchufe está malogrado. 2. Pruebe o reemplace el enchufe. 3. Falla en la conexión de los cables. 3. Revisar los cables. Se explota un fusible o el 1. Cables cruzados o la electricidad que llega 1. Revisar las conexiones de los cables.
DIRECTIVES D’ASSEMBLAGE ET D’INSTALLATION PLAFONNIER À 2-LUMIÈRES SEMI-ENCASTRÉ COLLECTION GRACE HOME DEPOT SKU# 515-193 (UPC# 802513146929) FINI LAITON ANTIQUE 15
Merci d’avoir acheté ce plafonnier semi-encastré de la compagnie Hampton Bay. Ce produit a été fabriqué en respectant les plus hautes normes de qualité et de sécurité. PARTICULARITÉS : 1. Facile à installer. 2. Plafonnier à deux lumières au fini laiton antique et abat-jour texture au motif de vagues. 3. Ce plafonnier économise l’énergie grâce à une conception qui permet l’utilisation en toute sécurité d’une ampoule fluocompacte à ballast électronique intégré au lieu d’une ampoule incandescente.
MISE EN GARDE : 1. Avant de procéder à l’installation de ce luminaire ou d’enlever l’ancien luminaire, débrancher l’alimentation électrique en fermant le disjoncteur de circuit ou en retirant le fusible de la boîte de fusibles. 2. POUR TOUTE QUESTION EN MATIÈRE D’ÉLECTRICITÉ, CONSULTER UN PROFESSIONNEL EN ÉLECTRICITÉ.
PIÈCES COMPRISES POUR L’ASSEMBLAGE ET L’INSTALLATION : (les pièces ne sont pas à échelle) Pièces Qté Rondelle de plastique 2 Rondelle de métal 2 Écrou hexagonal G5/32 po 2 Capuchon de connexion 3 Écrou hexagonal G3/8 po 1 Vis de boîte de sortie 2 Vis verte de mise à la terre 1 Tige filetée 1 Vis de support 2 Bouton 2 Plaque de fixation 1 Abat-jour en verre 1 Corps du luminaire 1 Capuchon 1 Faîteau 1 18
ASSEMBLAGE ET INSTALLATION : CABLE BLANC DE L'ALIMENTATION ELECTRIQUE CABLE DE MISE A LA TERRE DE L'ALIMENTATION ELECTRIQUE CABLE BLANC VIS DE SUPPORT PLAQUE DE FIXATION VIS DE LA BOITE DE SORTIE BOITE DE SORTIE CABLE NOIR DE L'ALIMENTATION ELECTRIQUE CAPUCHON DE CONNEXION CABLE NOIR VIS VERTE DE MISE A LA TERRE ECROU HEXAGONAL G5/32 PO CABLE DE CUIVRE DE MISE A LA TERRE COUVERCLE BOUTON BRAS ASSEMBLAGE DE DOUILLE TRAVERSEE TIGE FILETEE RONDELLE DE METAL RONDELLE DE PLASTIQUE ABAT-JOUR EN VERRE RONDELLE D
DIRECTIVES D’ASSEMBLAGE ET D’INSTALLATION : 1. Fermer l’alimentation électrique principale à partir de la boîte à fusibles ou du disjoncteur de circuit de votre domicile ou de votre édifice. 2. Effectuer des tours complets pour serrer les vis de support (longues) à l’intérieur du trou situé sur la plaque de fixation (à resserrer ultérieurement), fixer avec un écrou hexagonal G5/32 po. Les vis de support (longues) devraient dépasser su couvercle lorsqu’il est monté. (Ajuster au besoin) 3.
DÉPANNAGE : Causes possibles Les lumières ne s’allument pas. 1. L’alimentation électrique est fermée. 2. L’interrupteur est défectueux. 3. Branchement incorrect ou défectueux. Le fusible saute ou le 1. Croisement des connexions ou le câble de disjoncteur est déclencher mise à la terre n’est pas bien brancher. lorsque la lumière s’allume Action corrective 1. Vérifier que l’alimentation électrique soit en marche 2. Vérifier ou remplacer l’interrupteur. 3. Vérifier le câblage. 1.