PLATINUM Series CAN WIDEBAND CONTROLLER WBC 1 & WBC 2 (HT059970 & HT059980) QUICK START GUIDE HALTECH HEAD OFFICE: PH: +612 9729 0999 FAX: +612 9729 0900 EMAIL: sales@haltech.com HALTECH US OFFICE: PH: 760 598 1941 FAX: 760 598 1987 EMAIL: usa@haltech.com See the Haltech Website for your local authorized dealer. www.haltech.
LIMITED WARRANTY Lockin Pty Ltd trading as Haltech warrants the Haltech TM Programmable Fuel Injection System to be free from defects in material or workmanship for a period of 12 months from the date of purchase. Proof of purchase, in the form of a bill of sale or receipted invoice, which indicates that the product is within the warranty period, must be presented to obtain warranty service.
Haltech CAN Wideband Controllers (WBC 1 & WBC 2) Quick Start Guide Congratulations on purchasing a Haltech CAN Wideband Controller. This Plug and Play product allows the user the ability to increase the functionality of their Haltech ECU by using the Haltech CAN system which is fitted to all Platinum Series ECU's. The Haltech CAN Wideband Controller allows the user to accurately measure air/fuel ratios over a wide range from rich to lean via the Haltech CAN system for precise engine tuning.
Installation Installing the Haltech CAN Wideband Controller into a vehicle is simple.
Method 3: Connection Via Analogue output to Non Haltech CAN Supported ECU The Haltech CAN Wideband Controller is able to be used with ECU's that do not support the Haltech CAN System. To enable the Haltech CAN Wideband Controller to function as an analogue device please connect the harness as described below: • • • • • • • Figure 14 – Haltech WBC 2 Installation Diagram (CAN) Connect the Red wire labelled "+13.8V Battery" to a + Battery Fused source (7.
Harness Installation Wiring Diagrams Ensure the Haltech CAN Wideband Controller is NOT connected to the wiring harness until installation of the harness has been completed. The wires labeled “Main Power Input” supply power to the device. Connect the Red wire to Battery (+) terminal via an inline fuse (7.5A Minimum) Connect the Black wire to Battery (-) terminal or the chassis of the vehicle.
Harness Pinout Free Air Calibration After installation, a free air calibration is required, preferably with the O2 sensor removed from the exhaust and in free air. Calibration Procedure: Turn the free air calibration trimpots on the Haltech CAN Wideband Controller full counterclockwise. Turn ignition on and wait for 60 seconds so the system can fully stabilize. Slowly turn each free air calibration trimpot clockwise until the corresponding LED starts flashing at a rapid rate.
Optional Digital Display Gauge Installation Software Setup Installation of the optional Haltech digital display gauge will allow the user to see the Air / Fuel Ratio of the engine without the need for a laptop. With your new Haltech CAN Wideband Controller installed it's now time to setup the software.
Optional Digital Display Gauge Installation Software Setup Installation of the optional Haltech digital display gauge will allow the user to see the Air / Fuel Ratio of the engine without the need for a laptop. With your new Haltech CAN Wideband Controller installed it's now time to setup the software.
Harness Pinout Free Air Calibration After installation, a free air calibration is required, preferably with the O2 sensor removed from the exhaust and in free air. Calibration Procedure: Turn the free air calibration trimpots on the Haltech CAN Wideband Controller full counterclockwise. Turn ignition on and wait for 60 seconds so the system can fully stabilize. Slowly turn each free air calibration trimpot clockwise until the corresponding LED starts flashing at a rapid rate.
Harness Installation Wiring Diagrams Ensure the Haltech CAN Wideband Controller is NOT connected to the wiring harness until installation of the harness has been completed. The wires labeled “Main Power Input” supply power to the device. Connect the Red wire to Battery (+) terminal via an inline fuse (7.5A Minimum) Connect the Black wire to Battery (-) terminal or the chassis of the vehicle.
Method 3: Connection Via Analogue output to Non Haltech CAN Supported ECU The Haltech CAN Wideband Controller is able to be used with ECU's that do not support the Haltech CAN System. To enable the Haltech CAN Wideband Controller to function as an analogue device please connect the harness as described below: • • • • • • • Figure 14 – Haltech WBC 2 Installation Diagram (CAN) Connect the Red wire labelled "+13.8V Battery" to a + Battery Fused source (7.
Installation Installing the Haltech CAN Wideband Controller into a vehicle is simple.
Haltech CAN Wideband Controllers (WBC 1 & WBC 2) Quick Start Guide Congratulations on purchasing a Haltech CAN Wideband Controller. This Plug and Play product allows the user the ability to increase the functionality of their Haltech ECU by using the Haltech CAN system which is fitted to all Platinum Series ECU's. The Haltech CAN Wideband Controller allows the user to accurately measure air/fuel ratios over a wide range from rich to lean via the Haltech CAN system for precise engine tuning.
LIMITED WARRANTY Lockin Pty Ltd trading as Haltech warrants the Haltech TM Programmable Fuel Injection System to be free from defects in material or workmanship for a period of 12 months from the date of purchase. Proof of purchase, in the form of a bill of sale or receipted invoice, which indicates that the product is within the warranty period, must be presented to obtain warranty service.
PLATINUM Series CAN WIDEBAND CONTROLLER WBC 1 & WBC 2 (HT059970 & HT059980) QUICK START GUIDE HALTECH HEAD OFFICE: PH: +612 9729 0999 FAX: +612 9729 0900 EMAIL: sales@haltech.com HALTECH US OFFICE: PH: 760 598 1941 FAX: 760 598 1987 EMAIL: usa@haltech.com See the Haltech Website for your local authorized dealer. www.haltech.
