PLATINUM Sport 2000 Haltech 2JZ Terminated Engine Harness with HPI 6 (HT051462) QUICK START GUIDE HALTECH HEAD OFFICE: PH: +612 9729 0999 FAX: +612 9729 0900 EMAIL: sales@haltech.com HALTECH US OFFICE: EMAIL: usa@haltech.com See the Haltech Website for your local authorized dealer. www.haltech.
LIMITED WARRANTY Lockin Pty Ltd trading as Haltech warrants the Haltech TM Programmable Fuel Injection System to be free from defects in material or workmanship for a period of 12 months from the date of purchase. Proof of purchase, in the form of a bill of sale or receipted invoice, which indicates that the product is within the warranty period, must be presented to obtain warranty service.
Appendix PLATINUM Sport 2000 Haltech 2JZ Terminated Engine Harness with Haltech High Power Igniter Module Quick Start Guide Upon installation fill out the table below, this will help when it comes to setup and tuning of the vehicle Input / Output Wire Colour Harness Location Configuration Congratulations on purchasing a Haltech Engine Management Terminated Engine Harness. This Plug and Play product allows you to be up and running in a few hours.
Harness Overview The Haltech 2JZ Terminated Engine Harness is a plug and play solution for wiring a Toyota 2JZ-GTE Engine. Installation is simple and easy as the harness is designed for the engine, all lengths are correct and all wires are clearly labeled. Haltech HPI Ignition Harness Overview The Haltech 2JZ Terminated Engine Harness incorporates the use of a Haltech High Power Igniter unit for the ignition.
Trim Module Connector Harness Connections The Trim Module connector can be used in conjunction with the optional Haltech Trim Module ( #HT010502) to make quick manual adjustments to the Boost level / Fuel Injection Times and Ignition Timing depending on software setup. Only one option can be adjusted at any one time with the single Haltech Trim Module. Main Power Alternatively this connection uses Analogue Voltage Input 2 (AVI2) which can be used / wired as a standard function input if required.
• In Cabin Harness Spare DPO Connector The In Cabin harness comprises of the following wire connections The Spare DPO connector contains two Digital Pulsed Outputs (DPO 17 and DPO 18), and one +12V DC Switched Power. Digital Pulsed Outputs 1 & 2 ( V/B & V/BR ) When the output is activated by the ECU the output will switch to ground.
Ignition Output Connector • The Platinum Sport 2000 2JZ Terminated Loom and HPI 6 Kit is setup to be used with a Haltech HPI 6 Unit. The Supplied HPI Ignition harness will connect to this 8 position Deutsch connector. The ignition setup in the Platinum Sport ECU will be as follows: Spark Mode: Spark Edge: Dwell Mode: Dwell Time: This input can be programmed within the ECU Manager Software to read inputs such as: Direct Fire Falling Constant Charge 2.
Trim Module Connector Harness Connections The Trim Module connector can be used in conjunction with the optional Haltech Trim Module ( #HT010502) to make quick manual adjustments to the Boost level / Fuel Injection Times and Ignition Timing depending on software setup. Only one option can be adjusted at any one time with the single Haltech Trim Module. Main Power Alternatively this connection uses Analogue Voltage Input 2 (AVI2) which can be used / wired as a standard function input if required.
• In Cabin Harness Spare DPO Connector The In Cabin harness comprises of the following wire connections The Spare DPO connector contains two Digital Pulsed Outputs (DPO 17 and DPO 18), and one +12V DC Switched Power. Digital Pulsed Outputs 1 & 2 ( V/B & V/BR ) When the output is activated by the ECU the output will switch to ground.
Auxiliary Output Connector 02 Sensor Connector The Auxiliary Output connector contains two Digital Pulsed Outputs (DPO 3 & DPO 4), and two +12V DC Switched Power connections. The 02 Sensor connector comprises of the following connections: When the output is activated by the ECU the output will switch to ground. Solenoid valves and shift lights etc can be run directly from the output, however high current devices such as thermo fans and additional fuel pumps must be activated through a relay.
Auxiliary Output Connector 02 Sensor Connector The Auxiliary Output connector contains two Digital Pulsed Outputs (DPO 3 & DPO 4), and two +12V DC Switched Power connections. The 02 Sensor connector comprises of the following connections: When the output is activated by the ECU the output will switch to ground. Solenoid valves and shift lights etc can be run directly from the output, however high current devices such as thermo fans and additional fuel pumps must be activated through a relay.
Ignition Output Connector • The Platinum Sport 2000 2JZ Terminated Loom and HPI 6 Kit is setup to be used with a Haltech HPI 6 Unit. The Supplied HPI Ignition harness will connect to this 8 position Deutsch connector. The ignition setup in the Platinum Sport ECU will be as follows: Spark Mode: Spark Edge: Dwell Mode: Dwell Time: This input can be programmed within the ECU Manager Software to read inputs such as: Direct Fire Falling Constant Charge 2.
Harness Overview The Haltech 2JZ Terminated Engine Harness is a plug and play solution for wiring a Toyota 2JZ-GTE Engine. Installation is simple and easy as the harness is designed for the engine, all lengths are correct and all wires are clearly labeled. Haltech HPI Ignition Harness Overview The Haltech 2JZ Terminated Engine Harness incorporates the use of a Haltech High Power Igniter unit for the ignition.
Appendix PLATINUM Sport 2000 Haltech 2JZ Terminated Engine Harness with Haltech High Power Igniter Module Quick Start Guide Upon installation fill out the table below, this will help when it comes to setup and tuning of the vehicle Input / Output Wire Colour Harness Location Configuration Congratulations on purchasing a Haltech Engine Management Terminated Engine Harness. This Plug and Play product allows you to be up and running in a few hours.
LIMITED WARRANTY Lockin Pty Ltd trading as Haltech warrants the Haltech TM Programmable Fuel Injection System to be free from defects in material or workmanship for a period of 12 months from the date of purchase. Proof of purchase, in the form of a bill of sale or receipted invoice, which indicates that the product is within the warranty period, must be presented to obtain warranty service.
PLATINUM Sport 2000 Haltech 2JZ Terminated Engine Harness with HPI 6 (HT051462) QUICK START GUIDE HALTECH HEAD OFFICE: PH: +612 9729 0999 FAX: +612 9729 0900 EMAIL: sales@haltech.com HALTECH US OFFICE: EMAIL: usa@haltech.com See the Haltech Website for your local authorized dealer. www.haltech.
