Gas Fire Pit Table Assembly & Care instructions Model : 4527FTMB-23 Please read & retain for future reference
Keep the instructions for future reference Do not use this equipment if any part is flooded with water. Call technical service immediately to inspect the equipment and replace any part of the control system and any gas controller.
WARNING SAFETY RULES PLEASE READ THE FOLLOWING SAFETY RULES PRIOR TO OPERATION OF THE HEATER DANGER FIRE OR EXPLOSION HAZARD WARNING: For Outdoor Use Only. Installation and service must be performed by a qualified installer,service agency,or the gas supplier. 1) For use outdoors or in amply ventilated areas. 2) An amply ventilated area must have a minimum of 25 % of the surface area open. 3) The surface area is the sum of the walls surface. If you smell gas: Shut off gas to the appliance.
WARNING Read the instructions before installation and use.
TABLE OF CONTENTS Warning Safety Rules ....................................................3 Caution ..............................................................................6 Heater Stand and Location ...............................................8 Gas Requirements ......... .............................................8 Leakage Test ................................................................8 Operation And Storage ....................................................9 Cleaning and Care .........
CAUTION PLEASE READ CAREFULLY THE FOLLOWING SAFETY GUIDELINES BEFORE OPERATION. Do not use the fire pit indoors, as it may cause personal injury or property damage. This outdoor fire pit is not intended to be installed on recrea�onal vehicles and/or boats. Installa�on and repair should be done by a qualified service person. Improper installa�on adjustment, altera�on can cause personal injury or property damage. Do not a�empt to alter the unit in any manner.
Do Not use this appliance with an adjustable regulator. We suggest use this appliance with LPG cylinder of 5KG. The maximum diameter and the maximum height of the cylinder is 380mm and 450mm as shown in (Fig.1). Pay a�en�on when put the cylinder to the cylinder hole, ensure the hose connect to the cylinder not touch the hot surface. Keep the cylinder in place during opera�on. Never put spare cylinder in the same cylinder enclosure. Never block the way of shu�ng off the cylinder valve.
WALL The heater is primarily for outdoor use only. Always ensure that adequate fresh air ven�la�on is provided. Always maintain proper clearance to combus�ble materials, i.e. top 153 cm and sides 122 cm minimum. Heater must be placed on level firm ground. Never operate heater in an explosive atmosphere like in areas where gasoline or other flammable liquids or vapors are stored. CEILING 153 CM HEATER STAND AND LOCATION 122 CM GAS REQUIREMENTS Use propane, butane or their mixtures gas only.
OPERATION AND STORAGE Warning: User shall pour lava rocks fully to cover the whole burner before opera�on. TO TURN ON THE FIRE PIT 1. Turn the control knob to the “OFF”posi�on (Figure a). 2. Fully open LP cylinder valve. Note: For ini�al start or a�er any cylinder change, hold Control Knob IN for 10 seconds to purge air from gas lines before proceeding. 3. Push in gas control knob and turn counterclockwise to “IGNITER”(Figure b) to light the fire pit.
A. Constr uction and characteristics Transportable terrace/fire pit with tank housing Casing in steel with powder-coa�ng or stainless steel. Gas hose connec�ons with metal clamp B. Specifications Use propane,butane or their mixtures gas only. Max. wa�age:50000BTU/Hr(14.65KW) The hose and regulator assembly must conform to local standard codes. Regulator outlet pressure should meet the corresponding appliance category in B. Specifica�on. The appliance requires approved hose in 0.7m length.
CLEANING AND CARE Wipe off powder coated surfaces with soft, moist rag. Do not clean the heater with cleaners that are combustible or corrosive. Remove debris from the burner to keep it clean and safe for use. Cover the burner unit with the optional protective cover when the heater is not in use. PARTS AND SPECIFICATIONS 25.2 inch 27.6 inch 45.1 inch 30.
ASSEMBLY PARTS I A+J D K G H C E 12 B F
PARTS LIST Part Description Description Qty A Table Top 1PC B Right Side Panel 1PC C Left Side Panel 1PC D Rear Panel 1PC E Gas Cylinder Base 1PC F Front Panel 1PC G Fixed Rod 1PC H Connecting Rod 2PCS I Burner Lid 1PC J Burner 1PC K Stop Lever 1PC L Bolt 1/4*12 24PCS 13
PARTS LIST Part Description Description Qty M Bolt 1/4*35 2PCS N Knob 1/4*15 4PCS O Allen wrench 1PC P Knob M8*35 1PC Q Adjustable foot 4PCS R Glass Stones 6KGS S M6 Spacer 4PCS T M6 Large spacer 4PCS U Cover 1PC 14
Part Description Extra Description Qty L Bolt 1/4*12 2PCS M Bolt 1/4*35 1PC N Knob 1/4*15 1PC S M6 Spacer 1PC T M6 Large spacer 1PC WARNING:Failure to locate parts in accordance with these diagrams, or failure to use special parts provided with this equipment, may result in property damage or personal injury.
Step 1:Connect the gas cylinder base (E) to the front panel (F) with bolts (M). NOTE:Please fully tighten all bolts at this time. M E x1 M 1/4*35 x2 F x1 O x1 Step 2:Align the holes at both ends of the connecting rod (H) to the holes of the front panel(F) and the gas cylinder base(E) respectively,and then fix them with bolts(L). NOTE:Please fully tighten all bolts at this time.
Step 3:Attach right side panel(B) and left side panel(C) to table top(A) using bolts(N) . NOTE:Please do not fully tighten bolts until unit is fully assembled. Carefully and gently to prevent damage to the burner equipment. A+J x1 N B x1 C 1/4*15 x4 T x4 x1 Step 4:Align the holes around the burner (J) with the holes on the Left Side Panel(C). NOTE:Carefully and gently to prevent damage to the burner equipment.
Step 5: Attach burner(J) to Left Side Panel(C) using bolts(L). NOTE: Please align the holes well and determine the direction of the fire switch(J) controller,do not reverse the top and bottom.Please do not fully tighten bolts until unit is fully assembled. L 1/4*12 x4 Step 6: Attach fixed rod(G) to right side panel(B) and left side panel(C) using bolts(L). NOTE: Please do not fully tighten bolts until unit is fully assembled.
Step 7: After aligning the stop lever (K), screw on the bolt (L). NOTE: Please do not fully tighten bolts until unit is fully assembled. L 1/4*12 K x4 x1 Step 8: Attach rear panel(D) to right side panel(B) and left side panel (C) using bolts(L). NOTE: Please do fully tighten bolts until unit is fully assembled.
Step 9: Mount adjustable foot(Q) on the Leg. NOTE: Please fully tighten all bolts at this time. Q x4 Step 10: Insert the pressed door into the Right Side Panel(B) through the bolt.
Step 11: Check if the hook on the right panel is intact. Step 12: In the use process,the hook is used to store the Burner Lid(I).
Step 13: Please wear gloves to prevent the broken glass stone(R) from scratching your hands. Pour the glass stone (R) into the burner and place it evenly. R Step 14: Cover the lid and install the product.
Step 15: Put the installed windshield on the gas stove table.
Cover NOTE:We recommend the use of furniture covers to protect the patio fire pit when not in use; Please remove the wind guard before you use waterproof table cover. U x1 CLEANING AND MAINTENANCE Clean frame with mild soapy water,rinse thoroughly. Dry frame parts completely.Do not use bleach,acid, or other solvents on the fabric and metal parts. We recommend the use of furniture covers to protect the patio fire pit when not in use.
PROBLEMS CHECK LIST PROBLEM Burner will not light PROBABLE CAUSE SOLUTION Pressure is low Tank near empty Refill LPG tank Opening blocked Remove and clean Control not ON Turn valve to ON Thermocouple bad Replace thermocouple Pilot light assembly bent Place pilot properly Not in correct location Position properly and retry If the appliance is in case of any defaults or problems with assembly or use, please don't try to modify it by yourself. Contact with: E-mail:Service@alaulm.
DON'T WORRY ABOUT QUALITY- This propane Fire Pit table is made of new brown wicker made of high density polyethylene, with a thickened stainless steel frame, making it more fashionable, more durable and suitable for all weather. Provide sufficient warm and romantic campfire atmosphere for your family and friends. ETL APPROVED AND SAFETY- This gas fire pit table has passed the most dynamic safety certification in North America.