5021119 Gas Fire Pit Table Assembly & Care instructions Model:4327FTB Please read & retain for future reference
Keep the instructions for future reference Do not use this appliance if any part has been under water.
WARNING SAFETY RULES PLEASE READ THE FOLLOWING SAFETY RULES PRIOR TO OPERATION OF THE HEATER DANGER FIRE OR EXPLOSION HAZARD If you smell gas: Shut off gas to the appliance. Extinguish any open flame. If odor continues,leave the area immediately. After leaving the area,call your gas supplier or fire department. Failure to follow these instructions could result in fire or explosion,which could cause property damage,personal injury,or death.
FOR YOUR SAFETY 1.Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. 2.An LP cylinder not connected for use shall not be stored in the vicinity of this or any other appliance. WARNING Read the instructions before installation and use.
TABLE OF CONTENTS Warning Safety Rules....................................................4 Caution................................................................6 Heater Stand and Location...........................................7 Gas Requirements........................................................7 Leakage Test..................................................................7 Operation And Storage.................................................9 Cleaning and Care .................................
CAUTION PLEASE READ CAREFULLY THE FOLLOWING SAFETY GUIDELINES BEFORE OPERATION. Do not use the fire pit indoors, as it may cause personal injury or property damage. This outdoor fire pit is not intended to be installed on recreational vehicles and/or boats. Installation and repair should be done by a qualified service person. Improper installation adjustment, alteration can cause personal injury or property damage. Do not attempt to alter the unit in any manner.
Do Not use this appliance with an adjustable regulator. We suggest use this appliance with LPG cylinder of 5KG. The maximum diameter and the maximum height of the cylinder is 380mm and 450mm as shown in (Fig.1). Pay attention when put the cylinder to the cylinder hole, ensure the hose connect to the cylinder not touch the hot surface. Keep the cylinder in place during operation. Never put spare cylinder in the same cylinder enclosure. Never block the way of shuting off the cylinder valve.
WALL The heater is primarily for outdoor use only. Always ensure that adequate fresh air ventilation is provided. Always maintain proper clearance to combustible materials, i.e. top 153 cm and sides 122 cm minimum. Heater must be placed on level firm ground. Never operate heater in an explosive atmosphere like in areas where gasoline or other flammable liquids or vapors are stored. CEILING 153 CM HEATER STAND AND LOCATION 122 CM GAS REQUIREMENTS Use propane, butane or their mixtures gas only.
OPERATION AND STORAGE Warning: User shall pour lava rocks fully to cover the whole burner before operation. TO TURN ON THE FIRE PIT 1. Turn the control knob to the “OFF”position (Figure a). 2. Fully open LP cylinder valve. Note: For initial start or after any cylinder change, hold Control Knob IN for 10 seconds to purge air from gas lines before proceeding. 3. Push in gas control knob and turn counterclockwise to “IGNITER”(Figure b) to light the fire pit.
A. Construction and characteristics Transportable terrace/fire pit with tank housing Casing in steel with powder-coating or stainless steel. Gas hose connections with metal clamp B. Specifications Use propane,butane or their mixtures gas only. Max. wattage:50000BTU/Hr(14.65KW) Consumption: The hose and regulator assembly must conform to local standard codes. Regulator outlet pressure should meet the corresponding appliance category in B. Specification. The appliance requires approved hose in 0.7m length.
CLEANING AND CARE Wipe off powder coated surfaces with soft, moist rag. Do not clean heater with cleaners that are combustible or corrosive. Remove debris from the burner to keep it clean and safe for use. Cover the burner unit with the optional protective cover when the heater is not in use.
ASSEMBLY PARTS 12
Parts List Part Image Description Qty A Table Top 1 Pc B Right Side Panel 1 Pc C Left Side Panel 1 Pc D Rear Panel 1 Pc E Gas Cylinder Base 1 Pc F Door 1 Pc G Stiffener Panel 1 Pc H Bracket 2 Pcs I Caster 1 Pc J Burner 1 Pc K Burner Lid 1 Pc L Pull Ring 2 Pcs 13
Parts List Part Image Description Qty M Bolt M4x6 2 Pcs N Washer M1 2 Pcs O Bolt M6x15 16 Pcs P Bolt M6x35 4 Pcs Q Bolt M6x40 6 Pcs R Washer M6 22 Pcs S Allen Wrench 1 Pc T Knob 1 Pc U Glass Stones 6 KGS V Cover 1 Pc 14
Extra Part Image Description Qty M Bolt M4x6 1 Pc N Washer M1 1 Pc O Bolt M6x15 2 Pcs P Bolt M6x35 1 Pc Q Bolt M6x40 1 Pc R Washer M6 3 Pcs WARNING:Failure to position the parts in accordance with these diagrams or failure to use onlu parts specificaly apprived with this appliance may result in property damage or personal injury. You can scan the QR code to watch the install video.
Step 1:Attach gas cylinder base(E) to door (F) using bolts(Q) and washers(R). Install theknob(T) Note:Please do not fully tighten bolts until unit is fully assembled. Step 2:Attach brackets(H) to gas cylinder base(E) and door (F) using bolts(O) and washers(R). NOTE:Please fully tighten all bolts at this time. You can scan the QR code to watch the install video.
Step 3:Screw caster(I) to gas cylinder base(E). Step 4:Attach right side panel(B) and left side panel(C) to table top(A) using bolts(O) and washers(R). Note:Please do not fully tighten bolts until unit is fully assembled. You can scan the QR code to watch the install video.
Step 5:Attach rear panel(D) to right side panel(B) and left side panel(C) using bolts(O) and washers(R). Note:Please do not fully tighten bolts until unit is fully assembled. Step 6:Attach stiffener panel(G) to side panel(B) and left side panel(C) using bolts(P) and washers(R). NOTE:Please fully tighten all bolts at this time. You can scan the QR code to watch the install video.
Step 7:Attach burner(J) to table top(A) using bolts(O). NOTE:Please fully tighten all bolts at this time. Step 8:Insert Door and gas cylinder base(E&F) into the guide rail and push it to the end. NOTE:Please pour the glass stones(U) into the burner at this time and place them evenly. You can scan the QR code to watch the install video.
Step 9:Attach pull ring (L) to burner lid (K) using bolts (M) and washers (N). NOTE:We recommend the use of furniture covers to protect the patio fire pit when not in use; Please remove the wind guard before you use waterproof table cover. You can scan the QR code to watch the install video.
CLEANING AND MAINTENANCE Clean frame with mild soapy water,rinse thoroughly. Dry frame parts completely.Do not use bleach,acid, or other solvents on the fabric and metal parts. We recommend the use of furniture covers to protect the patio fire pit when not in use. Inspect and tighten all bolts on a regular basis to ensure proper performance and safety. In order to prolong the life and beauty of your patio fire pit table, we recommend storing it in a dry and protective area during off season periods.
PROBLEMS CHECK LIST PROBLEM Burner will not light PROBABLE CAUSE SOLUTION Pressure is low Tank near empty Refill LPG tank. Opening blocked Remove and clean Control not ON Turn valve to ON Thermocouple bad Replace thermocouple Pilot light assembly bent Place pilot properly Not in correct location Position properly and retry If the appliance is in case of any defaults or problems of assembly or use, please don't try to modify it by yourself. Contact with: E-mail:Service@alaulm.
DON'T WORRY ABOUT QUALITY- This propane Fire Pit table is made of new brown wicker made of high density polyethylene, with a thickened stainless steel frame, making it more fashionable, more durable and suitable for all weather. Provide sufficient warm and romantic campfire atmosphere for your family and friends. ETL APPROVED AND SAFETY- This gas fire pit table has passed the most dynamic safety certification in North America.
