Gas Fire Pit Table Assembly & Care instructions Model : 4527FTMB-23 Please read & retain for future reference
Keep the instructions for future reference Do not use this equipment if any part is flooded with water. Call technical service immediately to inspect the equipment and replace any part of the control system and any gas controller.
WARNING SAFETY RULES PLEASE READ THE FOLLOWING SAFETY RULES PRIOR TO OPERATION OF THE HEATER DANGER FIRE OR EXPLOSION HAZARD WARNING: For Outdoor Use Only. ,QVWDOODWLRQ DQG VHUYLFH PXVW EH SHUIRUPHG E\ D TXDOL¿HG LQVWDOOHU VHUYLFH DJHQF\ RU WKH JDV VXSSOLHU 1) For use outdoors or in amply ventilated areas. 2) An amply ventilated area must have a minimum of 25 % of the surface area open. 3) The surface area is the sum of the walls surface. If you smell gas: 6KXW Rႇ JDV WR WKH DSSOLDQFH ([WLQJXLVK DQ\ RSHQ
WARNING Read the instructions before installation and use.
TABLE OF CONTENTS Warning Safety Rules ....................................................4 Caution ..............................................................................6 Heater Stand and Location ...............................................8 Gas Requirements ......... .............................................8 Leakage Test ................................................................8 Operation And Storage .....................................................9 Cleaning and Care ........
11
CLEANING AND CARE :LSH RII SRZGHU FRDWHG VXUIDFHV ZLWK VRIW PRLVW UDJ 'R QRW FOHDQ the heater with cleaners that are combustible or corrosive. Remove debris from the burner to keep it clean and safe for use. Cover the burner unit with the optional protective cover when the heater is not in use. PARTS AND SPECIFICATIONS 25.2 inch 27.6 inch 45.1 inch 30.
ASSEMBLY PARTS I A+J D K G H C E 12 B F
PARTS LIST Part Description Description Qty A Table Top 1PC B Right Side Panel 1PC C Left Side Panel 1PC D Rear Panel 1PC E Gas Cylinder Base 1PC F Front Panel 1PC G Fixed Rod 1PC H Connecting Rod 2PCS I Burner Lid 1PC J Burner 1PC K Stop Lever 1PC L Bolt 1/4*12 24PCS 13
PARTS LIST Part Description Description Qty M Bolt 1/4*35 2PCS N Knob 1/4*15 4PCS O Allen wrench 1PC P Knob M8*35 1PC Q Adjustable foot 4PCS R Glass Stones 6KGS S M6 Spacer 4PCS T M6 Large spacer 4PCS U Cover 1PC 14
Part Description Extra Description Qty L Bolt 1/4*12 2PCS M Bolt 1/4*35 1PC N Knob 1/4*15 1PC S M6 Spacer 1PC T M6 Large spacer 1PC WARNING:Failure to locate parts in accordance with these diagrams, or failure to use special parts provided with this equipment, may result in property damage or personal injury.
Step 1:Connect the gas cylinder base (E) to the front panel (F) with bolts (M). NOTE:Please fully tighten all bolts at this time. M E [ M 1/4*35 F [ O [ [ Step 2:Align the holes at both ends of the connecting rod (H) to the holes of the front panel(F) and the gas cylinder base(E) UHVSHFWLYHO\ DQG WKHQ IL[ WKHP ZLWK EROWV / NOTE:Please fully tighten all bolts at this time.
Step 3:Attach right side panel(B) and left side panel(C) to table top(A) using bolts(N) . NOTE:Please do not fully tighten bolts until unit is fully assembled. Carefully and gently to prevent damage to the burner equipment. A+J [ N B [ C 1/4*15 [ T [ [ Step 4:Align the holes around the burner (J) with the holes on the Left Side Panel(C). NOTE:Carefully and gently to prevent damage to the burner equipment.
Step 5:Attach burner(J) to Left Side Panel(C) using bolts(L). NOTE:Please align the holes well and determine the direction of the ILUH VZLWFK - FRQWUROOHU GR QRW UHYHUVH WKH WRS DQG ERWWRP 3OHDVH do not fully tighten bolts until unit is fully assembled. L 1/4*12 [ Step 6:$WWDFK IL[HG URG * WR ULJKW VLGH SDQHO % DQG OHIW VLGH SDQHO & using bolts(L). NOTE:Please do not fully tighten bolts until unit is fully assembled.
Step 7: After aligning the stop lever (K), screw on the bolt (L). NOTE: Please do not fully tighten bolts until unit is fully assembled. L 1/4*12 K x4 x1 Step 8:Attach rear panel(D) to right side panel(B) and left side panel (C) using bolts(L). NOTE:Please do fully tighten bolts until unit is fully assembled.
Step 9:0RXQW DGMXVWDEOH IRRW 4 RQ WKH /HJ NOTE:Please fully tighten all bolts at this time. Q [ Step 10:Insert the pressed door into the Right Side Panel(B) through the bolt.
Step 11:Check if the hook on the right panel is intact. Step 12:,Q WKH XVH SURFHVV WKH KRRN LV XVHG WR VWRUH WKH %XUQHU Lid(I).
Step 13:Please wear gloves to prevent the broken glass stone(R) from scratching your hands. Pour the glass stone (R) into the burner and place it evenly. R Step 14:Cover the lid and install the product.
Step 15:Put the installed windshield on the gas stove table.
Cover NOTE:We recommend the use of furniture covers to protect the patio fire pit when not in use; Please remove the wind guard before you use waterproof table cover. U x1 CLEANING AND MAINTENANCE Clean frame with mild soapy water,rinse thoroughly. Dry frame parts completely.Do not use bleach,acid, or other solvents on the fabric and metal parts. We recommend the use of furniture covers to protect the patio fire pit when not in use.
PROBLEMS CHECK LIST PROBLEM Burner will not light PROBABLE CAUSE SOLUTION Pressure is low Tank near empty Refill LPG tank Opening blocked Remove and clean Control not ON Turn valve to ON Thermocouple bad Replace thermocouple Pilot light assembly bent Place pilot properly Not in correct location Position properly and retry If the appliance is in case of any defaults or problems with assembly or use, please don't try to modify it by yourself. Contact with: E-mail:Service@alaulm.
DON'T WORRY ABOUT QUALITY- This propane Fire Pit table is made of new brown wicker made of high density polyethylene, with a thickened stainless steel frame, making it more fashionable, more durable and suitable for all weather. Provide sufficient warm and romantic campfire atmosphere for your family and friends. ETL APPROVED AND SAFETY- This gas fire pit table has passed the most dynamic safety certification in North America.
