Instruction Manual
100X100X120MM
FIG-1-A1
FIG-1-A2
1
2
FIG-1-A3-a
FIG-A3-b
3
2
1
FIG-1-A4
2
1
FIG-1-A5
FIG-1-A6
FIG-1-B1
FIG-1-B3
FIG-2
1
2
OFF
ON
OFF
ON
Concrete installation.
Please install the side
marked with “up” label in
the top for backstand.
Note: In order to reach the required IP, the
input cable for the luminaries must be
H05RN-F 3×1.0mm², and threading
through before stripping.
Standard Recessed installation.
Please make sure the
thickness of the wood
board no less than 5mm
0.5-2.5mm² with
release facility
brown
blue
NL
N
L
green/yellow
N
o
t
e
:
P
l
e
a
s
e
k
e
e
p
t
h
e
c
a
b
l
e
o
u
t
l
e
t
i
n
t
h
e
s
a
m
e
v
e
r
t
i
c
a
l
d
i
r
e
c
t
i
o
n
w
i
t
h
t
h
e
i
n
l
e
t
t
o
l
u
m
i
n
a
r
i
e
s
EX183 B34
for cable/pipe mm: ∅5-10
H05RN-F 3×1.0mm²
for cable/pipe mm: ∅5-10
H05RN-F 3×1.0-1.5mm²
1
2
OFF
ON
3
4
NL
N
L
1
2
green/yellow
blue
brown
1
0.5-2.5mm² with
release facility
2
Attention:
when switching the colour
temperature, please make
sure the power is off.
4000K
3000K
Attention:
when switching the colour
temperature, please make
sure the power is off.
4000K
3000K
Boxing
1.Fix installation box to
inside of boxing.
2.Pour concrete,
when cured remove boxing.
3.Ensure protruding
nails are removed
before further installation.
Caution,risk of electric shock.
FIG-1-B2
3
2
1
H
o
l
e
d
i
m
e
n
s
i
o
n
Note: In order to reach the required
IP, the input cable for the luminaries
must be H05RN-F 3×1.0mm², and
threading through before stripping.
N
o
t
e
:
P
l
e
a
s
e
k
e
e
p
t
h
e
c
a
b
l
e
o
u
t
l
e
t
i
n
t
h
e
s
a
m
e
v
e
r
t
i
c
a
l
d
i
r
e
c
t
i
o
n
w
i
t
h
t
h
e
i
n
l
e
t
t
o
l
u
m
i
n
a
r
i
e
s
This luminaire must be installed by a qualified Registered Electrician to
prevent damage to the luminaire and maintain electrical safety.
If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the
manufacturer or his service agent or a similar qualified person in order to avoid a hazard.
The light source of this luminaire is not replaceable; when the light source reaches its end
of life the whole luminaire shall be replaced.
All exterior luminaires (with the exception of copper) require periodic cleaning to protect
the surface and/or coating from corrosion and ensure tidy appearance for the lifespan of
the product. Wash with care using a soft brush and warm soapy water using a neutral
detergent. Coastal areas require extra attention, especially fittings which are under
eaves/soffits and do not have any exposure to rain. Do not use a water blaster or high
pressure hose, do not submerge fittings for extended periods of time. 316 stainless steel
fittings will still develop surface rust or “tea staining” if left uncared for.
RISK OF FIRE - Required clearance from structural members and building elements
Side Clearance to building element (eg timber, joist or Batten) (SCB):
0mm
Height Clearance to building element (eg timber, joist or Batten) (HCB): 0
mm
Minimum Insulation Clearance to building element (MIC):
0mm
Recessed Luminaire Classification:
IC - building insulation that can safely be continuously
exposed to 90°C allowed to abut and cover the luminaire.
DO NOT INSTALL THROUGH JOIST, BEAM, RAFTER OR CEILING BATTEN
Note: Side/Height Clearance is measured from heat sink