User Guide

Remote Control
•
Tap test keys on LCD screen or any of hard keys
to test the selected code
•
Tap to search next code, or command will be
sent at the same time
•
Tap to skip previous code
•
Tap Back
Back
to cancel and return to previous menu
page for selection of other brand name. (Follow
the above steps again)
•
Tap OK
OK
to confirm and exit the setup
Note: If you have reached the end of code, you will be
prompted to continue for
A
A
u
u
to
to
-
-
S
S
e
e
a
a
r
r
ch
ch
or E
E
x
x
it
it
. For
details of Auto-Search setup, please refer to Auto-
Search Setup section in this manual.
E
E
n
n
t
t
e
e
r
r
C
C
ode
ode
– setup pre-programmed code by
entering code number. (Halcro Logic UTSR1 is
preloaded with numerous control codes for most
popular AV equipment; you can refer to the enclosed
code list for your devices.)
•
Tap E
E
n
n
t
t
e
e
r
r
C
C
ode
ode
from Setup menu
•
Select a device (e.g. TV)
•
Tap numeric digit to enter code number (check
your code from the code list, e.g. 0021)
•
Tap De
De
l
l
e
e
te
te
to delete the last entered digit (if you
have mistyped a number)
•
Tap Back
Back
to cancel and return to previous menu
page
•
Tap OK
OK
to confirm the input
•
Tap T
T
e
e
s
s
t
t
K
K
ey
ey
on LCD screen or any of hard key to
test the corresponding function
•
Tap O
O
K
K
to confirm and exit the setup
A
A
u
u
t
t
o
o
S
S
e
e
a
a
r
r
ch
ch
- setup pre-programmed code by
searching through the library.
•
Turn on your device before starting this setup
procedure (e.g. TV)
•
Tap A
A
u
u
to
to
S
S
e
e
a
a
r
r
ch
ch
from Setup menu
•
Select a device (e.g. TV)
•
Tap once and then repeat until your device is
switched off. Then, press OK
OK
to save the code. Or
you can tap the T
T
E
E
ST
ST
key to test the device during
setup
13
If you have missed the last code, tap once to
skip backward
•
Tap Back
Back
to cancel and return to previous menu
page
•
Tap OK
OK
to confirm and exit the setup
Note: When a code is set to a device, the learned
command and key name of that device will be lost,
and restored to pre-programmed command.
Some codes do not have Power command. These
codes may not be detected by using Auto-Search.
User is advised to use
T
T
e
e
st
st
key to test other keys.
During auto-searching, user can access any of the
hard keys to test the command.
A
A
d
d
v
v
anc
anc
ed
ed
Se
Se
t
t
-
-
U
U
p
p
E
E
d
d
i
i
t
t
This function allows you to rename, move or delete
key/device label.
Tap M
M
E
E
NU
NU
then tap E
E
D
D
IT
IT
and choose any one of
the following items:
K
K
e
e
y
y
N
N
a
a
me
me
- rename key label
•
Tap K
K
EY
EY
N
N
A
A
ME
ME
from Edit menu
•
Select a device
•
Select a key to be edited
•
Tap , , or for quick access to different
groups of keys (Character, Symbol or Graphic),
and tap or to access different pages of each
group of keys
•
Tap a character/symbol/graphic from the page
•
Tap D
D
E
E
L
L
E
E
TE
TE
to erase last entered
character/symbol/graphic
•
Tap B
B
A
A
CK
CK
to ignore and return to previous page
•
Tap OK
OK
to confirm and exit editing
Note: The number of characters input depends on the
corresponding key size
•
ABC ?!À
i