User Guide
Remote Control
B
B
ac
ac
k
k
li
li
g
g
h
h
t
t
There are two separate EL backlights for LCD screen
and hard keys, and will be turned ON separately.
Backlight will be turned ON for 5 seconds (factory
default setting) after a key is pressed, and user can
disable this function. (For details, please refer to
R
R
e
e
m
m
ot
ot
e
e
S
S
e
e
tt
tt
ing
ing
section in this manual.)
IR
IR
C
C
ode
ode
s
s
L
L
i
i
b
b
rar
rar
y
y
To setup a code, tap M
M
E
E
NU
NU
once then select a
device to setup, choose a setup method. User can
setup by learning key command from an original
remote control, entering a code number, browsing
through brand name list, or searching through the
whole library. Refer to separate Code List for IR code
number of different device.
C
C
o
o
n
n
f
f
i
i
g
g
ura
ura
t
t
i
i
o
o
n
n
/Se
/Se
tt
tt
i
i
n
n
g
g
U
U
p
p
t
t
h
h
e
e
U
U
n
n
i
i
t
t
Tap M
M
e
e
nu
nu
, then choose any one of the following
items:
S
S
e
e
t
t
u
u
p
p
–
–
setup the pre-programmed code or learn key
command.
•
Tap S
S
E
E
T
T
UP
UP
frommainmenu
•
Select one of following setup methods
L
L
e
e
a
a
r
r
n
n
i
i
ng
ng
– learn or copy a key command from an
original remote control to Halcro Logic UTSR1
•
Tap L
L
e
e
a
a
r
r
ning
ning
from Setup menu
•
Select a device where you would like to carry the
command keys (e.g. TV)
•
Tap a key to be learnt from the Halcro Logic UTSR1
•
im an original remote to the front of Halcro Logic
UTSR1. Press and hold the key until Halcro Logic
UTSR1 responds with a successful message
(approx. 5 seconds)
•
Edit the keyname or just tap OK
OK
to confirm
•
Tap another key to continue learning of the rest of
the useful commands
•
Tap M
M
E
E
NU
NU
to return to main menu, or tap
H
H
OME
OME
to return to main page
A
11
Dual
Dual
Signal
Signal
Learning
Learning
– If you find that a Learn
command only works occasionally for your audiovisual
equipment, your original remote control mayay contain
dual signals. Please follow the below steps to
reprogram these commands.
•
Tap L
L
e
e
a
a
r
r
ning
ning
from Setup menu
•
Select a device which you would like to carry the
command keys (e.g. TV)
•
Tap a key to be learnt from the Halcro Logic UTSR1
•
the original remote to the front of the Halcro
Logic UTSR1. Press and hold the key until Halcro
Logic UTSR1 responds with a successful message
(approx. 5 seconds)
•
Edit the key name or just tap OK
OK
to confirm
•
Tap the same key on the Halcro Logic UTSR1
Again aim the original remote to the front of the
Halcro Logic UTSR1. Press and hold the same key
until Halcro Logic UTSR1 responds with a
successful message
•
Edit the key name or just tap OK
OK
to confirm
Note: The optimum receiving distance is 5 to 8cm for
remote learning. If you have any reported problem
during the learning process, adjust the distance and
try again.
Brand
Brand
Name
Name
N
N
– setup pre-programmed code by
selecting a brand name.
•
Turn on your device you wish to install before start
this setup procedure. (e.g. TV)
•
Tap B
B
r
r
a
a
n
n
d
d
Na
Na
me
me
from Setup menu
•
Select a device (e.g. TV)
•
brand name list in alphabetical order will be
displayed. Tap or to browse the list, or tap a
character to access to a brand name. (e.g. ‘H’ for
Halcro)
•
Tap a brand name from the list, it will be highlighted
(e.g. Halcro)
Aim
•
A
5-8 cm