Instructions / Assembly

®
LED T8 Hybrid Lamps
ProLED T8 Hybrid Installation Instructions
© 2019 Halco Lighting Technologies, LLC. All rights reserved. Halco and ProLED are registered trademarks of Halco Lighting Technologies.
DANGER - RISK OF SHOCK-DISCONNECT POWER BEFORE INSTALLATION.
WARNING - RISK OF FIRE OR ELECTRIC SHOCK. LED RETROFIT KIT INSTALLATION REQUIRES
KNOWLEDGE OF LUMINAIRES ELECTRICAL SYSTEMS. IF NOT QUALIFIED, DO NOT ATTEMPT INSTALLATION
AND CONTACT A QUALIFIED ELECTRICIAN.
WARNING - RISK OF FIRE OR ELECTRIC SHOCK. PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH
THE NATIONAL ELECTRICAL CODE OR YOUR LOCAL ELECTR
ICAL CODE. IF YOU ARE NOT FAMILIAR WITH
THESE CODES AND REQUIREMENTS, CONTACT A QUALIFIED ELECTRICIAN.
WARNING - RISK OF FIRE OR ELECTRIC SHOCK. INSTALL THIS KIT ONLY IN LUMINAIRES THAT HAVE THE
CONSTRUCTION FEATURES AND DIMENSIONS SHOWN IN THE PHOTOGRAPHS AND/OR DRAWINGS AND
WHERE THE INPUT RATING OF THE RETROFIT KIT DOES NOT EXCEED THE INPUT RATING OF THE
LUMINAIRE.
WARNING - TO PREVENT WIRING DAMAGE
OR ABRASION, DO NOT EXPOSE WIRING TO EDGES OF SHEET
METAL OR OTHER SHARP OBJECTS. DO NOT MAKE OR ALTER ANY OPEN HOLES IN AN ENCLOSURE OF
WIRING OR ELECTRICAL COMPONENTS DURING KIT INSTALLATION.
DANGER - RISK OF SHOCK-DISCONNECT POWER BEFORE INSTALLATION. THE RETROFIT KITS INCLUDING
INSTALLATION INSTRUCTIONS, LED LAMP, LUMINAIRE MARKING LABELS. THE T8 LED TUBES ARE
INTENDED TO RETROFIT LISTED SURFACE MOUNTED, TYPE NON-IC OR TYPE IC RECESSED MOUNTED
FLUORESCENT LUMINAIRES WITH OR WITHOUT DIFFUSER FOR MAXIMUM FOUR LAMPS WITH LAMP TO
LAMP DISTANCE 11 CM MINIMUM; OR RETROFIT SURFACE MOUNTED LISTED FLUORESCENT LUMINAIRES
WITHOUT DIFFUSER FOR MAXIMUM SIX LAMPS WITH LAMP TO LAMP DISTANCE 5.5 CM MINIMUM.
WARNING - RISK OF FIRE OR ELECTRIC SHOCK. THE ELECTRICAL RATING OF THESE PRODUCTS ARE
120-277VAC, THE INSTALLER MUST DETERMINE WHETHER THEY HAVE 120-277V AT THE LUMINAIRE
BEFORE INSTALLATION.
INSTALLERS
SHOULD NOT DISCONNECT EXISTING WIRES FROM LAMPHOLDER TERMINALS TO MAKE
NEW CONNECTIONS AT LAMPHOLDER TERMINALS. INSTEAD INSTALLERS SHOULD CUT EXISTING
LAMPHOLDER LEADS AWAY FROM THE LAMPHOLDER AND MAKE NEW ELECTRICAL CONNECTIONS TO
LAMPHOLDER LEAD WIRES BY EMPLOYING APPLICABLE CONNECTORS.
THE RETROFIT KIT IS ACCEPTED AS A COMPONENT OF A LUMINAIRE WHERE THE SUITABILITY OF
THE COMBINATION SHALL BE DETERMINED BY AUTHORITIES HAVING JURISDICTION. PRODUCT
MUST BE INSTALLED BY A QUALIFIED ELECTRICIAN IN ACCORDANCE WITH THE APPLICABLE AND
APPROPRIATE ELECTRICAL CODES. THE INSTALLATION GUIDE DOES NOT SUPERSEDE LOCAL OR
NATIONAL REGULATIONS FOR ELECTRICAL INSTALLATIONS.
DO NOT USE WITH DIMMERS.
SUITABLE FOR DRY AND DAMP LOCATIONS.
THIS DEVICE IS NOT INTENDED FOR USE WITH EME
RG
ENCY EXITS.
FOR “ONE END” WIRING CONFIGURATION ONLY, WARNING: TO AVOID POTENTIAL FIRE OR SHOCK
HAZARD, DO NOT USE THIS RETROFIT KIT IN LUMINAIRES EMPLOYING SHUNTED BI-PIN LAMPHOLDERS.
NOTE: SHUNTED LAMP HOLDERS ARE FOUND ONLY IN FLUORESCENT LUMINAIRES WITH INSTANT-START
BALLASTS. INSTANT-START BALLASTS CAN BE IDENTIFIED BY THE WORDS "INSTANT START" OR "I.S."
MARKED ON THE BALLAST. THIS DESIGNATION
MAY BE IN THE FORM OF A STATEMENT PERTAINING TO
THE BALLAST ITSELF, OR MAY BE COMBINED WITH THE MARKING FOR THE LAMPS WITH WHICH THE
BALLAST IS INTENDED TO BE USED, FOR EXAMPLE F40T12/IS. FOR MORE INFORMATION, CONTACT THE
LED LUMINAIRE RETROFIT KIT MANUFACTURER.
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1)
THIS DEVICE MAY NOT CAUSE HARMF
UL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,
INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
Page: 1
General Safety Information
READ AND FOLLOW ALL SAFETY INSTRUCTIONS