Instruction Manual Hakomatic E 430 (7324.12) Instruction Manual Hakomatic E 430 (7324.
Introduction It is our desire that the excellent properties of the Hakomatic E 430 should justify the confidence you demonstrated by making this purchase. We did our best to supply you with an efficient and dependable machine. Before first operation of your Hakomatic read these instructions carefully. They will inform you in detail about operation of the item and contains valuable information fore service and maintenance.
Introduction Proper Use The Hakomatic E 430 vacuum scrubbing machine has been exclusively designed for floor cleaning, such as wet scrubbing. Whatever sort of use beyond the specified range will be deemed improper use; the manufacturer cannot be held liable for consequential damages. The term of proper use also includes compliance with the manufacturer's instructions about operation, maintenance and repair.
Table of contents 0 Introduction Proper use Notes of warrenty Acceptance of the machine 1 1 1 1 1 General safty instraction 3/5 2 Principle of operation 6 3 Description 7 3.1 Controls element 3.1.1 Switch for suction motor and brushes 3.2 Cleaning solution discharge 3.3 Pedal for lifting brush 3.4 Control for the speed of machine mouvment (Powerflow) 3.5 Raising/lowering the squeegee 3.6 Draining of soiled water tank 3.7 Draining of fresh water tank 4.3 Squeegee 4.3.
1. General safety instructions General information Apart from the information contained in this manual, the generally applicable legal provisions for safety and prevention of accidents must be adhered to. Do not put this manual aside without having read it, even if you did already operate similar ground cleaning equipment before. Allow yourself the time to do so in order to safe time at a later moment. The operator has to use the machine in accordance to its intended fields of application.
1. General safety instructions Caution! Never collect explosive fluids, undiluted acids and solvents! This includes e.g. gasoline, paint thinners or fuel oil, which - when penetrating the air being taken in - may form explosive vapours or mixtures; moreover acetone, undiluted acids and solvents if they should be aggressive to the material used for the machine components. Caution! This machine is not suitable for evacuation of dusts which are explosive or dangerous to health.
1. General safety instructions Handling of line cords Make sure that the line cords are not damaged by running over, squeezing, dragging , etc. The line cords shall be checked regularly with regard to damage and ageing. The machine must not be used unless the line cords are in proper condition. Use only original extension cables, the maximum admissible length being = 25 m. When using or replacing line cords, it is necessary to adhere to the type H05VVF3Gx1.5 specified by the manufacturer.
2. Principle of operation Hakomatic E 430 A squeegee and suitable brushes or pads are required for wet cleaning of hard floorings. The rotating brushes scrub the floor thoroughly, removing the dirt by means of suds, thus cleaning the floor. The soiled water is drawn in during the same cycle by means of the squeegee. This way the floor can be stepped on immediately afterwards, it is dry and clean. Useful advice for perfect work Prior to wet cleaning it is necessary to clean the floor.
3. Description 3.1 Control panel 3.1.1 Switch for suction motor and brush C A 4 1 High suction power When the floor is rough B shall be at this position B Fig.3 2 B Suction turbine speed selector Low suction power When the floor is smooth B shall be at this position 3 A on/off for suction turbine is on when “A” is at position “ “is off when “A” is at position “ “ Fig.2 1.Adjustable handle 2.Knob - handle 3.Lever for lifting the squeegee 4.
3. Beschreibung 3.2 Cleaning solution discharge D Switch for brush release 3.3 Pedal for lifting the brush Lever 2 1 D Fig.5 Fig.4 O brush will be released when D is at position “ “ and C is at position “ “ Control O Turn the lever up , to discharge the detergent and position the lever suitably to achieve the desired flow of Detergent. O Turn down to close the detergent flow. Important! Do not over-exert the lever; A gentle force is enough to close/open. Fig.
3. Description 3.4 Control for the speed of machine movement (Powerflow) O O O 3.5 Raising / lowering the squeegee Pull the black knob a little. Take the knob to the left to increase the speed. Take it to the right to decrease speed. Fig.7 O O To lower the squeegee move the lever knob to your left. To raise the squeegee move the lever knob to your right. 9 3. Beschreibung D Switch for brush release 3.2 Cleaning solution discharge 3.3 Pedal for lifting the brush Lever 2 1 D Fig.5 Fig.
3. Description 3.6 Draining of Soiled water tank O 3.7 Draining of Fresh water tank Is used to drain the soiled water. Note : when work is completed, the soiled water tank to be drained and rinsed O Is used to drain the fresh water. Note : The tank requires rinsing at regular intervals Please follow the below Procedure for draining tanks O O O O Slowly open the cap and allow drainage of the water. Re-close the cap. Re-attach the drain hose.
4. Taking into operation 4.1 Machine to the employment prepare When being supplied to you, the Hakomatic is packed in a cardboard box. The floor consists of a wooden plat form where the machine is fixed by means of plastic straps. Open the box from its bottom side and remove it by pulling upwards. 1 Tilt the body of the machine after removing rubber caps & allen screws(on both sides) in order to Gain access to the inside of the machine.
4. Taking into operation 3 Close the body back and secure it with screws and Rubber caps. Remove the two tie-bolts outside the body of the Machine . 4 Take the machine out of the pallette carefully. Fit the drain hoses (2 Nos.) ensuring the position of hooked end of the hoses. Take the power cord through the cable retainer.You now can take machine from the platform.
4. Taking into operation 4.2 Brushes and pads 4.2.2 Removal of brush The Hakomatic E 430 must be equipped with brushes from the accessories kit, as required by the degree of dirtiness and kind of ground. Refer to section "Technical Data" on page O O O O O O 4.2.1 Installation of brush O O O O O O O O O Power supply plugs pull Empty tanks. Dismount squeegee according to instructions on page 14/Fig. 12. Lower brush head. Tilt machine backwards and place on the brush lift-out pedal.
4. Taking into operation 4.3 Squeegee The Hakomatic E 430 is equipped with a squeegee with a working width of 750 mm . The squeegee bracket group fixed to the Hakomatic, allowing swiveling and the oscillating movements. The squeegee, protruding at the side, evades obstacles in the machines path and is made swivel backwards. Note: Before starting to work, check the squeegee for possibly collected foreign matter and for proper condition. 4.3.2 Removal of squeegee O O O Lift the squeegee.
4. Taking into operation 4.4 Wasser infeed O O Mount the new sealing strips by inverse sequence of operation. Tightening of the knurled nuts (just slightly, by hand) has to be done starting from the center towards outside (sealing strips with slots to frontside, and plain one to the rear) Note: If worn, the rear sealing strip can be turned at the frontside edge. Note: The supporting strip may Modify the sealing strip effect, hardsoft, and thus be adapted to different floor conditions.
4. Taking into operation 4.5 Operating procedure O O O O O Turn on switch "C" the brush is rotating . Turn the lever up , to discharge the detergent and position the lever suitably to achieve the desired flow of Detergent. Lower the brush head. Lower the squeegee. Turn on switch A the suction turbine is running. Note: After lowering the brush move the Hakomatic E 430 immediately; Otherwise the brush might leave traces on the floor. Lift the squeegee during reverse travel.
4. Taking into operation 4.5.1 Soiled and fresh water tanks 5 The Hakomatic E 430 has soiled water tank and a fresh water (lye) tank. The filling capacity is 22 litres; .Please do not fill beyond that mark; water temperature must not exceed 50C .Soiled water is fed via the suction hose into the soiled water tank. When work is finished: O O O O 4 Note: Do not collect any external Water.
4. Inbetriebnahme 4.6 Electrical equipment E The electrical equipment of the Hakomatic E 430 uses a mains voltage of 230V/50 Hz AC. Easy access to brush motor and suction turbine is possible after the upper part of the unit has been titled to upside. The suction turbine has been provided with a fuse (E ) having a rating of T6A. It must be replaced by a fuse of same rating (T stands for Time -lag).
5. Technical data Dimensions Length with squeegee Width without/with squeegee Height at handlebar, from ...to mm mm mm 930 450/750 807/870 Working width Brush head Squeegee mm mm 430 750 m2/h 1700 Driving speed Up to km/h 4 Weights Deadweight, dry Total weight, ready to operate, wet kg kg 76 98 Tyre Front wheel, dia./width Rear wheel, dia./width mm mm 75/28 150/30 Tank capacities Fresh water tank Soiled water tank l l 22 22 Surface performance, Theoretical 19 5.
5. Technical data Brush head Number of brushes Brush dia Brush speed Brush contact pressure, max.up to Specific ground pressure St mm 1/min kg N/cm2 1 430 280 22 0,25-0,35 Vacuum suction Air throughput Vacuum pressure m3/h mm/WS 155 2000 AC Volt EN 60335-2-72 EN 60335-2-72 W A A W W 230 I IPX3 1800 5 T6 800 1000 Electrical equipment Service voltage Protection class Protection kind Nominal power, total, max.
6. Brushes Brush Plastic PPN 0,5 7433 1 7087 7437 1 1 7436 1 7880 7881 1 1 7883 1 7. Pads Poly-Pad 41 cm braun Super -Pad brown (also necessary : drive plate 7436 ) Drive plate ( pad holder ) with center -lock 8. Additional tools for working with suction hose Flexible synthetic hose ,300 cm Suction tube , 130 cm , for connection onto hose 7880 Suction nozzle Bushea/Pads/ Additional tools for working with suction hose the degree of soiling and the kind of ground.
9. Maintenance and service 9.1 Maintenance work Compliance with our recommendations concerning maintenance work will give you the certitude always having a machine at your disposal, which is ready to work and in good operating condition. It is better to take precautions than to repair damages and less expensive! Please contact your local Hako distributor; the people there will be glad to perform that work for you. There well trained personnel and genuine Hako spare parts are at your disposal.
9. Maintenance and service 9.2 Maintenance table Betriebsstunden Daily every 50 every 100 every 200 Check the suction hose between squeegee and soiled water tank for tight fit. O O O Check the caps both of fresh and soiled water drain hose; check them for smooth Operation. O O O Check the squeegee sealing strips for wear; renew them if required. O O O Check the brush for tight fit and wear; renew them if required.
9. Maintenance and service 9.2 Maintenance table Betriebsstunden Daily every 50 Check the tank lid seal; renew it if required. Check the fresh water infeed to the brushes. O every100 every 200 O O O O Remove carbon dust from the suction motor ,Check the carbon brushes for easy Operation and wear, renew the carbon brushes as required. O Caution : Prior to any maintenance and repair work, remove the power Supply plug from the power supply.. Subsequently, perform a safety test as per VDE 7001.
Hakomatic B/E 430 Changes Due to Machine Directive 2006/42/EC Preface Modified text in paragraph Preface: Before using the equipment for the first time, read this original manual thoroughly, act according to the information contained and keep it in a safe place for future reference or subsequent owners.
EC Declaration of Conformity (corresponds to EC Directive 2006/42/EC) Hako GmbH Hamburger Straße 209-239 D-23843 Bad Oldesloe declares that the products Hakomatic B 430, Typ 7336.02 Hakomatic E 430, Typ 7324.12 to which this declaration relates, conform to the relevant provisions of the safety and health requirements stipulated in EC Directive 2006/42/EC and is in accordance with 2004/108/EC.
Superior technology for a cleaner and better environment (0 45 31) 806-0 · Fax (0 45 31) 806-338 Spitzentechnik für eine saubere und schönere Umwelt Superior technology for a cleaner and better environment Hako-Werke GmbH · Stammwerk und Hauptverwaltung · Headquarter (0 45 31) 806-0 · Fax (0 45 31) 806-338 Hamburger Str. 209-239 · D-23843 Bad Oldesloe · 88-60-2614/11-2010 • Printed in Germany Hako GmbH · Hamburger Str.
