Fully automatic washing machine This manual is for XQB60-68 Special number: 0030805945 Please read this manual carefully before using. Retain it for future reference.
Contents Names of the parts Safety precautions Installation and adjustment Installation the water inlet hose Preparation before washing Put in the laundries Put in the detergent Use the operation knobs Close the top lid Finish washing Disposal after washing Trouble shooting *Answers to question Packing list Specification Water level/Water quantity (about) High/52L, Medium/43L, Low/30L Injection pressure(MPa Rated washing / spinning capacity(kg) 6.0/6.
Names of the parts Top lid Detergent box Lint filter(Installed by user) Water level knob Water inlet valve Power switch Power wire Cabinet handle Control panel seat Water channel Filter cover Inner tub Front control board Control panel sheet Pulsator Cabinet Drain hose Drain hose hanging hole Drain outlet protecting cover Drain hose bushing Back cover Adjustable foot Adjustable foot seam Rear fixed foot Meaning and description of the symbols Warning sign Forbidding sign Contents marked with that
Safety precautions Please insert the power cord into special receptacle with rated voltage.Be sure to use single-phase three pins receptacle.The earthing terminal of the receptacle must be earthed reliably.If possible,please adopt electric leakage protector. When the machine is normally using, please put the power plug at the location easily to be inserted and extracted by hand. Be sure to pull the plug off when there's power failure, or the machine is being moved, cleaned orwhen it is idle.
Safety precautions Do not stretch hands into the working machine. It is dangerous even if the rotation is slow. Take special care of the children. Do not put any hot or heavy items (such as the kettle with hot water ) on the washing machine. Do not decompose, repair or alter the machine by yourself. Do not wash laundries with volatile materials (such as thinner, petrol etc.) l Petro The handicapped or children without care shall not use the machine.
Installation and adjustment Please install and adjust the machine according to the requirement of the manual. It is very important to your security and correct operating the machine. Install the bottom plate After you open the package, please lean the washing machine gently down on soft items ( like the towel cloth, blanket, etc. ). Install the bottom plate to the bottom of the machine with the eight screws by a cross screwdriver, then lift the machine up gently.
How to change the direction of the drain hose 1.Dismantle the back cover of the washing machine. 2.Put down the drain hose. Take off the drainhose frame. As indicated in Figure 1, put thedrain hose into the cabinet. Then stretch onehand into the cabinet to nip the claw of the drain hose bushing to remove the claw fromoriginal position. Take off the drain hose bushing with the other hand. (As indicated in Figure 2 and 3). 3.
Install the water inlet hose Confirm the water faucet Water faucet, not suitable Water faucet, suitable It is required that the front end shall be longer than 10cm. The outlet end surface of the faucet shall be flat and smooth. If not please file it to avoid leakage. Connection between the water inlet hose jointer and the water faucet 1.Press the lower end of the lock lever and push down the slider. Take off the water inlet hose jointer from the water inlet hose component. See to Figure 1. 2.
Connection between the water inlet hose and the washing machine 1.Do not take off the water absorption cushion. Please check if the cushion is dropped or damaged before each usage. If it happens please contact our after-sale department immediately. 2.Put the nut of the water inlet hose on the valve jointer. 3.Fasten the nut. Swing it gently to confirm if it's suitable.
1Preparation before washing Preparation before washing 1.Connect the water inlet hose. Open the water faucet. 2.Confirm that the washing machine is earthed reliably. Then insert the power plug into the receptacle. The earth terminal shall not link to gas pipeline and faucet water pipeline. 3.Put down the drain hose. Pay attention to followings before washing the laundries Check if the laundries has special requirement on washing Clear the Tie the long pocket.
2 Put in the laundries The capacity of washing and spinning of the machine refer to the largest weight of the standard laundries under dry condition that can be washed or spinned in one time. One time washing quantity shall be lower than the rated capacity. The thickness, size, type of the cloth will influence the actual washing capacity. It is suitable for one time washing to put in reasonable amount of laundries and the laundries can be turned round in washing.
4 Use the operation knobsand buttons a Description of the function of the knobs and buttons Mode and meaning of the indicators Flashing: indicate the running program On: indicate the program about to run, or indicate the selected mode Flashing rapidly: indicate abnormal condition Start Pause Process Selection Quickwash Spin Twice- Wash Rinse wash "Process selection" button One or more out of the five process programs are available for your option: quick- wash, twicewash,wash, rinse, spin "Start/Pause"
b .Steps of using the operation buttons and description of the steps "Power" botton Push the "Power" button to switch on or off the power. When the power is on, push it again to switch off the power. Process Selection Start Pause QuickTwice- Wash Rinse wash wash Spin Power Water Level Low Auto off Medium High Reset On Off Power Low Auto off Medium High Reset On Off "Water Level " button Select or adjust the water level.
Attention Even there's no water in the tub, the spinning will start after a certain period. Do not use the "Twice wash" program for the woolen laundries. Wash the laundries that are prone to lose colors separately from other laundries. The pulsator will not rotate unless the water is filled to selected water level.
* Total time: including the normal water inlet time, drain time, excluding the power off time. The total washing time may be influenced by the water inlet pressure and water level. * Spin time: the time from intermittent running to finishing * When selecting " Twice-wash " program, first soak for about 20 minutes, pre-wash for about 8 minutes, then soak for about 5 minutes, then do washing, rinsing and spinning. The wash time in the list includes the pre-wash time. 3.
Disposal after washing After using, please clean the lint and foreign materials of the lint filter etc. in time. Otherwise it may influence your using the machine. Please first pull off the power plug from the receptacle before cleaning. Clean the detergent box and set it on the control panel seat. The lint filter must be used during washing. It must be cleaned in time after each using Lint filter: 1.Pull it up to dismantle. 2.Push it down to install. 3.Clean the filter screen after washing.
Trouble-shooting Answers to question (If there's breakdown, please pull off the power plug before checking) The following phenomena are not breakdowns sometimes. Please confirm again before sending it to repair. If there are real breakdowns, please come to the special maintenance department or after-sale service department of our company. Do not repair it by yourself. Phenomenan The reason In spinning, the machine stops running.
Paching list Name Quantity User's manual One piece Components of the water inlet hose The end connecting to the washing machine Jointer connecting the water inlet hose and the water faucet One piece The end connecting to the water inlet hose jointer Bottom plate One piece Tapping screws Eight pieces Lint filter One piece Fully automatic washing machine One set
WASHING POWDER BOX 0030505636
