User's manual WM6002A Computerized Full-auto Washing Machine TWO DRIVE TWO 50% CONSUMPTION SAVER CONTENTS Before using Names of the parts.............the 2nd cover Safety precautions .............................................1 Installation and adjustment .........................3 Install the water inlet hose............5 Using process Preparation before washing ...............7 Put in the laundries .............................8 Put in the detergent ............................
Before Using Names of the parts Top lid component Inner cover component Detergent box Control pannel Outer tub cover water inlet valve rear faceplate front control board water absorption round cover cushion power cord Lint filter fixing Balance ring Inner tub Lint filter Filter cover Pulsator Attachment block (3 pieces) Cabinet Liquid whitener inlet cabinet handle drain hose hanging hole drain hose standby screws and nut for earthing wire Fixed leg (3 pieces) Adjustable leg Adjustable leg film back
Safety precautions Please plug the plug on special 220-240V AC receptacle. Be sure to use three phase power receptacle.Ensure the earthing prong of the power receptacle is earthed reliably.Use leakage protector if possible. Before Using In normal usage of the washing machine, the power plug shall be ready to be pulled or plugged with hand.
Safety precautions Do not put hand into the rotating tub.It is dangerous even if the rotation speed is slow. Take special care of the children. Keep children away from the washing machine to avoid them climbing on. Do not put any hot or heavy items (such as the kettle with hot water) on the washing machine. Before Using Do not decompose, repair or alter the machine by yourself. Do not wash laundry with volatile materials (such as thinner, petrol etc.).
Installation and adjustment Before Using Please install and adjust the machine according to the requirement of the mannual. It is very important to your security and correct operating the machine. Install the inner cover and lint filter 1.Open the top lid of the washing machine. 2.Put the inner cover component on the outer tub cover, aiming the inner cover shaft to the installation hole of the corresponding outer tub cover shaft groove. 3.
How to change the direction of the drain hose 1. Dismount the back cover of the washing machine. 2. Put down the drain hose. Take off the drain hose frame. As indicated in Figure 1, put the drain hose into the cabinet. Then put one hand into the cabinet to nip the claw of the drain hose bushing to release the claw from original position. Take off the drain hose bushing with the other hand. (As indicated in Figure 2 and 3). drain hose Before Using 3.
Before Using Install the water inlet hose Confirm the water faucet water faucet, suitable water faucet, not suitable The exit end face of the faucet It is required that the front end shall be longer than 10mm. The exit end face of the faucet shall be flat and smooth. If not please file it to avoid leakage. Connection between the water inlet hose jointer and the water faucet Use the new water inlet hose provided with the machine to connect to the water faucet.Old hose sets should not be reused. 1.
Before Using Connection between the water inlet hose and the washer 1.Do not take off the water absorption cushion. Please check if the cushion is dropped or damaged before each usage. If it happens please contact our after-sale department immediately. nut of the water inlet hose 2 Put the nut of the water inlet hose on the valve jointer. 3 Fasten the nut. Swing it gently to confirm if it's suitable. jointer of the water inlet valve water absorption cushion.
1 Preparation before washing Using process Preparation before washing 1.Connect the water inlet hose. 2.Confirm that the washing machine is earthed reliably . Then insert the power plug into the receptacle. Do not connect the earth terminal to the gas pipe and tap water pipe. 3.Put down the drain hose. Pay attention to followings before washing the laundries Confirm if there's Clear the pocket.
Using process 2 Put in the laundries The capacity of washing of the machine refer to the largest weight of the standard laundries under dry condition that can be washed in one time. Laundries quantity in one washing cycle shall be lower than the rated capacity. The largest capacity of this machine is 6.0kg. The thickness ,size , type of the cloth will influence the actual washing capacity.
Using process 3 Put in the detergent Put the washing powder and softener into the detergent box directly as indicated in the left figure. After that, please close the detergent box.Refer to the following list for the usage of the detergent : standard dosage of the detergent and the water quantity. Access for detergent and washing powder Access for softerner Detergent box How to use the whitener Fill water to decided level .Dilute the whitener with container. Pour it slowly into the washing tub.
Using process 4 Use the operation buttons Description of the function of buttons Digital tube Mode and meaning of the indicators During sensing, it displays During operation of programs, it displays the remained time (minute) or remained times of the corresponding procedure Flashing: indicate the running program On: indicate the program about to run, or indicate the selected mode Minut es Minute s Times Wa ter -sa vin g Minutes SOAK WASH RINSE “•• •• ” button Push the soak button to set the soak pr
“CHILD LOCK” function Push and hold the water level button and spin button, then push down the power on/off button. The digitron displays CL . You can continue setting desired washing procedures. After setting, push down the start/pause button. The child lock function is activated. All of the buttons are locked and cannot make selection. Release the child lock function: push down the water level and spin button at the same time for more than 1 second. After a beepsound, the child lock function is released.
Using process Steps of using the operation buttons and description of the steps WM6002A M in utes M in u te s Tim es Wa ter -sa vin g Minutes SOAK 9 7 5 3 1 10 Time remained (minutes) 8 Reserve 6 er) (hours lat 4 2 WASH RINSE SPIN + CHILD LOCK E FIBR ON COTT EN LL O W O SILK WATER LEVEL MAL NOR K QUIC ASTE TH POS N JEA POWER ON/OFF START PAUSE PROGRAM RESERVE Push the "POWER ON/OFF " button to switch on the power.
Using process After switching on the power, the washing machine will set to common program including"wash, rinse, spin "automatically. To select other procedures, push the "SOAK", " WASH", " RINSE" or "SPIN" button to select the time of soak, wash and spin, and the times of rinse. After switching on the power, if you push one of the button among "WASH", "RINSE"and"SPIN", the digitron of the former procedures will turn off automatically. The former procedures will not run.
Using process * Total time: including the normal water inlet time and drain time. The total washing time may be influenced by the water inlet pressure and water level.
Disposal after washing Using process After using, please clean the lint and foreign materials of the lint filter etc. in time. Otherwise it may influence your using the machine. Please first pull off the power plug from the receptacle before cleaning. Clean the detergent box and set it on the control panel seat. The lint filter must be used during washing. 1.The method of dismantle : Push it up aslant and gently. It must be cleaned in time after each using 2.
Trouble-shooting Answer to question (If there's breakdown, please pull off the power plug before checking) The following phenomena are not breakdowns sometimes. Please confirm again before sending it to repair. If there are real breakdowns, please come to the special maintenance department or after-sale service department of our company. Do not repair it by yourself. Phenomenan The reason The top lid is opened during reserve procedure. The digitron displays E0. How to settle Close the top lid.
Packing list Name Quantity Storage position User's manual One Inside the document bag Lint filter One Inside the document bag Components of the water inlet hose One Inside the accessory bag Bottom plate One Between the upper cushion of the washing machine package and the upper seal of the package carton Tapping screws ST4x16-A Eight Inside the accessory bag One Inside the accessory bag Inner cover component Computerized Automatic washing machine One
Specification Model Rated voltage WM6002A frequency Rated washing / spinning capacity 220-240V~ 50Hz 6.0kg (weight of standard dry cloth) Water level/Water quantity (about) 1/16L 2/20L 3/24L 4/28L 5/32L 6/38L 7/42L 8/45L 9/47L 10/50L Max water consumption About 75L(High water level; Standard program) Injection pressure 0.03MPa~0.
