TFT-LCD COLOUR TV Owner s Manual TFT-LCD TV High Brightness & Contrast Please read this manual carefully before using your television and keep this manual in a good place for future reference.
Contents English-1 Warning Front control panel Back cover interface Loading battery Functions of remote controller Operation instructions Screen display Programme setup Sound system & Video system set up Picture control Picture Control P.MODE Sound Control Set the Equalizer User 2 4 5 6 7 8 10 11 13 14 15 Sound Control S.
WARNING WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. DANGEROUS VOLTAGE Uninsulated Dangerous Voltage, that may be of sufficient magnitude to constitute a risk of electric shock, is present within the cabinet of this unit. ATTENTION The Owner's Manual contains important operating and maintenance instructions.
WARNING Power source connection 1 Plug the 12V AC-DC converter to the 12V input jack of the television set. 2 Correctly connect the AC wire to the AC-DC converter. 3 Insert the AC wire plug in the jack of AC power source. Disconnect the television set with the power source or antenna plug when it heavily rains with thunderstorm or power supply is interrupted. Do not tie electric cables to any other objects to avoid accident damages.
FRONT CONTROL PANEL 1 2 3 5 4 7 6 8 9 7 6 5 1 2 3 4 6 1 3 57 6 MENU 2 4 7 PR VOL 3 2 TV/AV 4 Note: The silk-screen or the array may be change without notice. 1 2 MENU V- V+ 3 P- P+ (programme number down/ up button) 4 5 6 7 8 9 Display the menu. ( volume down /up button) Adjust the volume or change the menu set. Select a channel or select an option in the menu. TV/AV To exchange between TV and other available video inputs Power Turns the TV set on/off.
BACK COVER INTERFACE 9 8 DC IN D-SUB IN 7 6 HEADPHONE PC AUDIO IN 5 SCART 4 S-VIDEO 3 AUDIO 2 VIDEO 1 ANT 1 Antenna input 2 External video input 3 External audio input 4 S terminal input 5 SCART input 6 Computer audio input 7 Headphone output slot 8 Computer/digital TV signal input 9 12V power input English-5
LOADING BATTERY Loading a battery to the compartment 1 Remove the cover of battery compartment as shown in the figure. 2 Properly load one 3V Li-Battery in the compartment of the remote controller. 3 Replace the cover of the battery compartment. Cautions 1 Ensure that there is no obstacle to signals from the remote controller to the receiving sensor of the television set. 2 Keep the remote controller away from heat source or high moisture and avoid impacts to the remote controller.
FUNCTIONS OF REMOTE CONTROLLER DC standby DISPLAY To display the SLEEP TIME,press the VOL+/- buttons to set the sleep time A2 stereo/NICAM selection Press to conceal the sound of programme DISPLAY To make sure the selection Adjusts volume, reset menu or enter submenu To call the main menu 1 2 3 SLEEP 4 5 6 NICAM 7 8 9 DIGITAL BASS AD 0 TV/AV OK CH+ Q.VIEW PC MENU VOL+ DVD CH- S.
OPERATION INSTRUCTIONS Turning the TV On and Off Standby Setup: The AC-DC converter and the AC power cord must be set up and connected to have the TV in standby mode ready to be turned on. Press the power button on the front panel of the TV to go into standby mode. POWER 1 If the TV is in standby mode, press the Power button on the remote controller to turn on the TV Set. 2 Press the Power button and the TV goes into standby mode.
OPERATION INSTRUCTIONS Mute function MUTE 1 Press the MUTE button then the sound will be switched off and the display appears. 2 You can cancel it by pressing the MUTE again. On screen language selection OSD TONE LANGUAGE SOUND SYSTEM COLOR SYSTEM SLEEP TIME OFF English DK Auto 0 min/0 min The menu can be displayed on the screen in desired language. First select your language. 1 Press the MENU button. 2 Select the third menu.
SCREEN DISPLAY How to select the item you want to adjust. 1 Press the MENU button and the main menu will appear on the screen. PICTURE MENU BRIGHTNESS 65 CONTRAST 65 SHARPNESS 65 COLOR 65 2 Press VOL+/- buttons to select PICTURE, SOUND,OPTIONS or TUNER Menu. 3 Press CH- button to enter the Menu then press CH-/+ buttons to select the item. 4 Press VOL+/- buttons to adjust Menu items or enter a submenu. SOUND MENU DIGITAL BASS OFF AVC OFF BALANCE 5 Press MENU or OK button to exit.
PROGRAMME SETUP Setting up TV programme CH- CH+ 1 2 3 4 5 6 7 8 9 Up to 200 TV programmes can be stored in this set. Once you have preset the programmes, you will be able to use the CH-/+ or NUMBER button to select the programmes . Programmes can be tuned using automatic or manual modes. 0 Auto programme(ATM) All programmes that can be received are stored by this method. It is recommended that you use auto programme during installation of this set. 1 Press the MENU button.
PROGRAMME SETUP Manual programme Manual programme lets you manually tune and arrange the programmes in whatever order you desire. 1 Press the MENU button. 2 Press VOL+ button to select the fourth menu. 3 Press PRO- button to enter the menu then press CH -/+ buttons to select the MANUAL STORE. 4 Press VOL+ button to start the search. Channel fine tuning Channel fine tuning is not suggested unless it is necessary when abnormal status occurs to achieve a better picture or sound quality.
PROGRAMME SETUP Skipping a programme ATM 1 Select a channel to be skipped with the CH-/+ or Number button. MANUAL STORE FINE TUNE ADD/ERASE CURRENT CHANNEL OFF 2 2 Press the MENU button. 3 Press VOL+ button to select the fourth menu. 4 Press CH- button to enter the menu then press CH -/+ buttons to select the ADD/ERASE. 5 Press VOL-/+ buttons to turn on/off the skip channel.
PICTURE CONTROL You can adjust Brightness, Contrast, Sharpness, Colour to the levels you prefer. 1 Press the MENU button. 2 Press VOL+ button to select the first menu. 3 Press CH- button to enter the menu then press CH-/+ buttons to select a picture item. 4 Press VOL-/+ buttons to adjust the picture parameter on as you want.
PICTURE CONTROL P.MODE (PICTURE STATUS Mode) 1 Press the P.MODE button. 2 Press the P.MODE button repeatedly to select . P.MODE 3 Each press of the button,the screen display changes as below. STANDARD: Standard Picture Appearance DYNAMIC:High picture contrast MOVIE: For moving picture MILD: Softer Picture Appearance CUSTOM:User mode Sound Control 1 Press the MENU button. DIGITAL BASS OFF AVC OFF BALANCE 2 Select the second menu.
SET THE EQUALIZER USER 1 Select Equalizer by pressing the CH- button and press VOL+ button to enter the submenu. DIGITAL BASS OFF AVC OFF BALANCE 65 EQUAUZER 2 Select a sound band by pressing the CH- button. 3 Make appropriate sound level with the VOL+ button. 4 Press the MENU button to exit. 120Hz 500Hz 1.5kHz 5kHz 10kHz 65 65 65 65 65 Sound Control S.MODE (Sound Status Mode) 1 You can press the S.MODE button repeatedly to select. Also you can define the CUSTOM mode by set the Equalizer.
OTHERS Option Control 1 Press the MENU button. 2 Press VOL+ button to select the third menu. 3 Press CH- button to enter the menu then press CH-/+ buttons to select the desired item. OSD TONE OSD TONE LANGUAGE SOUND SYSTEM COLOR SYSTEM SLEEP TIME OFF English DK Auto 0 min/0 min 1 When the OSD TONE is set ON, the background of the menu will be transparent.
EXTERNAL AUDIO AND VIDEO DEVICE CONNECTIONS Some external signal sources, such as VCR, video camera or PC, can be linked to the television.
CONNECTED TO PC AS A MONITOR SCART input You may get the Y Pb/Cb Pr/Cr signal of DVD from the SCART terminal by the SCART-DVD connecting cable. DVD Player with Y Pb/Cb Pr/Cr output terminal VGA input DC IN D-SUB IN HEADPHONE PC AUDIO IN SCART S-VIDEO AUDIO VIDEO ANT To PC AUDIO IN To D-SUB IN 1 Connect PC VGA output port with television D-SUB IN port. 2 Connect PC audio cable to television PC Audio IN port. 3 Press PC button for PC mode option.
SPECIFICATIONS Specifications of the television that you have just purchased may vary from the information in this table due to technical innovations. Model Dimensions L20AV6-A0 550X165X449 Net weight Power source Input 9.3kg --- 12V 5.0A 60W 60W L20L6A 552X210X440 8.9kg --- 12V 5.0A L15SV6-A0 419X170X353 5.4kg --- 12V 4.0A 48W L17LV6-A1 490X170X355 5.65kg --- 12V 5.0A 60W L17L6A-G1 445X210X395 6.5kg --- 12V 5.
TROUBLESHOOTING Verify and try to solve the problems by yourself according to the instructions specified in the table below before contacting the after-sales service for technical assistance. Do not set the television with a still picture for an extended period as this might result in image residue on the screen. Normal picture images will be resumed within 12 hours after normal programmes are displayed.
