User's Manual HWM70-A Fuzzy Computeried Automatic Washing Machine Contents Before using nd Names of the parts The 2 cover 1 Safety precautions 3 Installation and adjustment Install the water inlet hose 5 Using process Please read this manual carefully before using. Retain it for future reference Please check if the power receptacle has good earthing condition before using to guarantee your safety. The manufacturer will not bear the responsibility for those risks occurred from not obeying this manual.
Before using Names of the part s Top lid A Cool water valve Warm water valve Top lid B Detergent box Drier outlet cover Back faceplate Control panel Power line Cabinet handle Level meter Inner tub Lint filter(Installed by user) hanging hole for the drain hose Filter cover Control panel film back cover Front control board Adjustable foot seam Pulsator Cabinet Drain hose Adjustable foot Rear fixed foot Meaning and description of the symbols Accessories Bottom plate (1 piece) The end con
Safety precautions Please insert the power cord into special receptacle with rated voltage.Be sure to use single-phase three pins receptacle. The earthing terminal must be earthed reliably.If possible,please adopt electric leakage protector. Before using In normal usage of the washing machine, the power plug shall be ready to be pulled or plugged with hand.
Safety precautions Before using Do not put hand into the rotating tub. It is dangerous even if the rotation speed is slow. Take special care of the children. Keep children away from the washing machine to avoid them climbing on it. Do not decompose, repair or alter the machine by yourself. Do not put any hot or heavy items (such as the kettle with hot water) on the washing machine. Do not wash laundries with volatile materials (such as thinner, petrol etc.).
Before using Safety precautions Please install and adjust the machine according to the requirement of the manual, which is very important for you to operate the machine safely and properly. Install the bottom plate After opening the package, please lean the washing machine gently down on soft items Back (like towel cloth, blanket, etc.). Install the bottom plate to the bottom of the machine Front with eight screws by a cross screwdriver, then lift the machine up gently.
Before using Install the lint filter After opening the package, please take out the lint filter from the document bag, install it to the filter cover of inner tub. See to the figure. Inner tub Lint filter How to change the direction of the drain hose 1.Dismount the back cover of thewashing machine. 2.Lay down the washing machine gently with thefront side facing the ground. Use cross screwdriver to loosen the eight screws. Take offthe bottom plate. back bottom plate 4.
Install the water inlet hose Before Using Install the water inlet pipe Water faucet, suitable water faucet, not suitable It is required that the front end shall be longer than 10mm. The outlet end surface of the faucet shall be flat and smooth. If not, please file it smooth to avoid leakage. Connection between the water inlet hose jointer and the water faucet 1.Press the lower end of the lock lever and push down the slider. Take off the water inlet hose jointer from the water inlet hose component.
Before Using Connection between the water inlet hose jointer and the water inlet hose 1 Push down the slider. Plug the water inlet hose into the jointer. 2 Hang the lock lever onto the jointer. Release the slider till a click sound is heard. Locking level The water inlet hose jointer Slider Check the connection between the water inlet hose jointer and the water faucet 1.Swing the hose gently to check if it is fastened stably. 2.After installation, open the faucet to check if it leaks water. 3.
1Preparation before washing Using process Preparation before washing 1 Connect the water inlet hose. Open the water faucet. 2 Confirm that the washing machine is earthed reliably. Then plug the power plug into the receptacle. The earthing terminal shall not link to gas pipeline and faucet water pipeline. 3 Put down the drain hose. Earth Pay attention to the followings before washing Check if the laundries have special requirement on washing Clear the pocket. Take out the coins, sand, hairpins etc.
2 Put in the laundries Using process The capacity of washing and spinning refer to the largest weight of the standard laundries under dry condition that can be washed or spinned in one cycle. Washing quantity for one cycle shall be less than the rated capacity.The largest capacity of this machine is 7.0kg. The thickness, size and type of the cloth will influence the actual washing capacity.
3 Add the detergent and softener Using process Put the washing powder and softener into the detergent box directly as indicated in the left figure. After that, please close the detergent box. Refer to the following table for the usage of the detergent: The standard dosage of the detergent and the water quantity Inlet for concentrated washing powder and detergent Softener inlet Detergent box How to use the whitener Fill water to decided level. Dilute the whitener with container.
4 Use the operation buttons Using process a Description of the function of the operation buttons Mode and meaning of the indicator Flash: indicating the running mode On: indicating the mode about to run Flash rapidly: indicating abnormal situation WATER INLET button In starting the machine, it is set to COOL WATER automatically Push the button to select one from the three modes of COOL WATER only, both WARM WATER and COOL WATER, or hot water only.
Using process START/PAUSE button Digitron During sensing, it displays -During operation of programs, it displays the remained time (minute) During reserve procedure, it displays the remained reserve time (in hour) In case of abnormal phenomenon, it displays the abnormal symbol (see to Page 16) After the power is switched on, push it to start the machine During working, push it to pause working. During pause, push it to resume working. POWER ON/OFF button Push the On/Off button to switch on the power.
Using process B Steps of using the operation buttons and description of each step. BALANCE DISPLAY FUZZY STRONG COOL MIN SURPLUS WARM STANDARD SOAK NIGHT WASH GENTLE RINSE FAST SPIN POWER ON/OFF RESERVE HOURS LATER SOFT WATER INLET WATER LEVEL CURRENT RESERVE PROGRAM SELECT START PAUSE 1 Push the POWER ON/OFF button to switch on the power. POWER ON/OFF 2 Push the program button to select suitable automatic program.
Using process Attention Even there's no water in the tub, a certain period is required before spin starting. Do not use the SOAK program for the woolen textiles. Separate the laundries that are not colorfast from other laundries in washing. Procedure selection method Times of pushing the Selected procedure SELECT button Applicable circumstance Contents (the lighted indicators indicate the programs about to run) WASH - SPIN When the common laundries need washing, rinsing and spinning.
Using process Water Level and Time Table of Each Program Program Water level Wash (minute) Standard Night Gentle Fast About 4 About 3 Rinse (minute) Rinse twice Spray twice, rinse once Rinse once Rinse once Spin Total time (minute) (minute) Soak included Soak excluded About 5~6 About 83~45 About 48~30 About 6~8 About 99~55 About 65~40 About 2 About 2 About 21~17 About 10 * Total time: including the normal water inlet time and drain time.
7 Disposal After Washing Using process Please take off the detergent box and wash it with water Lint filter: 1.How to take it off: Pull it upwards slantingly and gently. 1.Pull it up to dismount. 2.How to install: Put it in from the top slantingly, then push 2.Push it down to install it. it in to the right position. Dismount 3.
Trouble-shootingAnswers to questions (If there's breakdown, please pull off the power plug before checking) The following phenomena are not breakdowns sometimes. Please confirm again before sending it to repair. If there are real breakdowns, please come to the special maintenance department or after-sale service department of our company. Do not repair it by yourself. Phenomenon It rings after starting the reserve function. The digitron displays E0. The drainage cannot work, or is too slow.
Packing list Name Quantity Storage position User's manual 1 piece Inside the document bag Lint filter 1 piece Inside the document bag Water inlet hose component 2 pieces Inside the accessory bag Bottom plate 1 piece Between the upper cushion of the washing machine package and the upper seal of the package carton Tapping screw 8 pieces Inside the accessory bag Fuzzy logic automatic washing machine 1 set
Specifications Model HWM70-A Rated voltage frequency 220V ~ 60Hz Rated washing / spinning capacity 7.0kg Water level/Water quantity (about) 1/23L, 2/30L, 3/34L, 4/40L, 5/44L, Max water consumption About 186L (the highest water level, standard program) 0.03MPa-0.78MPa (when water temperature is 70 ~90 , the water inlet pressure of hot water shall not exceed 0.
