HWF95AN1 HWF85AN1 HWF75AN1 HWF85ANB1 HWF95ANB1 NZ AU
Thank You NZ AU Thank you for purchasing a Haier Product. Please read these instructions carefully before using this appliance. The instructions contain important information which will help you get the best out of the appliance and ensure safe and p roper installation, use and maintenance. Keep this manual in a convenient place so you can always refer to it for the safe and proper use of the appliance.
NZ AU Content 1-Safety information ........................................................................................................................... 4 2-Product description......................................................................................................................... 7 3-Control panel .................................................................................................................................... 8 4- WiFi connection & Remote mode.....................
1-Safety information Bef ing safety hints! NZ AU - WARNING! ▶ ▶ ▶ ▶ Make sure there is no transport damage. Make sure all transport bolts are removed. Remove all packaging and keep out of children´s reach. Handle the appliance always with at least two persons because it is heavy.
NZ AU 1-Safety information WARNING! Daily use ▶ Do not remove or insert the plug in the presence of flammable gas. ▶ Do not hot wash foam rubber or sponge-like materials. ▶ Do not wash any laundry which is polluted with flour. ▶ Do not open detergent drawer during any wash cycle. ▶ Do not touch the door during the washing process, it gets hot. ▶ Do not open the door if the water level is visibly over the porthole. ▶ Do not force the door to open.
1-Safety information NZ AU WARNING! Installation ▶ Install or use the appliance only where the temperature is above 5 °C. ▶ Do not place the appliance directly on a carpet, or close to a wall or furniture. ▶ Do not install the appliance in direct sunlight or in the near of heat sources(e.g. stoves, heaters). ▶ Make sure that the electrical information on the rating plate agrees with the power suppl y. If it does not, contact an electrician. ▶ Do not use multi-plug adapters and extension cables.
2-Product description NZ AU Note: - 2.1 Picture of appliance Front (Fig. 2-1): Rear side (Fig. 2-2): 1 2 3 2 3 4 1 5 6 2-2 Temp.
NZ AU 3-1 take HWF95AN1 as an example Refresh 8 3-2 3-3 3-4 Press to turn the washer ON/OFF. Press and hold the Power button for five seconds until the power is turned on and the APP will be displayed on the screen to turn on the network function.
NE AU 3.4 Detergent drawer Open dispenser drawer,the following components can be seen (Fig. 3-5): 1: compartment for powder or liquid detergent. 2: compartment for laundry aid products such as powder stain removers and soaking agents. 3: compartment for softener. 4: lock tab, press it down to pull out dispenser drawer. The recommendation on the type of detergents is suitable for the various washing temperatures, please refer to the manual of detergent (see P11). 3-5 4 1 M AX AX M 2 3 3.
3-Control panel 3.5.4 Function button”Speed Up” 3-10 Touch the button (Fig. 3-11) to reduce washing time. When select” speed up” function, the weight of the laundry is less than the normal weight. Speed Up 3.5.5 Function button”ECO” 3-11 Touch the button (Fig. 3-11) to use the ECO option to save water and energy. ECO 3.5.6 Function button”Spin Speed” 3-12 Touch this button (Fig. 3-12) to change the spin speed of the programme. If “ 0 ” is selected, the laundry will not spin. Spin Speed 3.
4-WiFi connection & Remote mode NZ AU Your appliance can be connected to your home wireless network and operated remotely using the app. Ge ng started Ensure your home WiFi network is turned on. You will be given step by step guidance on both your appliance and mobile device. It may take up to 10 minutes to connect your appliance. On your mobile device: 1. Your product is WiFi connectable. Please visit the webpage below to download the app and find out more: Australia https://www.haier.com.
5-Programmes NZ AU Detergent compartment for: 1 AX M AX M / No Temperature in °C 1) selectable range Cotton 7.5/8.5/9.5 * to 90 20 Synthetic 7.5/8.5/9.5 * to 60 30 2/2/2.5 * to 30 30 7.5/8.5/9.5 * to 90 60 / / * to 90 60 Delicate Towels Refresh 1 3) 7.5/8.5/9.5 Allergy 5/6/7 * to 90 30 1 * to 40 * Bulky 6/7/7 * to 60 40 Spin 7.5/8.5/9.5 / / Durable 7.5/8.5/9.
6-Consumption NZ AU Check the energy label for energy consumption information. The actual energy consumption may differ from the declared one according to local conditions. The standard 60°C and 40°C cotton programmes are suitable to clean normally soiled cycle temperature. Actual water temperature may differ from declared Note: Auto Weight The appliance is equipped with a loading recognition. At low loading, energy, water and washing time will be reduced automatically in some programmes.
7-Daily use 7.1 Power supply Connect the washing machine to a power supply (220V to 240V~/50Hz; Fig. 7-1). Please refer also to section INSTALLATION (see P29). NZ AU 7-1 7-2 7.2 Water connection ▶ Before connecting check the cleanliness and clarity of the water inlet. ▶ Turn on the tap (Fig.7-2). Note: Tightness Before use check for leakage in the joints between the tap and the inlet hose by turning on the tap. 7.
7-Daily use NZ AU Care chart Washing Washable up to 95°C normal process Washable up to 60°C normal process Washable up to 60°C mild process Washable up to 40°C normal process Washable up to 40°C mild process Washable up to 40°C very mild process Washable up to 30°C normal process Washable up to 30°C mild process Washable up to 30°C very mild process Wash by hand max.
7-Daily use NZ AU 7.5 Selecting detergent ▶ ▶ ▶ ▶ ▶ Use only machine wash approved detergent. . See tips for countertop detergent stickers. Do not use dry cleaning agents such as trichloroethylene and similar products.
7-Daily use NZ AU 7-4 7.6 Adding detergent M AX 1. 2. M AX 3. Slide out the detergent drawer. Put the required chemicals into corresponding compartments (Fig. 7-4), Push back the drawer gently. Note: ▶ ▶ ▶ ▶ ▶ ▶ ▶ Remove detergent residues before next wash cycle from the detergent drawer. Do not overuse detergent or softener. Please follow the instruction on the detergent package. Concentrated liquid detergent should be diluted before adding.
7-Daily Dai ly use 77.10 Start wash programme Touch“Start/Pause“ button (Fig. 7-8) to start. The LED of the”Start/ Pause“ button stops flashing and lights up continuously. Appliance operates according to present settings. Changes are only possible by cancelling the programme. NZ AU 7-8 7.11 Interrupt / cancel wash programme To interrupt a running programme press gently “Start/Pause“. The LED above the button is flashing. Press it again to resume operation.
NZ AU 8-Eco-friendly washing Environmentally responsible use ▶ To achieve best use of energy, water, detergent and time you should use the recommended maximum load size. ▶ Do not overload (hand width clearance above laundry). ▶ For slightly soiled laundry select the Express 15 programme. ▶ Apply exact dosages of each washing agent. ▶ Choose the lowest adequate washing temperature-modern detergents are efficiently cleaning below 60°C. ▶ Raise default settings only due to heavy staining. ▶ Select max.
9-Care and cleaning NZ AU 9.1 Cleaning the detergent drawer M AX M AX Take always care there are no detergent residues. Clean the drawer regularly (Fig. 9-1): 1. Pull out the drawer until it stops. 2. Press the release button and remove the drawer. 3. Flush the drawer with water until it is clean and insert the drawer back in the appliance. 9-1 2 1 9.2 Cleaning the machine ▶ ▶ ▶ Unplug the machine during cleaning and maintenance Use a soft cloth with soap liquid to clean the machine case (Fig.
9-Care and cleaning NZ AU 9-6 9-7 9.5 Long periods of disuse If the appliance is left idle for a longer period: 1. Pull out the electrical plug (Fig. 9-6). 2. 9 3. Open the door to prevent formation of mould and odours. Leave door open while not used. Before next usage check carefully power cord, water inlet and drain hose. Make sure everything is properly installed and without leaks. 9-8 9-9 9 for instance if the appliance: ▶ Doesn´t drain the water. ▶ Doesn´t spin.
9-Care and cleaning 9. NZ AU 9-14 9-15 (Fig. 9-14). 10. 11. Close service flap. 9 CAUTION! ▶ ▶ 22 water can leak. undamaged.
10-Troubleshooting NZ AU of a problem please check all shown possibilities and follow below instructions before you WARNING! ▶ Before maintenance, deactivate the appliance and disconnect the mains plug from the mains socket. ▶ improper repairs can cause considerable consequential damages. ▶ A damaged power cable should only be replaced by the manufacturer, its service 10.1 Information codes Following codes are displayed only for information referring to the washing cycle. No measures must be performed.
10-Troubleshooting Problem Cause NZ AU Solution F3 Temperature sensor error. Contact the After sales service. F4 Heating error. Contact the After sales service. F7 Motor error. Contact the After sales service. FA Water level sensor error. Contact the After sales service. FC0, FC1 or FC2 Abnormal communication error. Contact the After sales service. Unb Unbalanced load error. Check and balance laundry load in the drum. Reduce the load. 9.
10-Troubleshooting NZ AU Problem Cause Excessive foam in drum or detergent drawer. • Detergent is not a appropriate. • Detergent is too concentrated. • Check detergent recommendations. • Dilute detergent. Au tomatic adjustment ment of washing time. • Washing programme duration will be adjusted. • This is normal and doesn‘t affect functionality. Spinning fails. • Unbalanced of laundry. • Redistribute load and run a spin program again. • Cycle was not selected for the soil level in the garments.
11-Installation NZ AU 11.1 Preparation ▶ Take the appliance out of the packaging. ▶ keep them out of childrens reach. While opening the package, water drops may be seen on plastic bag and porthole. This normal phenomenon results from water tests in the factory. Note: Packaging disposal Keep all packaging materials out of children´s reach and dispose them in an environmentally friendly manner. 11.2 OPTIONAL: Install noise reduction pads 2. 1. 1.
11-Installation NZ AU 11.4 Moving the appliance If the machine is to be moved to a distant location,replace the transportation bolts removed before installation to prevent damage: The assembly takes place in reverse order. 11-7 11.5 Aligning the appliance Adjust all feet (Fig. 11-7) to achieve a complete level position. This will minimize vibrations and thus noise during use. It will also reduce wear and tear. We recommend to a spirit level for adjustment. Floor should be as stable and flat as possible.
11-Installation NZ AU 11.6 Drain Water Connection Fix the water drain hose properly to the piping. The hose has to reach at one point a height between 80 and 100 cm above the appliance bottom line! If possible keep always drain WARNING! ▶ ▶ ▶ ▶ Use only the supplied hose set for the connection. Never reuse old hose sets! Only connect to cold water supply. Before connection, check whether the water is clean and clear. Following connections are possible: 11.6.
11-Installation NZ AU 11-11 11-12 11.7 Fresh Water Connection Make sure that the gaskets are inserted. 1. 2. Connect the water inlet hose with the angled end to the appliance (Fig. 11-11). Tighten the screw joint by hand. The other end connect to a water tap with a 3/4” thread (Fig. 11-12). 11.8 Electrical Connection 11-13 Before each connection check if: ▶ power supply, socket and fusing are appropriate to the rating plate. ▶ the power socket is earthed and no multi-plug or extension are used.
12-Technical data NZ AU 12.1 Additional Additional technical technical data data 11.1 HWF75AN1 HWF10AN1 HWF95AN1 HWF80AN1 /HWF95ANB1 HWF85AN1 HWF90AN1 /HWF85ANB1 Voltage in in V V Voltage 220-240 V~/50Hz V~/50Hz 220-240 Current in in A A Current 10 10 Max power power in in W W Max 1900 Water pressure pressure in in MPa MPa Water Net weight inin kgkg Netto weight 1900 2000 0.03≤P ≤1 ≤1 0.03≤P 70 80 70 77 71 70 12.2 Product Product dimensions dimensions 11.
NZ AU 13-Customer service We recommend our Haier Customer Service and the use of original spare parts. ： ▶ your local dealer. ▶ and FAQs and where you can activate the service claim. To contact our Service, ensure that you have the following data available. The information can be found on the rating plate. Model ____________________ Serial No. _____________________ Also check the Warranty Card supplied with the product in case of warranty. contact our Customer Care Centre according to Warranty Card.
0020507792V
