2-Place Setting Dishwasher DW100T Code: 0120501826
Safety Is Very Important - If the supply cord is damaged ,it must be replaced by the Carefully read the instructions contained in this manual, as it provides information that is essential to safe and proper installation, manufacture, a service agent of similar qualified persons in order to avoid a hazard. use and maintenance of this appliance. - The appliance is not instruct for use of young children of infirm persons without supervision.
Close-up View (Interior) A B C D E F G Upper Rack Rack Height Adjustor Top Spray Arm Bottom Spray Arm Washing Filter Detergent and Rinse Aid Dispenser Lower Rack Technical Characteristics Width 60 cm Depth 60 cm Height 85 cm 12 standard place settings Capacity Mains water pressure 0.03-0.6 MPa Power voltage 220-240V~ 50Hz Total absorber power 2100W .2.
Detergent and Rinse Aid Detergent Rinse Aid Detergent specifically intended for use with dishwashers must This product makes dishes sparkle and helps them to dry without spotting. The dispenser is located on the inside panel of the be used. The dispenser must be refilled before the start of each wash cycle following the instructions provided in the "Wash Cycle door and should be filled after every 80 wash cycle (or when the rinse aid indicator light comes on for models with this feature). Table.
Loading the Dishwasher Before placing the dishes in the dishwasher, remove the larger Lower Rack food particles to prevent the filter from becoming clogged. If the pots and pans have baked-on food that is extremely hard Upper Rack to remove, we recommend they are soaked before washing. This will eliminate the need for extra wash cycles. Pull out the rack to load the dishwasher. The lower rack Place the most difficult to clean items on the bottom rack: pots, pans, lids, serving dishes and bowls.
Turning on the Appliance Starting a wash cycle Wait a few minutes before unloading the dishwasher to avoid - Make sure that the appliance is plugged in and switched on. - Make sure that the water supply is turned on. handling the dishes and utensils while they are still hot and more susceptible to breakage. They will also dry better. - Load the detergent (see the section entitled, "Detergent and Rinse Aid" on page 3).
Energy Saving Tips - It is important to try and run the dishwasher when it is fully loaded - Use the right amount of detergent: if you use too much detergent, the result will not be cleaner dishes, but, rather, a greater nega- to save on energy. tive impact on the environment. - Rather than run a full cycle for a half load, you can run the Prerinse cycle which will prevent odours from forming and food from caking onto the dishes.
Wash Cycle Table CYCLE Heavy TYPE OF LOAD Very dirty dishes, pots and Cold pre-wash. pans. Cold rinse. DETERGENT RINSE AID 30g 25g Extended 50 `=wash. O (Not to be used with delicate items). Normal DESCRIPTION OF CYCLE Hot rinseK Drying. Normally load of dirty dishes, Cold rinse. pots and pans. Standard Extended 50O`=wash. daily cycle. Hot rinseK Drying. For dishes that only require Hot rinseK a rinse and dry. Drying.
Cleaning and Special Maintenance Filter Assembly Cleaning the Spray Arms For the best performance and results, the filter assembly must Food particles may become encrusted on the spray arms and block the hole (see "Close up view [interior]" on page 3, letters be keep clean. The filter removes food particles from the wash water, allowing C-E ). Check the spray arms periodically and clean them when needed. the water to be recirculated during the cycle.
Installation Drain Hose Connection Insert the drain hose into a drain pipe with a minimum diameter Positioning the Appliance Position the appliance in the desired location. The dishwasher is equipped with water supply and drain hoses that can be posi- of 40mm, or let it run into the sink. Use the plastic support that comes with the appliance (see fig .2) and ensure there are no tioned to the right or left to allow correct installation. tight bends or kinks.
Installation Diagram WR: Wiring box IG: Power switch IS: Door switch P1: Water level switch LS: Power indicator PS: Drain pump EV1: Inlet valve D-Ed: Dispenser TS.
