Mounting Instructions Item No.: 372.68 Series and 372.
Foreword By choosing the verso/strato lift-up fitting, you have opted for a fitting solution that is technically very advanced and mechanically very efficient. Your verso/strato lift-up fitting is manufactured with extreme care and precision and goes through numerous quality and safety checks in order to ensure that it operates smoothly and safely. 1. IMPORTANT SAFETY NOTICE Installation must be carried out in accordance with the assembly instructions; otherwise there is a risk of injury. 2.
Overview on construction sizes for lift-up fitting – verso Cabinet height 420 - 800 mm 1 huwiliftverso strato 4 min. 138 ca. 55 ca. 40 54 4 49 40 ca. 110 41 4 44 4 ca. 275 View of right side. (left side symmetrical) 59 74 4 69 4 64 4 79 4 255 min. 33 ca. 15 ca. 40 ca. 65 ca. 95 +0.5 3 ca. 575 ca. 533 ca. 495 ca. 450 ca. 410 ca. 365 ca. 325 ca. 255 ca. 280 ca. 380 32 32 32 420 – 800 ca. 120 ca. 145 61 13.5 4 ca.
2 Overview on construction sizes lift-up fitting – strato Cabinet height 342 - 650 mm strato View of right side. (left side symmetrical) T H W 28 40 min. 33 R Y X U 32 32 32 D [ mm ] mm X Y D H ca. R ca. T U ca. V W min. 342 186 308 295 28 338 200 50 151 350 186 308 295 36 346 200 50 151 420 186 308 295 98 408 200 50 151 420 255 380 395 5 414 265 37 138 450 255 380 395 35 444 265 37 138 500 255 380 395 85 494 265 37 138 500 293.
Drill holes for fitting in accordance with the drilling diagram. Lift-up fitting verso/strato verso View of right inner side. (left side symmetrical) Design for all cabinet heights W 32 Drilled holes A= Ø 5 mm x min. X deep V 32 40 72 19 15 Drilling depth Ø5 Ø5 16 12 96 3 168 A Schrankhöhe Cabinet height Hauteur de meuble Altezza armadio Altura del mueble [ mm ] V W min.
Drill holes for flap according to the drilling diagram. huwiliftverso strato Design for particle board and MDF board.
Drill holes for flap according to the drilling diagram. huwiliftverso strato 255 255 A* Design for 20 mm aluminum profile. 8 Ø3.
Drill holes for flap according to the drilling diagram. Lift-up fitting – strato strato B* Y Y A* A* Design for particle board and MDF board. B* B* Drilling diagram for reverse side of flap 13.5 13.5 32 32 32 32 32 32 X C A* and B* = observe overlay! C = Drilling depth 19 15 Ø5 16 12 Ø5 6 8 X Y 342 – 420 mm 186 mm 420 – 500 mm 255 mm 500 – 550 mm 293.5 mm 550 – 650 mm 313.
Drill holes for flap in according to the drilling diagram. Lift-up fitting – strato strato Design for 20 mm aluminum frame profile. Y Y A* Cabinet height 420-650 mm 32 8 32 32 Ø3.2 (M4) 32 Drilling diagram for reverse side of flap 32 32 X A* = observe overlay ! A* 7 9 X Y 342 – 420 mm 186 mm 420 – 500 mm 255 mm 500 – 550 mm 293.5 mm 550 – 650 mm 313.
8 Screw on fixation brackets. verso Design for particle board and MDF board. Design for aluminum frame profile. Left and right side on flap.
9 Screw on the base fixing plate and right/left adapter-plate. verso View of right side wall.
10 Install transversal stabilization bar. Lift-up fitting verso/strato 1 verso 2 1 5 2 3 1 1 3 3 Visual control: Has compression spring 1 fitted in traction lever 2? (If not, please do so.) Slightly loosen clamp screws 3. Connect traction lever 2 and stabilization bar 5.
2 6 5 2 3 6 7 6 = 0 mm ! 3 Press traction lever 2 / stabilization bar 5 together (Spring tension) and engage successively with axis pieces 6 traction lever bearing 7. Fit into the cabinet without free play. Tighten both clamp screws 3 (2-4 Nm).
11 Screw on fitting. verso The fitting can be used for both sides (right and left). Attention! The lifting arm of the fitting must be in the open position (supply condition) as otherwise there is a risk of injury! Fitting is under spring tension.
12 Install regulation part on the lifting arms. verso strato 1 View of right side. (left side symmetrical) 2 3 4 The regulation part can be used for both sides (right and left). Connect regulation part 1 and lifting arm 2 with bolt 3 and secure with fixation clip 4.
13 1 Connect traction lever. verso View of right side. (left side symmetrical) verso 3 1 2 Connect traction lever 1 with regulation part 2 and secure with fixation clip 3.
Lift-up fitting strato strato View of right side. (left side symmetrical) 2 1 3 Connect traction lever 1 with regulation part 2 and secure with fixation clip 3.
14 Attach cabinet flap. Lift-up verso/strato 1 verso For all designs. View of right side. (left side symmetrical) verso Hang in cabinet flap and secure with screw 1. For adjusting reasons the cabinet flap must have some free play, do not fully tighten the screw.
15 Fine-adjustment of the flap height Lift-up fitting verso/strato 1 verso strato View of right side. (left side symmetrical) Height fine-adjustment The height adjustment of the cabinet flap is done through the excenter screw at the fitting (see scale). Please loosen fixing screws. max.
16 Fine-adjustment according to flap alignment. Lift-up verso/strato 1 verso strato View of right side. (left side symmetrical) Lift-up fitting verso 1 3 2 Fine-adjust The fine-adjust according to flap alignment is done by means of the excenter screw 2 on the regulation part. Tighten the fixing screw 1 after adjustment. LIft-up fitting strato max.
17 Fine-adjust according to flap inclination. Lift-up verso/strato 1 verso strato View of right side. (left side symmetrical) 7 + SW 19 Ø4 / SW 4 + - - Inclination of the flap in closed position The flap inclination is adjusted at the excenter 7 of the receptive base plate for the traction lever.
18 1 Adjust the final stop of the cabinet flap. verso strato SW 8 min. 9 mm max. 15 mm The adjustment of the final stop (abt. 12 mm), pre-set by the factory, is done through the stop-screw. To do this pull the lifting-arm / flap slightly downwards.
19 1 Power adjustment of the cabinet flap weight. verso The power-adjustment for the flap weight is done through the hex screw. (See scale) To do this pull lifting arm / flap downwards and adjust as shown. kg max. max. 20 mm min.
20 1 Carry out functional test. verso strato If everything has been adjusted correctly the flap will stop in any position from 20 cm opening and on. 21 Install the housing-cover.
22 1 Choosing the correct verso model. huwiliftverso strato The correct model results from the height and weight of the flap, see chart. Choose the transversal stabilization bar according to the width of your cabinet. Verso (without transversal stabilization bar) Cabinet height Flap weight [ mm ] [ kg ] Part-No. 420 – 550 2.0 4.0 6.0 8.0 4.0 8.0 10.0 17.0 03.3684.001.001 03.3684.001.002 03.3684.001.003 03.3684.001.004 550 – 650 2.0 3.5 6.0 9.0 3.5 7.0 10.0 16.0 03.3684.001.001 03.3684.001.
huwiliftverso strato Transversal stabilization bar for verso Cabinet width Side wall thickness Bar length [ mm ] [ mm ] [ mm ] 600 900 1200 Part-No. 16 490 04.3684.801.000.0490.00 19 16 484 790 04.3684.801.000.0484.00 04.3684.801.000.0790.00 19 16 784 1090 04.3684.801.000.0784.00 04.3684.801.000.1090.00 19 1084 04.3684.801.000.1084.00 Further versions on request. We reserve the right for technical modifications.
23 1 Choosing the correct lift-up fitting strato model. strato The correct model results from the height and weight of the flap, see chart. Choose the transversal stabilization bar according to the width of your cabinet. LIft-up fitting strato (without transversal stabilization bar) Cabinet height Flap weight / Part-No. [ mm ] [ kg ] 342 342 – 420 1,5 – 4,0 03.3685.011.001 4,0 – 7,2 03.3685.011.002 6,5 – 11,5 03.3685.011.003 — 420 420 – 500 2,0 – 3,5 03.3685.012.001 3,5 – 7,0 03.3685.012.
strato Transversal stabilization bar for strato Cabinet width [ mm ] Side wall thickness [ mm ] 600 900 1200 Bar length Part-No. [ mm ] 16 490 19 16 484 790 19 16 784 1090 19 1084 Further versions on request. We reserve the right for technical modifications. 3901 Cheyenne Drive P.O. Box 4000 Archdale, NC 27263 1-800-423-3531 www.hafele.com 04.3684.801.000.0490,00 04.3684.801.000.0484,00 04.3684.801.000.0790,00 04.3684.801.000.0784,00 04.3684.801.000.1090,00 04.3684.801.000.
