JENSON Gloss 937/4610 940/4597 Spare Parts Customer Support Visit: www.argos-support.co.uk Call: 0345 640 2020 Email: Help@ClickSpares.co.
Safety Important - Please read these instructions fully before starting assembly • Warning: This unit weighs approximately 66kgs. Please lift with care. • During assembly children should be kept away from the product due to possible risk of injury. • Installation shall only be carried out exactly according to the manufacturer’s instructions otherwise a safety risk can occur if incorrectly installed. • Do not use this item if any components are missing or damaged.
76.4 x 6cm x 2 67.7 x 77.4cm 7 76.4 x 41.3cm 3 76.4 x 41.4cm 6 79.8 x 45cm 8 63.7 x 39.3cm DF-00023249 DF-00021905 5 DF-00023248 73.3 x 42.9cm XDF-00022863 4 2 DF-00013263 73.3 x 42.
Fittings Use these drawings to correctly identify the fittings J x2 G x4 x4 E F63 F110 D H x8 x5 I x4 F328 x7 x 12 F474 F C F137 x 12 F639 B F51 F901 F900 F22 x 16 A A F646 Main Bag K x4 Tools Only used for drilling walls
1 A x6 2 Finished front edges 1 2 B x4 2 1 3 C x8 2 1
4 B x4 A x6 3 Finished front edge 5 x2 1 3 Finished front edges
6 A 7 x4 B x4 4 4 x2 1 4 4 8 x4 2 Finished front edge
9 D x4 10 5
11 Squaring up a Chest and fitting the Back Panel www.youtube.com/watch?v=FeaI6541z7o The Back panel must be flush with the Back Rail.
13 C x4 J x2 Only use 1 Screw to fit each Bracket 6 Finished front edge 14 x4 6 IMPORTANT: The Back panel must slot into the groove in the Top panel Finished front edge
15 F x7
16 WARNING! In order to prevent overturning this product must be used with the 2 wall attachment devices provided See the next section for a guide to wall mounting and fixings Top Slide the Brackets against the wall. Fit the 2nd screws supplied with the Brackets into the underside of the Top panel. Mark the slot at the back of the Brackets for drilling into the wall. Wall fixings are not supplied as they will need to suit the wall type.
A Guide to Wall Mounting & Fixings Important note: If plastic wall plugs are supplied with your product: Important: When drilling into walls always check that there are no hidden wires or pipes etc. Make sure that the screws and wall plugs being used are suitable for supporting your unit. Consult a qualified tradesperson if you are unsure. Hints: - these are only suitable for use in masonry walls. If you are in any doubt about the correct wall plugs for your wall, seek professional advice.
17 G x4 18 7 Finished front edge
19 H x8 K x4 Pre-mounted Hinge Fitting & Adjustment https://www.youtube.
21 Pre-mounted Hinge Fitting & Adjustment https://www.youtube.com/watch?v=b4NeCGnpjP8 Adjust the Door if required a: a: Height adjustment. Loosen screws A on Hinge Plates and move Door up or down as required. Retighten screw A. b: Forward and Back adjustment. Loosen screw B on Hinge Plate and move door in or out as required. Retighten screw B. A A b: c: Sideways adjustment. To move door ‘out’ loosen screw C. To move door ‘in’ tighten screw C.
