Hayward - Left Shelf TV Unit Assembly Instructions - Please keep for future reference 411/4909 411/5568 Dimensions Width - 38cm Depth - 39cm Height - 58.5cm MADE IN BRITAIN Important - Please read these instructions fully before starting assembly If you need help or have damaged or missing parts, please visit www.argos-support.co.uk or email: Help@ClickSpares.co.uk (quoting your original order number) Alternatively, call the Spares Helpline on: 0370 112 1928.
Safety and Care Advice Important - Please read these instructions fully before starting assembly • Warning: This unit weighs approximately 31kgs. Please lift with care. • Make sure you have enough space to layout the parts before starting. • Check you have all the components and tools listed on pages 2 and 3. • Do not stand or put weight on the product, this could cause damage. • Remove all fittings from the plastic bags and separate them into their groups.
Components - Panels If you need help or have damaged or missing parts, please visit www.argos-support.co.uk or email: Help@ClickSpares.co.uk (quoting your original order number) Alternatively, call the Spares Helpline on: 0370 112 1928. For any other queries please contact the Customer Helpline on: 0345 640 2020 Please check you have all the panels listed below 1 Left Side (DF3372) (41.6 x 37.1cm) 2 Right Side (DF3647) (41.6 x 37.1cm) 3 Left Divider (DF3649) (38.5 x 36.
Components - Fittings If you need help or have damaged or missing parts, please visit www.argos-support.co.uk or email: Help@ClickSpares.co.uk (quoting your original order number) Alternatively, call the Spares Helpline on: 0370 112 1928. For any other queries please contact the Customer Helpline on: 0345 640 2020 Please check you have all the fittings listed below Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.
Assembly Instructions Step 1 J Prepare the left divider Insert 2 large locking nuts B into the left divider 3 . Note: The arrow on the locking nut must point towards the hole in the edge of the panel Fit 2 hinge plates J onto the left divider 3 , making sure that the slot is facing towards the finished front edge. B Finished front edge B J B J a: 3 Turn the left divider over Turn the left divider over A A A A A b: Screw 4 metal dowels .A into the left divider 3 .
Assembly Instructions Step 3 Prepare the 2 fixed shelves x2 B B B Insert 4 large locking nuts B into each of the 2 fixed shelves 8 . B 8 Finished front edge Step 4 A Fit a fixed shelf to the left divider B Push a fixed shelf 8 onto the left divider 3 . Use a screwdriver to tighten the 2 large locking nuts B fitted to the fixed shelf 8 . Note: Turn the large locking nuts B as far as they will go - more than 1/2 a turn.
Assembly Instructions Step 6 B Prepare the base Insert 4 large locking nuts B into the base 7 . F B F F a: M F M M Screw the 4 feet M into the mark holes in the base 7 using screws F . 7 M B B Finished front edge Step 7 Fit the base 3 Attach the base 7 to the left divider 3 using 2 screws E . 7 E E Finished front edge Step 8 Fit the right divider Attach the right divider 4 to the base 7 using 2 screws E .
Assembly Instructions Step 9 B Prepare the left side Screw 6 metal dowels A into the left side 1 . A A Finished front edge A A A B A Insert 2 large locking nuts B into the left side .1 . 1 Step 10 Prepare the right side Screw 2 metal dowels A into the right side 2 . B A B A J Insert 2 large locking nuts B into the right side 2 . 2 J Finished front edge J Fit 2 hinge plates J onto the right side 2 , making sure that the slot is facing towards the finished front edge.
Assembly Instructions Step 12 Prepare the top A A A Screw 8 metal dowels A into the top 5 . A A A A 5 A Finished front edge Step 13 Fit the top Note: To make it easier to fit the top, place polystyrene blocks from the packaging underneath the side and divider panels to raise the assembly. 2 4 Push the top 5 onto the assembly. Use a screwdriver to tighten the 8 large locking nuts B fitted to the left side 1 , right side 2 , left divider 3 and right divider 4 .
Assembly Instructions Step 14 a: Fit the back The measurement from top corner X to bottom corner X must be equal to the measurement from top corner Y to bottom corner Y a: Square up the unit by b: making sure that measurement x to x equals y to y. b: Place the back x 11 onto the unit. C y Nail C around the outside edges of the back 11 and into the back edge of the right divider 4 , as shown. 11 4 y Note: Nails should be spaced about 150mm apart.
Assembly Instructions Step 16 Fit the shelf studs For each of the 2 loose shelves 6 , insert 4 shelf studs D . D x4 D x4 Step 17 Fit the 2 loose shelves 6 Lower the 2 loose shelves 6 down onto the shelf studs D . 6 Step 18 H Prepare the 2 doors H H Push fit 2 hinges K into each of the doors 9 and 10 . H 9 K K Secure each hinge with 2 screws H . Note: Before securing with the screws, make sure that the hinges are positioned at 90 degrees with the edge of the door.
Assembly Instructions Step 19 Fit doors and handles a: J K onto the front part of the hinge plate J . The recess at the bottom of screw B goes into the slot in the hinge plate. b: Keep the hinge J K K A Note: The easiest way to attach each door 9 and .10 is to fit the top hinge first, then align and fit the other hinge. a: Push the hinge b: J K B c: d: J J K K B K FLAT against the hinge plate J as you slide it across as far as it will go. Tighten screw A.
Assembly Instructions Step 20 Adjust the doors if needed a: a: Before adjusting the doors, use a spirit level to check the base (or top) of the unit is level, front-to-back and side-to-side in the 3 positions shown. Use suitable packing pieces (not supplied) to make the unit level BEFORE making any adjustment to the hinges, as shown. b: A A b: Height adjustment. Loosen screws A on hinge plates and move door up or down as required. Retighten screw A. c: B c: Forward and Back adjustment.
Assembly Instructions Step 21 Assembly is complete If you need help or have damaged or missing parts, please visit www.argos-support.co.uk or email: Help@ClickSpares.co.uk (quoting your original order number) Alternatively, call the Spares Helpline on: 0370 112 1928.
ALR3144
