User’s Manual Bluetooth Adapter (Bluetooth adapter for a glucometer) BA-300 Johnson&Johnson(Lifescan) Version 1.0 (2016.
USA-Federal Communications Commission (FCC) This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules.
Welcome Thank you for purchasing Bluetooth adapter (BA-300). The Bluetooth adapter is a data transmitter that receives data from a glucometer and sends the data to other devices such as a mobile phone, a gateway, etc. via Bluetooth. The Bluetooth adapter can be connected to Lifescan(Johnson and Johnson)’s OneTouch Ultra and OneTouch Mini/Easy and OneTouch Ultra2.
Descriptions ③ ⑤ ② ④ ① ① Body ② Cable ③ Connector: Connector to a glucometer ④ Red button: A button used for Bluetooth pairing or manual data transfer ⑤ LED: 2-color(Green and Red) LED ⑧ ⑥ ⑦ ⑥ Label BA-300 ⑦ Dry cell cover: Cover below which dry cells are put ⑧ Mode Select 4
⑨ ⑨ Hidden button: A hidden button used for Bluetooth pairing How to Use 1. [Preparation] Insert batteries. Open the cell cover to place AAA 1.5V 2 EA while checking the polarity (+,-) and then close the cover. 2. Connect the cable to a glucometer [Bluetooth pairing] Bluetooth pairing is an authentication process between a Bluetooth adapter and a target device that readings are supposed to be sent to.
Supported firmware All version Action Press the Hidden button BT device name AMC_JandJ Pin CODE 1234 Version 1.2 or later versions Press and hold the Red button on the top cover until the LED turns RED (for more than 5 seconds) H3GMA_(Model)_(FW version)_(BT address) 9314 * Notes Model: JandJ FW version: X.X (e.g. 2.0) BT address: The last 3 hexas, that is, 6 digits. For example, A1B2C3. Table 2-1 The detailed steps are as follows: ① Let the device be pairing mode.
Figure 1 Sample procedure of Bluetooth pairing with H3 GPRS gateway(H3G-700) 3. [Automatic data transfer] Measure blood glucose while the adapter is being connected to a glucometer. The adapter wakes up and starts downloading data from the glucometer. At the wake-up, you can see “PC” on the glucometer display. The measured data is automatically transmitted to the paired target device such as a mobile phone, a gateway, etc.
If the data transmission succeeds, the Green LED blinks three(3) times and if fails, the Red LED blinks five(5) times. It may take more than 10 seconds for the first trial after replacing the batteries. For OneTouch Ultra, the Red LED keeps blinking until the glucometer shuts off after data transfer. Notes Only normal readings will be transmitted. Control solution readings and erroneous readings will not be transmitted. “HI” and “LO” readings will be transmitted.
Figure 2 Sample procedure of data transmission to H3 CDMA gateway(H3G-800) 4. [Manual data transfer] Press the Red button of the Bluetooth adapter while a glucometer and the adapter are being connected. The adapter wakes up and starts downloading data from the glucometer. At the wake-up, you can see Green LED’s short flashing and “PC” on the glucometer display. The readings will be downloaded and sent to the target device.
Even in the case that there is no reading unsent in the glucometer; the adapter connects to the target device via Bluetooth. But it disconnects soon. 5. The others are the same as those for automatic data transfer. This feature can be used for troubleshooting. [Automatic Wake-up Mode] In the state of connection with OneTouch Easy/Mini or OneTouch Ultra2, this adapter reads data and transfers the unsent readings once every 3 hours. 6.
Cautions Be sure to carefully read the user’s manual before use. Keep the Bluetooth adapter in a clean and dry place away from dust or corrosive gases as well as away from fires Do not apply any shock or vibration to the product Do not rub the product with inflammable such as alcohol, benzene, or acetone the can cause chemical change. Use a dry cloth to prevent the surface from being damaged. Do not stretch nor bend the cable by force. Disassembling the product is not advisable.
Troubleshooting If you have some troubles in data transmission, please check the below Try to do “Manual data transfer” by pressing the Red button while a glucometer and the adapter are being connected. Replace batteries with new ones. Disconnect the glucometer, remove batteries, press the Red button several times, wait for a while, insert batteries again, and connect the glucometer again. And take a reading and confirm data transmission.
Specifications Function: it automatically receives blood glucose data measured from a glucometer and transmits to a pre-determined target device via Bluetooth. Usable devices: Lifescan(Johnson and Johnson)’s OneTouch Ultra, OneTouch Mini/Easy, and OneTouch Ultra2. Bluetooth 4.0 Connectivity to smart phones: Connectivity to Android smart phones is generally available. But the adapter does not support communication with iPhones. Maximum storage: 500 readings.
Revision notes Version 1.0 Change descriptions Initial release Date 2016. 5.
