the note at the end of the manual. Historical Background lightweight design which gives it good low-speed handling properties and short-field performance. many of these beloved airplanes are still around today.
SAFETY PRECAUTIONS This product should not be considered a toy, but rather a complicated and sophisticated flying model. Your safety depends on how you use and fly it, if not correctly operated it could cause injury to you or your family members. Children must be accompanied by an adult at all times if operating this product. Not suitable for children under the age of 14. THIS IS NOT A TOY. s problems.
KIT Tools required P1 P2 P4 P3 P21 P5 P12 P6 P14 P15 P16 P17 P13 P11 P18 P7 P8 P9 P20 P19 P10 P22 Please sand all parts before 01 Assemble the Fuselage 01-1 F36-2 F36-4 Align F37-1 F36-4 F36-3 fuselage side 01-3 01-4 Align Align F37-1 Align Align F0-3 F36-4 1
F29 01-5.1 F10 F26 F27 Balsa strip F11 F28 to actual length 01-3 F17 01-5 01-5.3 F21 F22 F21 01-5.4 Blind nuts F23 F18 01-5.
01-8 01-11 01-9 B 01-12 01-13 01-10 Glue 01-14 01-15 01-16 01-17 3
01-18 01-19 P19 01-20 P21 01-21 P12 n P12 02 Assemble the Main Wing # # P11 P11 P14 P5 Pay attention to the direction of the blind nuts Blind 4
# 03 intermediate strut brace fixing Assemble the horizontal and vertical 03-1 03-2 a 03-3 Glue parts T13 to the vertical stabilizer and to each elevator half at the points A,B and C as shown. b c T13 03-4 03-5 A has been drilled into the end of each T13 part. both halves do lie flat.
P22 03-6 the positions shown. nsert the s in 03-7 all 04 Assemble the horizontal and vertical 04-1 04-3 tail wheel to the fuselage Insert the elevator into the rear of the fuselage as shown and glue the elevator joining rod into position. P13 04-2 Horizontal Bend the steel wire onto the tailwheel wire then feed the wire wheel collar 04-5 04-4 the tailwheel and secure with a wheel collar. the rudder as shown.
04-7 04-6 Vertical Tail P22 04-8 05 05-1 Assemble the Landing Gear 05-2 S P18 Outside P20 P6 P18 Outside 05-3 Inside 05-4 P17 P17 Inside 06 06-1 P7 P7 P22 . See note at end of manual.
06-2 Install the servo inside the wing P15 06-3 06-5 P2 P2 Install the wing strut s 06-4 Sand to Sectional view P9 06-6 .
07 Install servos and pushrods inside the fuselage Glue is wire rod and the servo arms after the steel If fitting an I.C. motor then see the steps below for a different servo arrangement.
08 Install the motor mount and electric/IC motor on the other side 10
09 Set and Adjust C.G For initial flights we recommend you balance the model on the 85mm mark to make it more docile. Once you have flown it a few times you can then move it back slightly if you wish, this will make the flying characteristics more agile.
C of G: Aileron : Elevator 10 Install the scale parts Rudder OPTIONAL Install the scale engine parts 12
Wiring Diagram for RC Equipment (Electric powered only) Wiring Diagram for RC Equipment (IC Engine only) Engine Throttle RX 13
Elevator SIDE VIEW SIDE VIEW Aileron to the right FRONT VIEW to the left FRONT VIEW Rudder Rudder stick to the right FRONT VIEW Rudder stick to the left FRONT VIEW Note: This instruction manual shows the construction of the wooden airframe and the installation of the RC equipment. Prior to complete assembly we recommend that each component is covered separately first with the iron on covering of your choice.
