User Manual

You may change the H.King's settings for BATTERY
TYPE, BRAKE BEHAVIOR, and MOTOR DIRECTION.
You may change these settings using your radio and
receiver. To change settings with your receiver,
start with the motor battery unplugged and the
transmitter ON.
Changing Optional Settings on your H.King ESC
ATTENTION LIPO FLIERS - Always follow your
battery brand's safety recommendations. Your
H.King ESC is set at the factory to use a 3.0 volt
per cell cuto voltage.
Move throttle stick on full throttle (up)
position rst.
Turn on transmitter.
Connect the H.King ESC to a battery
pack.
You should hear the rst multi-tone
ring upon plug in, and the battery
count in beeps if set for Auto-Lipo.
After 2 seconds, you should hear a
second multi-tone ring, indicating
the ESC sees full throttle.
Move throttle stick down to the middle
position, and you will hear another
ring.
Move throttle stick back to the top
position, and you will hear another
ring.
Move throttle stick to the middle
position again.
And you will hear 4 rings all in a row.
Transmitter
ON
Connect
Battery
Battery
count
4
What battery type?
For Lithium Polymer type batteries
(default setting), move the stick up to
full throttle and wait for the rapid beeps
For NiCad and NiMH type batteries,
move the stick to low/o throttle and
wait for the rapid beeps. The rapid
beeps tell you that the controller has now
stored that answer in its memory .
You can now move the stick back to
the middle position for question #2
Brake ON or OFF .
The H.King ESC should start beeping
two repeating beeps. This is setting
question #2.
Brake ON or OFF?
For Brake ON move the stick to full
throttle, and wait for the rapid beeps
For Brake OFF (default setting),
move the stick to low/o throttle, and
wait for the rapid beeps. The rapid
beeps tell you that the controller has
now stored that answer in its memory .
Then the H.King ESC will make a single
beep that repeats. This is setting
question #1.
You can now move the stick back to
the middle position for question #3
Rotation direction.
The H.King ESC will start beeping three
repeating beeps. This is setting
question #3.
Rotation Direction?
For rotation forward (default setting),
move the stick to full throttle, and wait
for the rapid beeps.
5
ATTENTION: From now on speed controller is
armed and any throttle stick moving will make
motor starting!
For rotation reversed , move the
stick to low/off throttle, and wait for
the rapid beeps. The rapid beeps tell
you that the controller has now stored
that answer in its memory .
After the last setting is made, the controller will
exit programming mode, and will arm when the
throttle is in the low position.
SPECIFICATION
H.King Series controllers provide a Linear Battery
Eliminator Circuit (BEC) that will convert the voltage
in your battery pack to the proper voltage for the
operation of your receiver and servos. Please note
that the current supplied by the Linear BEC is
aected by the number of cells in your system.
Higher numbers of cells reduce the amount of
current your Linear BEC can deliver. If you are
using more than ten NiMH/NiCad cells, more than
3 LiPo Cells, or your power consumption is
excessive, you must disable the BEC and use a
separate power source for the receiver. Disable the
BEC by cutting or removing the red wire from the
servo connector on the controller.
6
Model
No.
H.King 10
H.King 20
H.King 35
H.King 50
Max
Amps
Max
Volts
10
20
35
50
3S
LiPo
3S
LiPo
4S
LiPo
4S
LiPo
BEC
Output
5V/1A 23 x 18 x 8 mm
34 x 23 x 12mm
38 x 28 x 16mm
38 x 28 x 16mm
5V/2A
5V/2A
5V/2A
Size
Net
Weight
8g
19g
32g
38g