Introduction Congratulations on choosing the H&A CHASM Studio Monitor Stands. The HEA Studio Monitor Stands are an ideal adjustable height stand to securely support and maintain your treasured audio monitors at the best sweet spot for home or professional studios. The 17-inch-wide triangular base offers stability and security while conserving space requirements of tight setup scenarios. The monitor sits upon an 18 square inch plate with a damping strip to minimize distracting vibrations.
in the Box * 2 Monitor Mounting Plates » 2 Telescoping Columns with Locking Knob and Cotter Pins + 4 Cable Guide Ties + 2 Shaft Mounting Plates » 2 Bases with Rubber Feet = 6 Leveling Spikes + 4 Socket Screws » Allen Wrench Key + HEA Limited 1-Year Warranty
Safety Instructions « Before construction, read all directions carefully. + Retain this manual for future reference. +» Check for product completeness before beginning assembly. « Tighten all socket screws securely before mounting your monitor. » Do not power-tighten any screws, bolts, and nabs. This could damage your stand and strip the threads. + Be careful to safely adjust height; do not pinch your fingers as you raise or lower the column. » The maximum load capacity is 90 lbs.
Features » Rugged metal column and mounting plate supports monitors up to 90 pounds. ~ Sharp design solves tight setup scenarios space requirements into tricky spaces, near walls, behind desks, or in corners. » The 17-inch-wide triangular base offers stability and security. > Handy column locking knobs and a cotter lock pin provide security for the monitors. » Telescoping metal column adjusts quickly with six preset holes to permit the column height raised in 3-inch increments from 36 to 54 inches.
Names of Parts 1 Monitor Mounting Plates 2. Telescoping Column 3. Locking Knob 4. Locking Cotter Pin 5. Base with Rubber Feet 6. Shaft Mounting Plates 7. Socket Screws Bolts 8. Leveling Spikes 9. Cable Guide Ties 10.
Guide te Assembly 2. Line up the monitor mounting plate opening with the Telescoping Column. Place the opening onto the top of the column.
Guide to Assembly 3. The socket screw must be tightened carefully with the Allen Wrench Key [10] 4, Take the Triangular Base [5]1and keep the bottom side up. Slip the longer Socket Screw Bolt [7] through the center opening of the base. 5. Take the Mounting Plate [1] and slip it over the long protruding Socket Screw Bolt [7]. 6. Hold the Mounting Plate [1] firmly in position with one hand as you flip the Base over to mate with the Column’s threaded hole.
Guide to 4 milky 7. Tighten the Socket Screw Bolt [7] carefully with the Allen Wrench [10], taking care to be firm, yet do not over tighten. 8. Make sure all of the assemblies are correctly connected. Take the finished Monitor Stand and flip it over to rest on the Triangular Base [5]. 9. Follow the same steps for the second HEA Studio Monitor Stand.
The Studio Monitor Stands In Use All adjustments must be performed before setting up the Monitor Speakers on the Stands. Height Adjustments 1 Release the Locking Knob [3] 2. Select the height of the Telescopic Column [2]. 3. Place a Locking Cotter Pin [4] through the closest hole to the desired height. 4. The Column [2] safely locks when resting on the Locking Cotter Pin [4]. Tighten the Locking Knob [3] to secure the Stand height.
The Studio Monitor Stands in Use Mount the monitors on the Stands 1 Place the monitor securely on the mounting plate once the Stands are in place. 2. Cable Guide Ties [9] are used to direct and tidy the speaker cables. Place the wires through the guide loops.
The Studio Monitor Stands in Use Level Spikes Stabilization to Stabilize on Carpeting Many floor surfaces are uneven. By using the Leveling Spikes, the Stands gain stability and balance for safety. Take special care to level on carpeted or wom wooden floors. 1. Turn the Stand so that the Base faces up. 2. Unscrew the three Rubber Feet.
The Studio Monitor Stands in Use 3. Replace with three Leveling Spikes [8]. 4, Upright the Stand on the Triangular Base and adjust the Level Spikes according to your surface.
Specifications Minimum Height Maximum Height 54" 137 cm Load Capacity 90 1b.
One Year HEA Limit HBA warrants to the original purchaser that your H&A product shall be free from defects in material and workmanship for the period of one {1} year from the date of purchase (or delivery as may be required in certain jurisdictions), or thirty (30) days after replacement, whichever comes later.
£7 Need Product Support? We are proud of our products and celebrate our customers. We are with you, from product selection to everyday use. Be secure with your purchase and reach us as you need. €, 212-647-9300 ## brands @docudrama 4} Diorama Brands, 42 West 18th Street, New York, NY 10011 You can always contact us at BRANDS @ DOCUDRAMA for personal technical support. Our website contains a wide range of Support and FAQ pages with valuable technical assistance.
