Datasheet

MADE in FRANCE
- EN 60974-1
AUTOPULSE 220-M2
3 interface options for ease of use :
- EASY (simplied module)
- EXPERT (complete module)
- ADVANCED (specic modules)
MIG/MAG
INVERTER
PULSED
10  220 A
Ref. 069855
Brand new Interface which has been simplied and centralized with car-body repairer
operational habits.
Large colour screen for simple control of the welding cycle set up.
2 control knobs and 4 keys for simple and intuitive navigation of the operational menus.
Machine and synergies easily updateable via USB key.
Save up to 500 welding programs for repetitive tasks.
ERGONOMIC INTERFACE
ROBUST AND MOBILE
Reinforced structure.
Frame supporting 2 bottles (2x4m3) with low loading height.
AUTOPULSE 220-M2 is the MIG / MAG pulsed generator with 2 integrated wire feeders ideal for car-
body repairers. Equipped with a digital PFC (Power Factor Correction) the Autopulse supplies pulsed
welding quality comparable to three-phase products. Designed for highest performance the 220-
M2 features several synergic curves which enables exceptional arc quality. The Autopulse 220-
M2 is incredibly versitile, 2 welding torches for use with multiple material including Steel and
Aluminium increase productivity for the modern day workshop. The intuitive interface and high
precision wire feed are ideal for car-body applications with exceptional welding quality even
when used with thin sheet materials.
www.gys.fr
MAXIMUM PRODUCTIVITY
4 microprocessors to give four times the processing power.
2 wheel drive system with 2 active drive rolls.
Up to 2 wire reels of Ø 300 mm accepted.
Automatic torch detection while pulling the trigger.
Balancing arm with torch support (x3) and welding helmet.
Push pull torch compatibilty (24V).
SIMPLIFIED WELDING
68 (Adjustable) synergic curves ensure an outstanding weld for a large range of
materials, wire sizes and gas.
The fully synergic mode calculates the optimal welding parameters automatically, this can be
also be adjusted (wire speed, voltage and current).
OPTIMISED MIG/MAG SETTINGS
Welding processes : Standard, Pulse, Pulse in Pulse, Cold pulse and Manual.
Trigger modes : 2T, 4T, SPOT, DELAY and TACK function.
Precise control over the welding cycle : CreepSpeed, Softstart, Hotstart, Upslope,
Downslope, Crater Fill, Post gas, etc.
2 specic compartments to isolate and avoid pollution of the aluminum coil:
- aluminum wire Ø 0.8 / 1.0 / 1.2 (lower compartment n ° 1)
- steel wire Ø 0.6 / 0.8 / 1.0 mm (upper compartment n ° 2)
- stainless steel wire Ø 0.8 / 1.0 mm (upper compartment n ° 2)
- CuSi and CuAl wire Ø 0.8 / 1.0 mm (upper compartment n ° 2)
 
équipé d’origine /
original equipement
/ originalausstatung
/ equipamiento de
fabrica
EN
60974-1 (40°C)
U
0
 
IP
 
Protected
& compatible
power generator
(+/-15 %)
50/60 Hz A min  max
ø mm ø mm
Electronic
Control
m/min
X (40°C) V cm kg
200 >240 V
1~
16 10  220 0.6  1.2
200
300
50 W
0.5  20
0.8/1.0
1.0/1.2 (Alu)
150 A @ 60%
130 A @ 100%
80 88 x 93 x 63 63 IP 21 10 kVA
ACCESSORIES (OPTIONS)
Push Pull Torch (24 V)
046283 4 m 3 kg
220 A
(20%)
0.8  1.2
Supplied with 2 torches :
Steel 150 A
3 m - Ø 0.8
Alu 250 A
3 m - Ø 1.2
+ Earth clamp - 35 mm² - 4 m
+ Balancing arm
PFC
265 V185 V
230 V110 V
n°1
n°2