Datasheet

MADE in FRANCE
- EN 60974-1
NEOPULSE 320 C
PULSED MIG/MAG
WELDING MACINE
10 - 320 A
P.N. 062474
MIG/MAG:
- steel wire: Ø 0.6 - 1.2 mm
- stainless steel wire: Ø 0.8 - 1.2 mm
- aluminium wire: Ø 0.8 - 1.2 mm
- CuSi and CuAl wire: Ø 0.8 - 1.2 mm
PULSED / DC MMA: basic, rutile and cellulosic electrodes (up to Ø 5 mm)
PULSED / DC LIFT TIG
Supplies without
accessories
MULTI-PROCESS WELDING
ROBUST AND MOBILE
Reinforced metal casing and non slip rubber pads.
IP23-rated casing.
Separate, optional NEOFEED-4W* dispenser with air- or water-connection cables (up to 20 m).
Remotely adjustment of the machine’s settings using two, optional remote controls (*digital or analogue).
The NEOPULSE 320 C is a digital, three-phase, pulsed, MIG/MAG welding machine. Designed to operate at the highest
performance level using the latest technology, it features various synergy curves as well as exceptional arc quality and
performance. User friendly and highly practical, its digital interface is designed to allow the welding settings to be quickly
and easily adjusted. Equipped with a precise, four-reel, wire-feeding system, this power source provides unparalleled
productivity and welding quality on all types of materials.
www.gys.fr
MAXIMUM PRODUCTIVITY
Intended for heavy and demanding industrial applications:
Four microprocessors increase the communication speed and optimise the machine’s eciency.
High productivity thanks to its high duty cycle (300 A @ 60%).
Compatible wire-feed reels: Ø 200 / 300 mm.
Can be connected to a SAM control interface for automated or robotic applications (optional).
Robust design to withstand shocks and vibrations.
Powerful, motorised wire-feed system (100 W) with four active drive rolls.
Very high arc voltage for easier ignition and exceptional arc dynamics.
SMART
SYNERGY mode: after selecting the material/gas combination and the wire diameter the
NEOPULSE 320 C will automatically work out the optimal welding settings whilst still allowing you
to adjust the settings (wire-feed speed, voltage, current and arc length).
EASY TO USE
New user friendly interface focused on the welders’ navigation habits.
Machine and synergy updates using a USB key.
Optional cooling unit (P.N. 013537) and trolley (P.N. 037328).
Stores up to 500 welding programs (can be saved to a USB key).
Displays the current/voltage during and after the welding process (WPS/PQR).
Choose which key parameter setting to display on the screen (wire-feed speed, average welding
current, etc.).
Internal lighting system for the wire-feed motor and reel.
Viewing window on wire-compartment’s door for easily wire monitoring.
Smart ventilation management system to reduce power consumption, dust intake and noise.
Compatible with Push-Pull torch (24 V / 42 V).
OPTIMISED MIG/MAG SETTINGS
Welding processes: Manual, Standard Dynamic, Pulsed, Arc Module (a variation of hot / cold current).
TACK modes: SPOT and DELAY.
Trigger options: 2T and 4T.
Precise control of the entire welding cycle: CreepSpeed, Softstart, Hotstart, Upslope, Downslope, Crater Fill and Post-Gas, etc.
PRECISE
Calibrate the welding cables and motor speed to adjust the displayed voltage and rene the energy calculation.
Energy consumption, displays and calculates the energy consumption after welding in accordance with standards EN1011-1, ISO / TR 18491 and QW-
409.
Portable: load / save user JOBS and machine settings using a USB key.
Traceability: track / record all welding stages, weld by weld, during industrial manufacturing in accordance with standard EN ISO 3834.
Three user-interface levels:
- Easy: simplied features
- Expert: full display
- Advanced: full access to all parameters
* Digital connector kit required (P.N. 063938)