Fire pit table Instruction manual For any missing or damaging parts, hardware, or any other problems, WELCOME to email us at: SERVICE@RILYSON.
INSTALLER: Leave this manual with the appliance. CONSUMER: Retain this manual for future reference. WARNING: It is UNSAFE to use this product for cooking! WARNING: For Outdoor Use Only. Installation and service must be performed by a qualified installer, service agency, or the gas supplier. WARNING Do not store or use gasoline, or other flammable vapors and liquids in the vicinity of this or any other appliance.
IMPORTANT SAFETY INFORMATION 1. The installation must conform with local codes or in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1● NFPA 54; National Fuel Gas Code; Natural Gas and Propane Installation Code, CSA B149.1; or Propane Storage and Handling Code, CSA B149.2, as applicable. 2.
IMPORTANT SAFETY INFORMATION ABOUT PROPANE (LP) GAS 1. The LP-gas supply cylinder to be used must be constructed and marked in accordance with the U.S. Deparment of Transportation (D.O.T.) Specifications for LP-Gas Cylinders, or the Standard for Cylinders, Spheres and Tubes for Transportation of Dangerous Goods and Commission, CAN/CSA-B339, as applicable. 2. The LP-gas supply cylinder to be used must have a listed overfilling prevention device (See Figure 1). 3.
PART LIST CODE IMAGE PARTS QTY CODE A SIDE PANEL A 1 B SIDE PANEL B C PARTS QTY G LID 1 1 H WASHERS 14 SIDE PANEL 1 I M6*15 2 D SIDE PANEL WITH DOOR 1 J M6*20 4 E CYLINDER HOLDER 1 K M6*30 8 F TABLE TOP 1 L HEX KEY 1 M VOLCANIC STONE 1 G IMAGE F B M A C D Figure 2 E 05
STEP 1: Remove the part from carton to a safe place. Caution: Burner fixed on ( F ) ; Do not break the burner. Caution: Do not remove the label on the pilot box until volcanic stone is insert. WARNING: keep children away during assembly, as this item contains fire glass, which are small pieces and can be swallowed by children.
STEP 3: Attach the cylinder holder(E) to side panel by 4 pcs bolts(K) and 4 washers(H) with Hex key (L) Don’t fully tighten bolts.
STEP 4: Attach the side panel D to the side panel (A) (B) by 2 bolts (I) and 4 washer (H) with Hex key (L). Don’t fully tighten bolts.
STEP 5: Keep the table top upside down as Figure 7. Attach the table top (F) to side panels by 4 bolts (J) and washers (H) by Hex key (L).
STEP 6: Turn over the table. put the volcanic stone (M) around the buner. G M Figure 8 STEP 7: Place the gas cylinder into the cylinder holder (figure 9), secure the cylinder by tightening clockwise the bolt (figure 10) found on the cylinder holder, so the cylinder cannot move from side to side or fall down. The knob on the control panel is tunred all the way to the "OFF" position (figure 11) when the fire pit is not in use.
BATTERY Make sure the control knob is in the “OFF” position. Unscrew the push button cap on the ignitor module located on the control panel to access the battery compartment. The ignitor module requires one +AAA size battery. BATTERY IS NOT INCLUDED. (See Figure 12). WARNING: 1. Please observe proper polarity and use the correct battery type when placing or replacing the battery. Improper installation could result in ignition failure. 2.
To perform a leak test: 1. Make 2~3 oz. of leak solution by mixing one part liquid dishwashing detergent and three parts water. Noted: make sure control knob is “OFF”. 2. Apply several drops of solution where the cylinder attaches to regulator (See Figure 13), inspect the solution at the connection looking for bubbles. If NO bubbles appear, the connection is secure. If bubbles appear, the connection has the leak, disconnect the regulator, reconnect, perform another leak check.
Observe Flame Height When Lit: The burner will display blue and yellow flames. These flames should be a blue / yellow color between 1~2 in. height (See below). These flames should not be yellow or produce thick smoke. This would indicate an obstruction of airflow through the burners. The flames should be blue with straight yellow tops.
For any missing or damaging parts, hardware,or any other problems, WELCOME to email us at: SERVICE@RILYSON.COM Or 1-888-733-8169 Toll free Monday-Friday 9AM - 5PM EST * Don't fully tighten all the bolts till the very end! PRE-ASSEMBLY PREPARATION: --- Please read through the instructions before beginning assembly. --- Clear out the space for assembly and lay out all of the parts based on the Parts List, extra room will allow you to easily determine if all the pieces are present.
STEP 1 B DE C DE Attach side panel and feet with D,E.
STEP 3 C DE DE DE DE Attach side panel and feet with D,E.
STEP 5 A E D C Attach top panel and ottoman frame with D,E. Tighten all the bolts! STEP 6 Put seat cushion on the ottoman.
ASSEMBLY INSTRUCTION For any missing or damaging parts, hardware,or any other problems, WELCOME to email us at: SERVICE@RILYSON.COM Or 1-888-733-8169 Toll free Monday-Friday 9AM - 5PM EST * Don't fully tighten all the bolts till the very end! PRE-ASSEMBLY PREPARATION: --- Please read through the instructions before beginning assembly. --- Clear out the space for assembly and lay out all of the parts based on the Parts List, extra room will allow you to easily determine if all the pieces are present.
A1 Left Arm 1 A2 B Feet 2 D Seat F Bolt H Bolt Right Arm 1 C Back 1 1 E Bolt 8 6 G M6 * 35MM 2 M6 * 95MM J L Back Cushion Wrench 3 1 Bolt 4 I Washer 20 K Seat Cushion 3 M6 * 20MM M6 * 40 MM
STEP 1 I E 6*20mm Attach left arm and feet with E and I.Don't tighten bolts! Attach right arm and feet in the same way. STEP 2 C I G 6*40mm D Attach seat and back with G and I.
STEP 3 I C D 6*95mm A1 F I 6*35mm Attach left arm and back with H and I.Don't tighten bolts! Attach left arm and back with F and I.Don't tighten bolts! Attach left arm and seat with F and I.Don't tighten bolts! Attach right arm in the same way.Tighten all the bolts! STEP 4 Put seat and back cushions on the sofa.
ASSEMBLY INSTRUCTION For any missing or damaging parts, hardware,or any other problems, WELCOME to email us at: SERVICE@RILYSON.COM Or 1-888-733-8169 Toll free Monday-Friday 9AM - 5PM EST * Don't fully tighten all the bolts till the very end! PRE-ASSEMBLY PREPARATION: --- Please read through the instructions before beginning assembly. --- Clear out the space for assembly and lay out all of the parts based on the Parts List, extra room will allow you to easily determine if all the pieces are present.
Left Arm 1 A2 B Feet 2 D Seat F Bolt H Bolt A1 Right Arm 1 C Back 1 1 E Bolt 8 6 G M6 * 35MM 2 M6 * 95MM J L Back Cushion Wrench 1 1 Bolt 2 I Washer 18 K Seat cushion 1 M6 * 20MM M6 * 40 MM
STEP 1 A1 I 6*20mm E B Attach left arm and feet with E and I.Don't tighten bolts! Attach right arm and feet in the same way. STEP 2 C I G 6*40mm I G D Attach seat and back with G and I.
STEP 3 I C D H 6*95mm A1 F I 6*35mm Attach left arm and back with H and I.Don't tighten bolts! Attach left arm, back and seat with Fand I.Don't tighten bolts! Attach right arm in the same way.Tighten all the bolts! STEP 4 Put seat and back cushions on the chair.
ASSEMBLY INSTRUCTION For any missing or damaging parts, hardware,or any other problems, WELCOME to email us at: SERVICE@RILYSON.COM Or 1-888-733-8169 Toll free Monday-Friday 9AM - 5PM EST * Don't fully tighten all the bolts till the very end! PRE-ASSEMBLY PREPARATION: --- Please read through the instructions before beginning assembly. --- Clear out the space for assembly and lay out all of the parts based on the Parts List, extra room will allow you to easily determine if all the pieces are present.
A 1 B 2 C 1 D 8 E 8 F 1 M6 * 20 MM STEP 1 B B STEP 2 A C
