Datasheet

Setting Resolution
Accuracy
*2
200 V
100 V
200 V
Resolution
Accuracy
*2
Resolution
Accuracy
Resolution
Accuracy
*3
Resolution
Accuracy
*4
Resolution
Accuracy
*5
100 V
Setting Resolution
Accuracy
Stability
*5
DC OFFSET*
6
Accuracy
*2
200 V
200 V
-250 V to +250 V / -500 V to +500 V
±0.2% or less
0.15% @45 - 65Hz; 0.5% @DC, all other frequencies (0 to 100%, via output terminal)
0.7 Vrms / 1.4 Vrms (TYP)
0.5 % or less
100 us (TYP)
70 % or more
0.1 V
For 45 Hz to 65 Hz and DC: ±(0.5 % of reading + 0.3 V/0.6 V)For 40 Hz to 999.9 Hz: ±(0.7 % of reading + 0.9 V/1.8 V)
0.1 V
For 45 Hz to 65 Hz and DC: ±(|2 % of reading| + 1 V / 2 V)
0.01 A 0.01 A
For 45 Hz to 65 Hz and DC:±(0.5 % of reading+0.02 A/0.02 A); For 45 Hz to 65 Hz and DC:±(0.5 % of reading+0.04 A/0.02 A);
For 40 Hz to 999.9 Hz:±(0.7 % of reading + 0.04 A / 0.04 A) For 40 Hz to 999.9 Hz:±(0.7 % of reading + 0.08 A / 0.04 A)
0.1 A 0.1 A
For 45 Hz to 65 Hz and DC:±(|2 % of reading|+0.2 A/0.1 A) For 45 Hz to 65 Hz and DC:±(|2 % of reading|+0.2 A/0.1 A)
0.1 / 1 W 0.1 / 1 W
±(2 % of reading + 0.5 W)
Resolution
Accuracy
*5*6
Resolution
Accuracy
*5*7
Range
Resolution
Range
Resolution
±(2 % of reading + 1 W)
0.1 / 1 VA 0.1 / 1 VA
±(2 % of reading + 0.5 VA) ±(2 % of reading + 1 VA)
0.1 / 1 VAR 0.1 / 1 VAR
±(2 % of reading + 0.5 VAR) ±(2 % of reading + 1 VAR)
0.000 to 1.000 0.000 to 1.000
0.001 0.001
0.00 to 50.00 0.00 to 50.00
0.01 0.01
0.1 V
±(|0.5 % of set| + 0.6 V / 1.2 V)
5 A
2.5 A
20 A
10 A
500 W
10 A
5 A
40 A
20 A
1000 W
100Vac
200Vac
100Vac
200Vac
Setting Resolution
100 Vac to 240 Vac
90 Vac to 264 Vac
Single phase, Two-wire
47 Hz to 63 Hz
0 VA or less80
0.95 (typ.)
0.90 (typ.)
A8
4A
100 Vac to 240 Vac
90 Vac to 264 Vac
Single phase, Two-wire
47 Hz to 63 Hz
1500 VA or less
0.95 (typ.)
0.90 (typ.)
15 A
7.5 A
NORMINAL INPUT VOLTAGE
INPUT VOLTAGE RANGE
PHASE
INPUT FREQUENCY RANGE
MAX. POWER CONSUMPTION
POWER FACTOR
*1
MAX. INPUT CURRENT
INPUT RATING (AC)
AC MODE OUTPUT RATINGS (AC rms)
OUTPUT RATING FOR DC MODE
OUTPUT VOLTAGE STABILITY
OUTPUT VOLTAGE WAVEFORM DISTORTION RATIO, OUTPUT VOLTAGE RESPONSE TIME, EFFICIENCY
MEASURED VALUE DISPLAY
*1 For an output voltage of 100 V/200 V (100V/200V range), maximum current, and a load power factor of 1..
0.0 V to 175.0 V / 0.0 V to 350.0 V
0.1 V
±(0.5 % of set + 0.6 V / 1.2 V)
Single phase, Two-wire
5 A
2.5 A
20 A
10 A
500 VA
AC Mode: 40.00 Hz to 999.9 Hz, AC+DC Mode: 1.00 Hz to 999.9 Hz
0.01 Hz (1.00 to 99.99 Hz), 0.1 Hz (100.0 to 999.9 Hz)
For 45 Hz to 65 Hz: 0.01% of set, For 40 Hz to 999.9 Hz: 0.02% of set
± 0.005%
0.0° to 359.9° variable (setting resolution 0.1°)
Within ± 20 mV (TYP)
*1. 100 V / 200 V range
*2. For an output voltage of 17.5 V to 175 V / 35 V to 350 V, sine wave, an output frequency of 45 Hz to 65 Hz, no load, DC voltage setting 0V (AC+DC mode) and 23°C ± 5°C
*3. For an output voltage of 1 V to 100 V / 2 V to 200 V, Limited by the power capacity when the output voltage is 100 V to 175 V / 200 V to 350 V.
*4. With respect to the capacitor-input rectifying load. Limited by the maximum current.
*5. For 45 Hz to 65 Hz, the rated output voltage, no load and the resistance load for the maximum current, and the operating temperature.
*6. In the case of the AC mode and output voltage setting to 0 V.
*1. 100 V / 200 V range
*2. For an output voltage of -250 V to -25 V, +25 V to +250 V / -500 V to -50 V, +50 V to +500 V, no load, AC volatge setting 0V (AC+DC mode) and 23 ± 5℃℃
*3. For an output voltage of 1.4 V to 100 V / 2.8 V to 200 V, Limited by the power capacity when the output voltage is 100 V to 250 V / 200 V to 500 V.
*4. Within 5 ms, Limited by the maximum current.
*1. Power source input voltage is 100 V, 120 V, or 230 V, no load, rated output.
*2. For an output voltage of 75 V to 175V/150V to 350V, a load power factor of 1, stepwise change from an output current of 0 A to maximum current(or its reverse), using the output terminal on the rear panel.
*3. For 5 Hz to 1 MHz components in DC mode using the output terminal on the rear panel.
*1. At an output voltage of 50 V to 175 V / 100 V to 350 V, a load power factor of 1, and in AC and AC+DC mode.
*2. For an output voltage of 100 V / 200 V, a load power factor of 1, with respect to stepwise change from an output current of 0 A to the maximum current (or its reverse); 10% ~ 90% of output voltage
*3. For AC mode, at an output voltage of 100 V / 200 V, maximum current, and load power factor of 1 and sine wave only.
VOLTAGE
Setting Range
*1
OUTPUT PHASE
OUTPUT ON PHASE
MAXIMUM CURRENT
*3
100 V
Setting Range
MAXIMUM PEAK CURRENT
*4
100 V
FREQUENCY
POWER CAPACITY
10 A
5 A
40 A
20 A
1000 VA
VOLTAGE
LINE REGULATION
*1
LOAD REGULATION
*2
RIPPLE NOISE
*3
OUTPUT VOLTAGE WAVEFORM DISTORTION RATIO
*1
OUTPUT VOLTAGE RESPONSE TIME
*2
EFFICIENCY
*3
VOLTAGE
CURRENT
POWER
LOAD POWER FACTOR
LOAD CREST FACTOR
RMS, AVG Value
*1
PEAK Value
RMS, AVG Value
PEAK Value
Active (W)
Apparent (VA)
Reactive (VAR)
MAXIMUM CURRENT
*3
MAXIMUM PEAK CURRENT
*4
POWER CAPACITY
Setting Range
*1
SPECIFICATIONS
ASR-2100/ASR-2100RASR 2050/ASR-2050R-