Instructions / Assembly

ManualsBrandsGutter Guard by Gutterglove ManualsBuilding materials4 ft. Stainless Steel 6 in. Micro-Mesh Gutter Guard (3-Pack)

Tin snips:

There are

many

brands,

styles and

designs

that will

work.

Drill: For self-tapping

screws. Not needed if

you use the 3M VHB

tape provided for

installing gutter guard.

INSTALL & USERS GUIDE

Contact informaon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Tools you may need . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

STEP 1: Choose your guer and roof conguraon . . . . . . . . . . . . . . . . . . . . 2

STEP 2: The basics in every installaon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

STEP 3: Two very important installaon rules . . . . . . . . . . . . . . . . . . . . . . . . 8

How to bend the mesh . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

How to take care of your new guer guard . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

How to extend your warranty from 10 years to 25 years . . . . . . . . . . . . . . . . . 12

CONTACT INFORMATION

Company Gutterglove, Inc.

P.O. Box 3307

Rocklin, California 95677

Tech Support Phone: (866)892-8442

Monday through Friday

8am to 5pm PST

Email: Info@GutterGuard.com

Install info: www.GutterGuard.com/howtoinstall

FAQ: www.GutterGuard.com/faq

TOOLS YOU MAY NEED

Thanks so much for choosing my gutter guard! I designed it to fit your gutter, no matter

what type of gutter and roof configuration you have. GUARANTEED! So don’t return it

if you think it won’t fit. It will fit and I’ll show you how. Make sure to register online at

www.GutterGuard.com to extend your warranty from 10 years to 25 years!

Ladder & ladder standoff: A ladder standoff is an attachment that

connects to a standard extension ladder that pushes your ladder away from

the gutter so you can perform the install comfortably without the ladder

resting on the gutter. The standoff in the photo is made by “Ladder-Max”.

Summary of content (12 pages)

PAGE 1
Thanks so much for choosing my gutter guard! I designed it to fit your gutter, no matter what type of gutter and roof configuration you have. GUARANTEED! So don’t return it if you think it won’t fit. It will fit and I’ll show you how. Make sure to register online at www.GutterGuard.com to extend your warranty from 10 years to 25 years! INSTALL & USERS GUIDE Contact information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Tools you may need . . . . . . . . .
PAGE 2
STEP 1: Choose your gutter and roof configuration Select the diagram below that best resembles your gutter and roof scenario. This will determine whether you slide the gutter guard under the roof shingles, or bend the back of the mesh up or down and fasten to the back of the gutter or fascia. Once you’ve selected a diagram, continue to Step 2. The diagrams all refer to a roof shingle and gutter, they imply ALL shingle and gutter types.
PAGE 3
STEP 1: …. continued …. o Ro le ing h s f Flat roof r Gutte Guard OPTION 1: Bend mesh up Screw for holding up gutter guard. Fascia wood d uar rG e tt Gu OPTION 2: Gutter Bend mesh down Fascia wood DIAGRAM E Gutter Use screws to hold up gutter guard. Sometimes the gutter guard isn’t long enough to go under the shingles. You can put 3 screws in the back gutter or fascia wood for holding up each section of the gutter guard. DIAGRAM D Flat roof.
PAGE 4
STEP 2: The basics in every installation Clean out your gutters: Take the time to clean the leaves, pine needles and other debris from your gutters and downspouts first. Go to ConsumerReports.org and read the article “10 Questions For Robert Lenney, Gutter Expert” on how to clean your gutters out properly and safely.
PAGE 5
Step 2.1 Step 2.2 Clean: Wipe off top of gutter so it’s very clean by using a mixture of rubbing alcohol and water. Wipe off all residues. Straight Sections: Peel off a few inches of the red strip. Slide section under roof shingle. Pull red strip off. Push down firmly by sliding finger along top. Step 2.3 Joining sections A B Mesh extends slightly past the ends of each section. Line the ends up and the mesh will overlap each other. Just set the mesh ends on top of each other (A).
PAGE 6
Step 2.4 Cover end of gutter C D Cut the front and rear aluminum extrusions back with any brand of tin snips so the mesh is free to tuck inside the gutter and cover the opening. SPECIAL NOTE: The rear aluminum extrusion (C) is shorter in length than the front extrusion (D). This is so the extrusions don’t lay on top of each other in the back, causing the shingles to lift. Slide excess mesh down and inside gutter. This caps off the end to keep debris, birds, rodents and insects out. Step 2.
PAGE 7
Step 2.6 Outside corner of gutter Push rear aluminum strip down in gutter. Mark adjacent section and trim off. Step 2.7 Cutting sections F The aluminum extrusions can be tough to cut, so it’s ok to notch them (F), then you can snap them in two with your hands. The tin snips will cut through the mesh easily. Removing gutter guard “Check out the How-to-Install tab at my website for more gutter and roof install techniques like shown below.
PAGE 8
STEP 3: Two very important installation rules Follow these two rules so rainwater flows smoothly into your gutter and not over the front edge of your gutter. RULE #1 Remove gap: Make sure the front lip of the gutter guard is flat against the front lip of your gutter to remove any gap.
PAGE 9
How to bend the mesh Bending the back of the mesh allows the gutter guard to be installed on all gutter and roof configurations. All you need are two 1” x 2” boards 4.5’ long and a couple 4” clamps. When choosing a board, get a board that has square edges instead of rounded edges. A square edged board will put straight creases in the mesh when you bend it. Bend the mesh up or down depending on your application. Tech Support (866)892-8442 Info@GutterGuard.
PAGE 10
How to bend the mesh …. continued …. Below are several examples of where bending the mesh allows the gutter guard to be installed on any gutter and roof configuration. Tech Support (866)892-8442 Info@GutterGuard.
PAGE 11
How to take care of your new gutter guard By Robert Lenney Before I share some tips on how to get decades of high quality performance out of my gutter guard, I want to dispel a huge myth. MYTH: Gutter guards are maintenance-free and self-cleaning. FACT: All gutter guards require some form of maintenance. I’ve seen a couple manufacturers over the years promote their gutter guards as maintenance-free or self-cleaning, DON’T BELIEVE IT.
PAGE 12
Extend War r anty by 15 year s! Register ONLINE AT www.GutterGuard.com 10 Year Limited Parts Warranty Gutterglove, Incorporated (herein referred to as GGI) warrants to the original purchaser that its specially designed Gutter Guard will be free from defects in manufactured parts, and agrees that it will, at its option only, either repair the defect or replace the defective part thereof with a new or reconditioned equivalent.