SDS

6. Accidental release measures
Keep unnecessary personnel away. Keep people away from and upwind of spill/leak. Remove all
possible sources of ignition in the surrounding area. Keep out of low areas. Many gases are
heavier than air and will spread along ground and collect in low or confined areas (sewers,
basements, tanks). Wear appropriate protective equipment and clothing during clean-up. Avoid
breathing mist/vapor. Emergency personnel need self-contained breathing equipment. Do not
touch damaged containers or spilled material unless wearing appropriate protective clothing.
Ventilate closed spaces before entering them. Use appropriate containment to avoid
environmental contamination. Transfer by mechanical means such as vacuum truck to a salvage
tank or other suitable container for recovery or safe disposal. Local authorities should be advised if
significant spillages cannot be contained. For personal protection, see section 8 of the SDS.
Personal precautions,
protective equipment and
emergency procedures
Refer to attached safety data sheets and/or instructions for use. Stop leak if you can do so without
risk. Move the cylinder to a safe and open area if the leak is irreparable. Isolate area until gas has
dispersed. Eliminate all ignition sources (no smoking, flares, sparks, or flames in immediate area).
Keep combustibles (wood, paper, oil, etc.) away from spilled material. Prevent entry into
waterways, sewer, basements or confined areas. Absorb in vermiculite, dry sand or earth and
place into containers. Following product recovery, flush area with water.
Small Spills: Wipe up with absorbent material (e.g. cloth, fleece). Clean surface thoroughly to
remove residual contamination. For waste disposal, see section 13 of the SDS.
Methods and materials for
containment and cleaning up
Avoid release to the environment. Inform appropriate managerial or supervisory personnel of all
environmental releases. Prevent further leakage or spillage if safe to do so. Avoid discharge into
drains, water courses or onto the ground. Use appropriate containment to avoid environmental
contamination.
Environmental precautions
7. Handling and storage
Minimize fire risks from flammable and combustible materials (including combustible dust and
static accumulating liquids) or dangerous reactions with incompatible materials. Handling
operations that can promote accumulation of static charges include but are not limited to: mixing,
filtering, pumping at high flow rates, splash filling, creating mists or sprays, tank and container
filling, tank cleaning, sampling, gauging, switch loading, vacuum truck operations. Pressurized
container: Do not pierce or burn, even after use. Do not use if spray button is missing or defective.
Do not spray on a naked flame or any other incandescent material. Do not smoke while using or
until sprayed surface is thoroughly dry. Do not cut, weld, solder, drill, grind, or expose containers to
heat, flame, sparks, or other sources of ignition. All equipment used when handling the product
must be grounded. Close valve after each use and when empty. Protect containers from physical
damage; do not drag, roll, slide, or drop. When moving containers, even for short distances, use a
cart (trolley, hand truck, etc.) designed to transport containers. Suck back of water into the
container must be prevented. Do not allow backfeed into the container. Purge air from system
before introducing gas. Use only properly specified equipment which is suitable for this product, its
supply pressure and temperature. Contact your gas supplier if in doubt. Do not re-use empty
containers. Avoid contact with eyes. Avoid prolonged exposure. Use only in well-ventilated areas.
Wear appropriate personal protective equipment. Avoid release to the environment. Observe good
industrial hygiene practices.
For additional information on equipment bonding and grounding, refer to the Canadian Electrical
Code in Canada, (CSA C22.1), or the American Petroleum Institute (API) Recommended Practice
2003, "Protection Against Ignitions Arising out of Static, Lightning, and Stray Currents" or National
Fire Protection Association (NFPA) 77, "Recommended Practice on Static Electricity" or National
Fire Protection Association (NFPA) 70, "National Electrical Code".
Precautions for safe handling
Level 2 Aerosol.
Store locked up. Pressurized container. Protect from sunlight and do not expose to temperatures
exceeding 50°C/122 °F. Do not puncture, incinerate or crush. Do not handle or store near an open
flame, heat or other sources of ignition. This material can accumulate static charge which may
cause spark and become an ignition source. Avoid spark promoters. Ground/bond container and
equipment. These alone may be insufficient to remove static electricity. Store in tightly closed
container. Store in a well-ventilated place. Stored containers should be periodically checked for
general condition and leakage. Store away from incompatible materials (see Section 10 of the
SDS).
Conditions for safe storage,
including any incompatibilities
8. Exposure controls/personal protection
Occupational exposure limits
The following constituents are the only constituents of the product which have a PEL, TLV or other recommended exposure limit.
At this time, the other constituents have no known exposure limits.
3 / 10
SDS
US
Material name: Gunk Brake Parts Cleaner - Non Chlorinated
M710 Version #: 01 Revision date: 02-21-2023 Issue date: 02-21-2023