GUILD 135W Detail Sander PPS135G Instruction Manual After Sales Support UK/Ireland 0333 3201989 Help@guildpowertools.co.uk Important - Please read these instructions fully before operating or maintaining your Guild Detail Sander These instructions contain important information that will help you get the best from your Guild Detail Sander, ensuring it remains safe to operate.
Contents Safety Information.....................................................................................................3 In The Box..................................................................................................................6 Accessories................................................................................................................6 Operating Instructions...............................................................................................
Safety Information Important - Please read these instructions fully before starting assembly Warning Symbols The following warning symbols appear throughout this assembly manual and indicate the appropriate safety measures you should take when assembling and operating the Detail Sander. To reduce the risk of injury, Please read the instruction manual Warning Wear ear protection Wear eye protection Wear dust mask Double insulation Waste electrical products must not be disposed of with household waste.
Safety Information Important - Please read these instructions fully before starting assembly General Power Tool Safety Warnings WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.
Safety Information Important - Please read these instructions fully before starting assembly General Power Tool Safety Warnings d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. f) Dress properly. Do not wear loose clothing or jewellery.
In The Box Parts 1 Handle 2 On/off switch 3 Sanding pad 4 Sanding paper 5 Dust outlet 6 Dust collection Box 2 1 3 4 5 6 Accessories Dust box Sanding paper (2x80 grit & 2x100 grit) 6 Customer Helpline 0333 3201989 1pc 4pcs
Operating Instructions NOTE: Before using the tool, read the instruction book carefully. Intended Use The machine is intended for dry sanding of wood, plastic, filler and coated surfaces. 1. FITTING THE SANDING PAPER (SEE FIG A) FIT THE SANDING PAPER This sander features an easy hook and loop accessory fastening system for quick changing without clamps. The sanding papers are placed directly onto the base plate. The hole pattern in the base plate and sanding paper must match.
Operating Instructions flow through the box better. To empty the dust box, pull off the dust box out of the dust extraction outlet directly and shake out dust. 3.USING THE DUST OUTLET (SEE FIG C) Your sander is equipped with a 35mm dust outlet, which are designed for connecting the hose of a vacuum cleaner. If the vacuum hose is 35mm, insert the hose directly into the rear dust outlet of sander. First please turn on the vacuum cleaner, and then turn on the sander.
Operating Instructions to corners and edges of moulding. 7. ORBITAL SANDING Your sander operates in small circular rotations which allows efficient material removal. Operate your sander in long sweeping movements across your workpiece and even across the grain. For a finer finish, always use a fine grain sandpaper and only move the sander in the direction of the grain and never across the grain.
Maintenance Remove the plug from the socket before carrying out any adjustment, servicing or maintenance. Your power tool requires no additional lubrication or maintenance. There are no user serviceable parts in your power tool. Never use water or chemical cleaners to clean your power tool. Wipe clean with a dry cloth. Always store your power tool in a dry place. Keep the motor ventilation slots clean. Keep all working controls free of dust.
Technical Data Technical Data Table Voltage 230-240V~50Hz Power input 135W No load speed 12000 /min Base size 140x140x80mm Orbital dia 1.0 mm Protection class /II Machine weight 1.14 Kg Noise Information A weighted sound pressure A weighted sound power LpA : 81.8dB(A) LwA : 92.8dB(A) KpA & KwA=3.0dB(A) Wear ear protection Vibration Information Vibration total values (triax vector sum) determined according to EN 60745: Typical weighted vibration Vibration emission value ah = 9.
Technical Data Vibration Information Helping to minimize your vibration exposure risk. ALWAYS use sharp chisels, drills and blades Maintain this tool in accordance with these instructions and keep well lubricated (where appropriate) If the tool is to be used regularly then invest in anti vibration accessories. Avoid using tools in temperatures of 100C or less Plan your work schedule to spread any high vibration tool use across a number of days.
Guarantee This product is selected for DOMESTIC USE ONLY and not for business use. This product is guaranteed against manufacturing defects for a period of 24 months. This does not cover the product where the fault is due to misuse, abuse, use in contravention of the instructions, or where the product has been the subject of unauthorised modifications or alterations, or has been the subject of commercial use.
Plug Replacement (Uk & Ireland Only) If you need to replace the fitted plug then follow the instructions below. IMPORTANT The wires in the mains lead are colored in accordance with the following code: Blue – Neutral Brown – Live As the colors of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows. The wire which is coloured blue must be connected to the terminal which is marked with N.
