GUILD 1200W Compound Mitre Saw BMS210G Instruction Manual After Sales Support UK/Ireland 0333 3201989 Help@guildpowertools.co.uk Important - Please read these instructions fully before operating or maintaining your Guild compound mitre saw These instructions contain important information that will help you get the best from your guild compound mitre saw, ensuring it remains safe to operate.
Contents Safety Information.....................................................................................................3 In The Box..................................................................................................................7 Accessories................................................................................................................7 Assembly Instructions...............................................................................................
Safety Information Important - Please read these instructions fully before starting assembly Warning Symbols The following warning symbols appear throughout this assembly manual and indicate the appropriate safety measures you should take when assembling and operating the compound mitre saw.
Safety Information Important - Please read these instructions fully before starting assembly General Power Tool Safety Warnings WARNING: When using electric tools basic safety precautions should always be followed to reduce the risk of fire, electric shock and personal injury including the following. Read all these instructions before attempting to operate this product and save these instructions. Safe operation 1 - Keep work area clear - Cluttered areas and benches invite injuries.
Safety Information Important - Please read these instructions fully before starting assembly General Power Tool Safety Warnings 13 - Do not overreach - Keep proper footing and balance at all times. 14 - Maintain tools with care - Keep cutting tools sharp and clean for better and safer performance. - Follow instruction for lubricating and changing accessories. - Inspect tool cords periodically and if damaged have them repaired by an authorized service facility.
Safety Information Important - Please read these instructions fully before starting assembly Mitre Saw Safety Instruction Safety precautions - Do not use saw blades which are damaged or deformed; - Replace the table insert when worn; - Use only saw blades recommended by the manufacturer which conform to en 847-1; - Do not use saw blades manufactured from high speed steel; - Wear suitable personal protective equipment when necessary, this could include: - Hearing protection to reduce the risk of induced hear
In The Box Parts 1 Handle 13 Dust bag 2 Safety release lever 14 Upper blade guard 3 Carbon brush cap 15 Transportation handle 4 Retractable safety guard 16 Dust extraction port (See Fig. A) 5 Fence 17 Support stand (See Fig. B1) 6 Rotary table 18 Trigger switch (See Fig. F) 7 Rotary table locking knob 19 Bevel lock lever (See Fig. G1) 8 Rotary table slot 20 Bevel scale (See Fig. K2) 9 Rotary table mitre angle scale 21 Spindle lock (See Fig.
Assembly Instructions NOTE: Before using the tool, read the instruction book carefully. Intended Use This tool is intended as a stationary machine for making straight lengthways and crossways cuts in wood. Horizontal mitre angles of -45° to +45° as well as vertical bevel angles of 0° to +45° are possible. ASSEMBLY WARNING: To prevent accidental starting that could cause possible serious personal injury, ALWAYS assemble all parts to your saw BEFORE connecting it to the power supply.
Assembly Instructions 3. WORK CLAMP (SEE FIG C) 1) The work clamp can be fitted on either side of the saw and is fully adjustable to suit the size of the workpiece. 2) Do not operate the saw without clamping the workpiece. 3) Make sure that the work clamp securing screws are tightened. A 4. MOUNTING HOLES (SEE FIG D) Before use, the saw can be fixed to a firm, level surface with the 4 mounting bolts (not supplied).
Operating Instructions B1 B2 1. RELEASING THE SAW HEAD (SEE FIG E1, E2) When boxed or during storage, transportation, the saw head is locked in the down position. To release the head ready for operation, apply downward pressure and pull out the lock pin (a) The head will be raised gently to upper position. 2. STARTING THE SAW (SEE FIG F) Press the trigger switch (18). Allow the motor to reach full speed.
Operating Instructions F G1 F 18 G1 made as a chop cut. F 218be G1 For most convenient operation, your sliding mitre saw is equipped with mitre detents for fast 218and accurate mitre cuts of common mitre angles (Left: 45°, 30°, 22.5°, 15°;0°; Right: 0° ,15°, 30°, 45°). 2 22.5°, The rotary table locking knob (8) is used to lock the table at the desired mitre angle.
H2 Maintenance I1 WARNING: Remove the plug from the socket before carrying out any adjustment, servicing or maintenance. When all the adjustments, settings or maintenance have been done, make sure that all keys and wrenches have been removed and that all screws, bolts and other fittings are securely tightened. There are no user serviceable parts in your power tool. Never use water or chemical cleaners to clean your power tool. Wipe clean with a dry cloth. Always store your power tool in a dry place.
J1 Maintenance J2 Similarly, b check that the angle of the blade to the face of the rotary table is 90o. If necessary, adjust the tilt angle of the saw head at the 90o position: loosen the bevel lock (19) and adjust the 0° bevel adjustment screw (c) to bring the saw blade into alignment with the square. Loosen the head screw (c) holding the pointer of the bevel scale (20) and adjust the position of the pointer so that it accurately indicates zero on the scale. Retighten the screw.
L1 L2 b Maintenance Remove the blade, (we recommend the use of a stout glove for this). Clean any saw dust and debris from the arbor and saw blade securing flanges. To refit the blade, follow the above procedure in reverse order. CAUTION: ALWAYS install the blade with the blade teeth and the arrow printed on the side of the blade pointing down at the front of the saw. The direction of blade rotation is also stamped with an arrow on the upper blade guard. L3 3.
Technical Data Technical Data Table Rated voltage 230-240V~50Hz Rated Input power 1200W No load speed 4500 /min Bevel capacity 0-45° Mitre capacity 0-45° L&R Blade size 210 mm Protection class /II Machine weight 6.
Environmental Protection Waste electrical products must not be disposed of with household waste. Please recycle where facilities exist. Check with your local authorities or retailer for recycling advice.
Guarantee This product is selected for DOMESTIC USE ONLY and not for business use. This product is guaranteed against manufacturing defects for a period of 24 months. This does not cover the product where the fault is due to misuse, abuse, use in contravention of the instructions, or where the product has been the subject of unauthorised modifications or alterations, or has been the subject of commercial use.
Plug Replacement (Uk & Ireland Only) If you need to replace the fitted plug then follow the instructions below. IMPORTANT The wires in the mains lead are colored in accordance with the following code: Blue – Neutral Brown – Live As the colors of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows. The wire which is coloured blue must be connected to the terminal which is marked with N.
