Smart Full Body Composition Scale Model No.
Quick Start Guide 1. Download the "Starfit" App from App Store or Google Play. 2. Place the scale on the hard flat surface. 3. Measure with bare feet and fully contact with the electrodes. 4. Turn on the smart App and get the scale connected before measuring. 5. Follow below operations and make sure the posture is correct for measuring.
Smart Full Body Composition Scale Thanks for choosing Smart Full Body Composition Scale. This scale uses bio-electrical impedance analysis (BIA) technology to help you conveniently measure Body weight, Body balance, BMI, Body fat rate, Visceral fat, Body water, Skeletal muscle rate, Muscle mass, Bone mass, Protein, BMR, Body age and etc. ! WARNING ●DO NOT use with medical implants such as pacemakers. ●DO NOT stand on the edge of the scale or jump on it; ●DO NOT overload the scale (Max.
Indication Symbols The batteries in the scales are too weak. Insert new batteries (Please charge the scale with type-C cable.). More than 180kg are on the scales. The scales are overloaded. An error has occurred during measurement. Step off the scales for 5 seconds and step onto them again to repeat the measuring process.
Indication Symbols iOS: 8.0 or higher Android: 5.0 or higher Install Starfit App 1.Scan the below QR Code to download APP, or search “Starfit” from App Store and Google Play. 2.Download and install the App “Starfit” on your phone. 3.The App icon will appear on your phone after the installation is completed. How to use the scale with Starfit App for the first time? 1.Open the App “Starfit” on your device. 2.Register your own account by email or login with social media account. 3.
4.iOS: Make sure Bluetooth is on and Bluetooth Authorization is allowed. Android: Make sure Bluetooth is on and GPS and Location is allowed. 5.In the back of scale, pull out the insulation sheet, then place the scale on a hard, flat surface, step onto the scale with single foot to activate the scale. Wait until the display shows “0.0lb”. 6.Pair the scale through Bluetooth. Make sure the scale is on when pairing. Leaving the APP on its main screen, it will automatically connect to the scale.
Body Composition Analysis Report Click " " to view your Body Composition Analysis Report. You can also click " " to select save to local, print or share to friend via facebook, instagram, or SMS.
Bluetooth Connection 1) Regular Connection See the "How to use the scale with Starfit App for the first time?" chapter 2 ) If the regular connection to Bluetooth failed, please try the below steps: 1. Reset the scale by taking out one battery for 5 seconds and putting it back in. 2. Reset the Bluetooth connection. Ensure Bluetooth and GPS (Android only) are enabled on your device. Troubleshooting 1. Bluetooth failed to connection.
6.The scale does not turn on. ●Check if the insulation sheet has been pulled out. ●Check if battery has run out of power and change new batteries if needed. Frequently Asked Questions & Answers 1.How to get the most accurate result? - Stand on the scale firmly, do not shake when weigh-in. - Take your measurement at the same time each day to ensure the most accurate results. - Please place your scale on the hard/flat ground, then step on the scale with bare feet, after that the display will be turned on.
Holder Usage 1. Please remove the sticker from the included holder and attach it to the wall considering the length of the string. 2. Please place the handle on the holder when it is not used.
Frequently Asked Questions&Answers 1.Why doesn't the scale work? Why does the data on screen disappear in a flash? - Please check the batteries are installed properly, replace batteries if necessary. 2. The scale cannot connect with App. - Check that the phone's software is iOS 8.0 or higher or Android6.0 or higher. - Download and open the newest version of the Starfit App. - Enable Bluetooth on your phone. For Android 6.0 or higher, location needs to be enabled 3.No body fat measured when weighing.
FCC Statement Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
