Robot vacuum cleaner Important Safety Instructions WARNING: TO REDUCE THE RISK OF INJURY OR DAMAGE, READ THE FOLLOWING SAFETY PRECAUTIONS WHEN SETTING UP, USING AND MAINTAINING YOUR ROBOT. • CAUTION This product is designed for indoor floor cleaning only, do not use it outdoors(such as on an open-ended terrace), on any surface other than the ground(such as a sofa), or in any commercial or industrial environment.
Important Safety Instructions Battery and Charging Do not charge non-rechargeable batteries. For the purposes of recharging the battery, only use the detachable supply unit 360 robot provided with this product. Do not dismantle, repair or modify the battery or charging dock. Keep the charging dock away from heat(such as heating vents). The battery must be removed from the appliance before it is scrapped. The product must be disconnected from the power supply when removing the battery.
OPE N Product Introduction Robot vacuum cleaner Charging dock Adapter Dust bin Electrical water tank Remote control AAA AAA AAA Battery Cleaning for remote control x2 tool HEPA filter Mop cloth 3 Side brushes User manual
Product Introduction Top view Docking station Visual camera Power/Auto cleaning Hotspot AP distribution network Spot cleaning Smart distribution network Recharge Power indicator Anti-collision bumper Speaker Power switch Dust bin Charging contacts Bottom view Cliff sensor Charging metal contact piece Side brush Charging metal Contact piece Omnidirectional wheel Side brush Power Socket Cable lines collect slot Battery cover Back wheel Back wheel Anti-slip mat Main brush Dust bin 4
Product Introduction Remote control Dust bin Auto cleaning Primary filter Sponge filter Recharge button On/Pause button Direction forward Left direction Right direction Dust bin cover Spot cleaning Edge cleaning Dust bin button Seek the robot HEPA filter Suction power Dust bin block slice Dust bin unit Water tank Water tank cover High efficiency filter Sponge filter Primary filter Water tank latch Water tank unit Water tank button 5 Water flow control OPEN
Installation Using the robot 3. Turn the robot over to install the side brushes. 1. Remove the EVA foam on each side. Install the side brushes 2. Place the charging dock against the wall on a flat surface and plug it into the power socket. Install the side brushes on both sides of the roller at the bottom of the main unit.
Installation Using the robot 4. Power and charge 6. Water tank 1. Auto: After cleaning, the robot will automatically return to the charging dock to charge. 1. Open the water tank, fill it with water, and close it tightly. 2. Install the mop cloth. 3. Install water tank. 4. Start mopping. 2. Manual: In Pause mode, press the button to send the robot back to the charging dock. 3. Recharge by remote control. Note: 1. The battery is fully charged to prolong the battery life.
Instructions for use Auto Cleaning Edge Cleaning The robot defaults auto cleaning mode after power on. Zig-zag cleaning. The robot cleans around the wall edge. Spot Cleaning Applicable for garbage concentrated area. The robot cleans in a spiral shaped in designated area. After cleanup, the robot will return to the center of square. Schedule Cleaning Use the app to set start times for scheduled cleanups. The default cleaning mode is auto cleaning.
App Instruction Download the mobile phone App Method 1:Search for "Botslab" in Google Play or App Store and download it. Method 2 :Scan the QR code below by using mobile phone camera or any QR code scanner App to download the Botslab App. Botslab Note: Please check out further operation instructions in "My - My Service" on the App and do not hesitate to contact us if you have any if you have any questions or comments.
Maintenance Main brush assembling and cleaning Dust bin and filter cleaning It is recommended to clean the dust bin and filter in time. A. Pull out the dust bin by pressing the button on the back of robot. Side brush cleaning B. Press and hold the button on the dust bin to open the dust bin and take out the garbage. A. Use a brush cleaning tool to cut off the entangled debris. B. Use a clean cloth to clean the side brush.
Maintenance Specifications Omnidirectional wheel cleaning Main unit 1. Turn the robot over. 2. Pull out the wheel upwards. 3. Reinstall after cleaning and press firmly. 4. Rinse the axle and the wheel with water to remove any hair and dirt. 5. Dry and reinstall the wheel then press it back in place. Name 7 Dimensions 320*320*76mm Product weight 2.9Kg Battery capacity Minimum capacity: 2500mAh, 36Wh Standard capacity: 2550mAh, 36.72Wh Rated voltage 14.
Troubleshooting Error Solution The main brush is tangled up Please clean the roller brush The side brush is tangled up Please clean the side brush A wheel is abnormal and the robot jammed Please check the driving wheels The dust bin abnormal installation Please install the dust bin Abnormal cliff sensor / dirty cliff sensor Please wipe the cliff sensors The robot is stuck Please clean any obstacle around it The bumper is stuck Please check the front bumper The robot is suspended Please put
FAQs Problem Solution Difficult to recharge There are too many obstacles near the charging dock. Move it to an open area. The robot is too far from the charging dock. Place it closer and retry. Poor cleaning ability It is recommended to clean up the ground debris first. If there is a part missing to clean, the robot will automatically schedule to clean it. The robot is jammed The robot will actively try various methods to get rid of jams. Or it is recommended to help manually.
Product parameter Name and content of hazardous substances in the product Parts Name Circuit Metal Parts Plastic Casing Battery Other Parts This form is compiled in accordance with the regulations of S J/T 11364. Means that the content of the hazardous substance in all homogeneous materials of the part is below the limit requirement specified in GB/T 26572. Means that the hazardous substance at least in a certain homogeneous material of the part exceeds the limit requirement of GB/T 26572.
15
