Daily Maintenance Rolling brush (clean it regular} 1. turn over the host machine and press the buckle on the main brush cover io take out the roller brush. 2. use the configured cleaning tool fo clean the dust outside the roller brush and inside the roller brush cavity, then remove the entanglements on the roller brush. 3. reassemble the roller brush, and press the main brush cover tightly to fix the buckle buckle roller brush main brush cover 14 Side brush (clean it regularly) 1.
Daily Maintenance Individual Dust bin (clean it regularly} 1. press the button and pull out the dust bin backward. 15 Cleaning Filters {clean it regularly} 1. after a long ime usage, remove the primary filter, foam filter, HEAP fitter. 2. clean the removed fitters under water. 3. shake off the water drops and dry it naturally, then uss it after completely dried. 4. install filters well in sequence: primary filer foam filter HEAP. Liter cover Coma filter HEAP Note: .
Daily Maintenance 2-in-1 electric-controlled water tank {clean it every ime) 1. remove the mopping bracket from the water tank, tear of the Dust box wiping cloth and clean it in water. Coma filter Primary filter . 2. lift the handle fo remove the dust box from the 2-in-1 water tank, Water tank and pour out the residual water in the water tank. a, pa = Mopping bracket Wiping cloth Li-ion battery . the host machine is furnished with high-performance lithium-ion batteries.
Daily Maintenance Sensor (clean it regularly) Pls clean the sensor by soft mop: 1.recharge sensor on the left side of the machine. 2. six anti-drop sensors at the bosom of the machine. 3. two line laser sensors in front of the machine and one line laser sensor on the right side of the machine. 4. liar sensors directly above the machine. §. charging contact at the bottom of the machine, 6. charging seat charging shrapnel! {please power off before cleaning). 7. signal transmitting area of charging base.
common questions Questions Solution Can not boot The battery is low, please place the device on the charging stand and align the charging pads, and the device will automatically turn on (when it is completely dead, it will take a while to automatically turn on) When the ambient temperature is lower than 0f or higher than, please use tithe environment Can't charge Please remove the device, and check whether the indicator light of the charging stand is on, make sure that both ends of the power adapter of the
troubleshooting Fault tone Re solvent battery low, please try again later Put the host on the charging stand for charging dust bin taken out Take out the dust box in standby or suspended working state of the machine. Please replace the dust box Restart it after installed the dust bin Cleaning is triggered when the dust box is taken out. Please reinstall the dust box please clean the right sensor There is dirt or shelter on the sensor along the wall.
troubleshooting Fault tone Re solvent Radar cover is squeezed, please check The upper cover of radar is wrapped or stuck.
Product Hazardous Substance Content and Name Name Harmful substances {Pb} (Hg) {Cd} (PBB) {DEEP) Circuit board assembly Battery Charger Processable Metallic parts Motor Shell O00 Other Accessories Oo O O O00 O00 C0 This form Is prepared according to the provisions of SJ/T 11364 Indicates that the content of the hazardous substance in at least one homogeneous material of the part exceeds the limit requirement specified in LGBT 28572 # Indicates that the content of the hazardous substance in at least one homo
IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precautions should always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING (THIS APPLIANCE) WARNING —To reduce the risk of fire, electric shock, or injury: 1) Do not leave appliance when plugged in. Unplug from outlet when not in use and before servicing. 2) Do not use outdoors or on wet surfaces. 3) Do not allow to be used as a toy. Close attention is necessary when used by or near children.
14) Prevent unintentional starting. Ensure the switch is in the off-position before connecting to battery pack, picking up or carrying the appliance. Carrying the appliance with your finger on the switch or energizing appliance that have the switch on invites accidents. 16) Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.
25.This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have bean given supervision or instruction concerning use of the appliance by a person responsible for their safety. 26.Children should be supervised to ensure that they do not play with the appliance. 27 the appliance is only to be used with the power supply unit provided with the appliance. 28.
Warranty Policy and Customer Service Information Thank you for purchasing the product! If there is a product quality problem within 12 months from the date of purchase Warranty period The after-sales service of cleaning reboot products is strictly in accordance with the "Consumer Rights Protection Law of the People's Republic of China" and "Product Quality Law of the People's Republic of China” to implement after-sales three guarantees services. The service contents are as follows: Free return service 2.
Warranty Policy and Customer Service Information Non-Warranty Policy 1. Exceed the warranty period 2. Damage caused by not using tin accordance with the requirements in the instruction manual or user guide 3. Damage caused by man-made reasons 4. Failures caused by unauthorized disassembly, repair, and modification of the product 5. Damage caused by force manure factors (such as floods, earthquakes, lightning, tee) €. No warranty card, invoice or warranty card does not match the invoice information 7.
FCC Statement 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: {1} This device may not cause harmful interference, and {2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
FCC Statement (Cont.) Consult the dealer or an experienced radio/TV technician for help. IC warning This device contains license-exempt that comply with Innovation, Science and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device.
Declaration of Conformity (DoC) Hereby, Guangdong Kwangju Intelligent Robot declares that this equipment is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. Type of Operating Frequency Maximum RF Windlass {MHZ} Power 2412-2472 xo dBm 5150-5350 xr dBm ELAN 5470-5725 x dBm 5725-5828 20x dBm Operations in the band are restricted to indoor use only.
Tree items in cloud vouchers The information of user The information of product Name: The type of product: Tel number: The color of product : Address: Product Serial Number: Email : Order date: Maintenance record Mum Date Trouble phenomenon and treatment method maintenance engineer
